Very low threshold graded-indexseparate-confinement-heterostructure strained InGaAsPsingle-quantum-well lasers

A low threshold current density of ~100 A/cm² has been obtained at 1.55 μm using a graded-index separate-confinement-heterostructure strained InGaAsP single-quantum-well laser. The design of the laser structure is based on results calculated from the viewpoint of effective carrier injection into the well     

Stabilization of inter-area and/or oscillatory modes in large-scale power system by voltage impedance power system (VIPS) apparatus based on decentralized control scheme

New technologies such as power electronics have made it possible to change continuously the impedance of a power system not only to control power flow but also to enhance stability. A power system incorporating a variable impedance apparatus such as a variable series capacitor (VSrC) and high-speed phase shifter (HSPS) is called VIPS (Variable Impedance Power System) by the authors. This paper proposes a novel control method of VIPS apparatus such as VSrC and HSPS installed at an interconnecting point for stabilizing inter-area unstable and/or oscillatory modes. The proposed design method of the control system is a kind of hierarchical decentralized control method of a large-scale power system based on a Lyapunov function. Under the proposed control scheme, each subsystem can be stabilized independently by local controllers such as AVR, speed governor and PSS, and then the whole interconnected system can be stabilized by VIPS apparatus taking into account interactions between subsystems. The effectiveness and robustness of the VIPS apparatus control are shown by numerical examples with model systems including a large-scale power system.     

The relation between luminous properties and oxygen content inZnS:TbOF thin-film electroluminescent devices fabricated byradio-frequency magnetron sputtering method

The purpose of this paper is to study the relationship between the oxygen concentration and brightness degradation in ZnS:TbOF green thin-film electroluminescent (EL) devices. The characteristics including crystallinity, optical, and electrical properties were discussed. The brightness-voltage (B-V) measurement results shelved that with higher oxygen-content in ZnS:TbOF phosphor layer, lower brightness was measured. It was consistent with the poor crystallinity, worse photoluminescent intensity, and easier to get moisture in the oxygen-rich (O/Tb>1) phosphor film. Furthermore, deep level transient spectroscopy (DLTS) measurements identified that when the O/Tb ratio was greater than 1, the oxygen-related deep hole traps E_H1 and/or E_H2 could be detected in the ZnS:TbOF phosphor layer. These E _H1 and/or E_H2 traps were believed to be the main killers for the brightness of the device since they capture most of the holes from the generated electron-hole pairs. This evidence strongly supports that the modified energy transfer model is more dominant than direct impact excitation during the luminescent process     

Practical method for generation expansion planning based on dynamic programming

This paper presents an efficient method which provides the optimal generation mix and the optimal generation construction process. The approximation method in which the dynamic programming technique and gradient method are combined is applied to determine the optimal generation mix with hydropower generation technologies. The successive approximations dynamic programming (SADP) technique, which is very suitable for high-dimensional multistage decision process problems, is used for obtaining the optimal generation construction process. The effectiveness and feasibility of the developed technique are demonstrated on a practical power system model which has five types of generation technologies including a hydropower generation technology.     

Rutile-type TiO2 thin film for high-k gate insulator

We investigated rutile-type titanium dioxide (TiO₂) films for possible use as a high-k gate insulator. The TiO₂ thin films were directly deposited on Si substrates using a RF magnetron sputtering method with a sintered oxide target. A single phase of rutile-type TiO₂ whose dielectric constant of approximately 75 was obtained when the film was deposited in an inert gas atmosphere and annealed at 800 °C in an oxidizing gas atmosphere. The oxygen ions were deficient in the as-deposited film, and consequently, a sufficient oxygen supply was needed to crystallize the film to a single phase of rutile during the post-annealing. However, the interfacial SiO₂ layer between the TiO₂ and the Si substrate simultaneously grew thicker than 2 nm. As the interfacial SiO₂ grew, the leakage current was decreased and the equivalent oxide thickness was increased, in the Au/rutile-type TiO₂/Si capacitor. Therefore, we concluded that the growth of the interfacial SiO₂ layer thicker than 2 nm is inevitable to form the single phase of rutile-type TiO₂ and to decrease the leakage.     

Determination of three dimensional in situ stress from core discing based on analysis of principal tensile stress

To determine all of the components of in situ stress from core discing, both the directions and magnitudes of the principal in situ stresses must be determined for a disc of a given thickness. In this study, we analyzed the direction and magnitude of tensile stress below an HQ core stub for 11 core lengths using stress conditions under which core discing is likely to occur. First, based on an analysis of the direction of tensile stress below the core stub, we propose a method for determining directions of in situ stress from the height distribution at the periphery of the end surface of a disc. This method can be used with a disc of any thickness. Next, based on an analysis of the magnitude of tensile stress in the central part of a core, we propose a linear criterion for core discing, which can be applied to a core of any length. This criterion was in good agreement with an empirical formula obtained previously in laboratory experiments. By combining information on the direction of in situ stress and the linear criterion for core discing, we propose a method for determining all of the components of in situ stress from core discing under the assumption that vertical stress is given by the overburden stress. Finally, these methods were applied to discs obtained from a field where hydraulic fracturing was performed to measure horizontal stresses. The results showed that the azimuths of the principal stresses estimated from core discing were consistent with those of the principal horizontal stresses determined by hydraulic fracturing and that while the magnitudes of the principal horizontal stresses estimated from core discing showed a large scatter, they were similar to those determined by hydraulic fracturing.     

Cytomegalovirus disease accompanied by severe hypoproteinemia in a patient with adult T-cell leukemia-lymphoma

A 62-year-old Japanese man complained of fever, general fatigue, anorexia and watery diarrhea during remission of adult T-cell leukemia-lymphoma. Laboratory examinations showed severe hypoproteinemia (2.9 g/dl). However, neither intestinal lesions associated with ATL nor findings suggesting protein losing gastroenteropathy were observed. Cytomegalovirus (CMV) antigen detection assay using peripheral blood leukocytes revealed that he had an active CMV infection with hemophagocytic syndrome. Treatment with ganciclovir and methylprednisolone led to an improvement of hypoproteinemia. CMV disease and associated hemophagocytic syndrome should be considered as a cause of hypoproteinemia in an immunocompromised host.     

Infrared sensing properties of positive temperature coefficient thermistors with large temperature coefficients of resistivity

Infrared (IR) detecting elements were prepared using positive temperature coefficient (PTC) thermistors with large temperature coefficients of resistivity (α). Their compositions were denoted as Ba_1−x Sr _x Nb_0.003Ti_0.997O₃ + 1 mol % TiO₂ + 0.07 mol %MnO (x=0, 0.2), and their temperature coefficients of resistivity were 78 and 50% K⁻¹, respectively. Their IR sensing properties were measured under the self-regulating heating conditions, and were compared with those of a detector with small α (18 % K⁻¹). It was shown that large α was effective for controlling the element temperature by self-regulating heating and for improving sensitivity. The responsivity,R _v of the element withx=0.2 was 980 VW⁻¹, and was as large as those of pyroelectric detectors. Expressions which normalize the sensitivity and the thermal time constant were derived. From these expressions, criteria for improving some IR sensing properties were obtained.     

Gelation mechanism of agarose and κ-carrageenan solutions estimated in terms of concentration fluctuation

The gelation mechanism of agarose and κ-carrageenan aqueous solutions was investigated by using polarized light scattering and X-ray diffraction techniques in terms of the liquid-liquid phase separation. When an incident beam of He-Ne gas laser was directed to the gel prepared by quenching the agarose solution, the logarithm of scattered intensity increased linearly in the initial stage and tended to deviate from this linear relationship in the latter stage. If the linear increase in the initial stage could be analyzed within the framework of the linear theory of spinodal decomposition proposed by Cahn, the phase diagram indicated that the gelation is attributed to the phase separation due to the concentration fluctuation of solution. Furthermore, in the later stage showing the deviation of the linear relationship, light scattering under Hv polarization condition showed a X-type pattern indicating the existence of optically anisotropic rods, the optical axes being parallel or perpendicular with respect to the rod axis. In spite of the existence of the rods, no crystallites were confirmed by the corresponding X-ray diffraction and DSC measurements. For κ-carrageenan solutions, the logarithm of scattered intensity against time showed a constant value. This indicated that the gelation of κ-carrageenan solutions is independent of liquid-liquid phase separation but is due to the rapid formation of cross-linking points. Accordingly it turns out that the small difference of chemical structure between agarose and κ-carrageenan causes quite different gelation mechanism.     

Damage tolerance of glass mat/epoxy laminates hybridized with flexible resin under static and impact loading

This study deals with the impact property and damage tolerance of matrix hybrid composite laminates with different laminate constitution. The matrix hybrid composite laminates consisted of the laminae with a conventional epoxy resin and the laminae with a flexible epoxy resin modified from the conventional resin to avoid the interlaminar delamination. The impact energy absorption ratio greatly depended on the matrix resin placed at the impact face. The energy absorption was almost constant if the conventional resin was placed at the impact surface layer, while it increased exponentially with the increasing fraction of the flexible resin if the flexible resin was placed at the impact face. The impact energy was absorbed by the damage development and propagation in the laminate with conventional resin laminae as the impacted face, while it was absorbed by both the recoverable deformation of the flexible resin and the damage propagation in the laminate with flexible resin laminae as the impacted face.