Formation of acrylamide in microwave-roasted sorghum and associated dietary risk

The effect of microwave roasting parameters (300, 450 and 600 W; 5, 10 and 15 min) on acrylamide content in sorghum grain was determined using High Pressure Liquid Chromatography (HPLC)-photo diode array (PDA) detector coupled with C-18 column. Samples roasted at 300 and 450 W did not possess acrylamide, whereas 600 W (15 min) favoured formation of 2740.19 µg/kg of acrylamide, levels far exceeding the defined European Union (EU) limits. The chronic daily intake (CDI) for acrylamide through consumption of such grain flour was 3.25–9.5-fold higher to Joint FAO/WHO Expert Committee on Food Additives (JECFA) defined high exposure limits. The margin of exposure (MOE) values ranged from 4.3 to 12.76 and from 11.07 to 32.27 for neoplastic and neurological effects, respectively, demonstrating high exposure and serious health concerns associated with dietary intake of this toxicant. This study assesses the risk for the Indian population and highlights the importance of optimising process parameters for food product to minimise such exposure risks.     

Development of a simple low-cost solar simulator for indoor collector testing

Indoor test methods for solar collectors are widely accepted and recommended by ASHRAE. The development of a solar simulator for indoor testing and the certification procedure for photo-thermal solar devices is discussed in this paper. The system consists of 14 quartz halogen lamps and provides a testing area of about 1 × 1 m. The irradiance can be varied from 400 to 1500 W/m². This is achieved by varying the input power supplied to individual lamps. The radiation output characteristics of a single lamp have been studied. The distribution of intensity over the covered area of 1·20 × 1·20 m has been recorded using a precision Eppley pyranometer.A variety of collectors—evacuated tubular collectors and flat-plate collectors of both liquid and air heating types—has been tested under sufficiently stable insolation conditions. Results for a conventional solar air heater are presented together with suggestions for further improvements.     

On connections between 3-d microstructures and their 2-d images

The problem of recovery of three-dimensional microstructural parameters from two-dimensional images is addressed in its inverse form. Three-dimensional inhomogeneous solids with known microstructures are generated virtually and images of their cross-sections are analyzed. Three different types of randomly oriented microcracks and microcracks having preferential orientation with some scatter. Somewhat unexpected result is that, in all the cases considered, three-dimensional defect densities are very close to average values of corresponding two-dimensional parameters.     

Scientific basis for establishing country greenhouse gas estimates for rice-based agriculture: An Indian case study

A comprehensive scientific assessment of CH₄ budget estimation for Indian rice paddies, based on a decade of measurements in India, is presented. Indian paddy cultivation areas contain soils that have low to medium levels of soil organic carbon. The average seasonally integrated CH₄ flux (E _sif) values calculated from these measurements were 15.3 ± 2.6 g m^–2 for continuously flooded (CF), 6.9 ± 4.3 g m^–2 for intermittently flooded (IF) single aeration (SA) and 2.2 ± 1.5 g m^–2 for IF multiple aeration (MA) rice ecosystems. For CF and IF (MA) rice ecosystems having high soil organic carbon, without organic amendments, the CH₄ flux (E _sif) may be increased by 1.7 times relative to low soil organic carbon, whereas it may enhance by 5.3 for CF if amended organically. Organic amendment and high soil organic carbon paddy areas do not alter the methane budget estimates for India (3.6±1.4 TgY^–1) much, due to their small paddy harvested area. Methane estimated using average emission factors (E _sif) for all paddy water regimes, which include harvested areas having soils with high organic carbon and organic amendments, may give a budget of 5 TgY^–1 for India.     

Optimization of process parameters affecting surface roughness in magnetic abrasive finishing process

Development in manufacturing technology enhances the mechanical behavior of machined parts and improves the surface finish with high precision, which conveys the progressive importance of magnetic abrasive finishing (MAF) process. In current research work, magnetic abrasive particles were used as finishing tools during the MAF process. However, these magnetic abrasives are fabricated by special techniques, i.e., the adhesive bonding-based method, the sintering method, the plasma-based method and so on. The present study explores the basic finishing characteristics of the magnetic abrasive produced by the sintering process. After the sintering process, improved quality of magnetic abrasives was obtained, where the abrasive particle sticks on the base metal matrix. The abrasive particle used is alumina powder and the magnetic particle is iron powder. Experiments were performed on Stainless Steel 202 to inspect the sound effects of several process parameters such as rotational speed, electromagnet voltage, machining gap and abrasive particle size on machining performance. Apart from that, surface roughness was also measured, which revealed the influence of the abrasive particle on the machined surface in terms of surface finish. It is observed from this study that appropriate size of magnetic abrasive particle optimizes the surface finish.     

Decomposition-based design optimization method using genetic co-evolution

The paper examines new strategies for the implementation of genetic algorithms in a decomposition-based approach for design. In this approach, the design problem is decomposed into smaller-sized sub-problems, the solutions for which are obtained through co-evolution. The emphasis resides in evaluating methods for exchanging design information relevant to coordinating solutions of temporarily decoupled sub-problems. Methods based on modification of genetic makeup through experiential inheritance (exposure to another species), and through inter-species migration are investigated in this work. Different forms of design problem coupling are investigated, ranging from coupling through constraints only, to coupled objective and constraint functions. The proposed strategies are validated through implementation in representative algebraic and structural design problems.     

Adaptive Discretization for Computerized Tomography

Two adaptive discretization frameworks are tested for computerized tomography (CT) data reconstruction. Removal of inactive pixels is primary motivation. Efficient and user independent entropy optimized masking is employed for spatial filtering purposes. Density of nodes at high gradient of reconstructed physical property is used as adaptation criterion. An alternative option, independent from noisy projection data and nature of the physical properties, is also discussed. Sensitivity analysis between the uniform and nonuniform (evolved via adaptive route) reconstruction grid reveals the utility of nonuniform grids. Iterative and transform based reconstruction techniques are used. Outcomes are tested successfully on three real world projection data from two different compact CT setups and one commercial high-resolution micro-CT scanner.