Long-term sensor measurements of lung deposited surface area of particulate matter emitted from local vehicular and residential wood combustion sources

Abstract

Lung deposited surface area (LDSA) is a relatively new metric that has been argued to be more accurate at predicting health effects from aerosol exposure. For typical atmospheric aerosol, the LDSA concentration depends mainly on the concentration of ultrafine particles (e.g. vehicular exhaust emissions and residential wood combustion) and therefore optical methods cannot be used to measure and quantify it. The objective of this study was to investigate and describe typical characteristics of LDSA under different urban environments and evaluate how a diffusion charging-based Pegasor AQ Urban sensor (Pegasor Ltd., Finland) can be used as an alternative to optical sensors when assessing local combustion emissions and respective LDSA concentrations. Long-term (12?months) sensor measurements of LDSA were carried out at three distinctly different measurement sites (four sensor nodes) in the Helsinki metropolitan area, Finland. The sites were affected mainly by vehicular exhaust emission (street canyon and urban background stations) and by residential wood combustion (two detached housing area stations). The results showed that the accuracy of the AQ Urban was good (R² = 0.90) for the measurement of LDSA when compared to differential mobility particle sizer. The mean concentrations of LDSA were more than twice as high at the street canyon (mean 22 µm² cm^?3) site when compared to the urban background site (mean 9.4 µm² cm^?3). In the detached housing area, the mean concentrations were 12 µm² cm^?3, and wood combustion typically caused high LDSA peaks in the evenings. High correlations and similar diurnal cycles were observed for the LDSA and black carbon at street canyon and urban background stations. The utilization of a small-scale sensor network (four nodes) showed that the cross-station variability in hourly LDSA concentrations was significant in every site, even within the same detached housing area (distance between the two sites ～670?m).     

A review on some classes of algebraic systems

ABSTRACT

In this paper, we review some algebraic control system. Precisely, linear and bilinear systems on Euclidean spaces and invariant and linear systems on Lie groups. The fourth classes of systems have a common issue: to any class, there exists an associated subgroup. From this object, we survey the controllability property. Especially, from those coming from our contribution to the theory.     

Temperature cycling and its effect on mechanical behaviours of highporosity chalks

Temperature history can have a significant effect on the strength of water-saturated chalk.In this study,hydrostatic stress cycles are applied to understand the mechanical response of chalk samples exposed to temperature cycling between each stress cycle,compared to the samples tested at a constant temperature.The total accumulated strain during a stress cycle and the irreversible strain are reported.Chalk samples from Kansas(USA)and Mons(Belgium),with different degrees of induration(i.e.amount of contact cementation),were used.The samples were saturated with equilibrated water(polar)and nonpolar Isopar H oil to quantify water weakening.All samples tested during 10 stress cycles with varying temperature(i.e.temperature cycled in between each stress cycle)accumulated more strain than those tested at constant temperatures.All the stress cycles were performed at 30℃.The two chalk types behaved similarly when saturated with Isopar H oil,but differently when saturated with water.When saturated with water,the stronger Kansas chalk accumulated more total strain and more irreversible strain within each stress cycle than the weaker Mons chalk.     

Demonstration of a tool for automatic learning and re-use of knowledge in the activated sludge process.

Wastewater treatment plant operators encounter complex operational problems related to the activated sludge process and usually respond to these by applying their own intuition and by taking advantage of what they have learnt from past experiences of similar problems. However, previous process experiences are not easy to integrate in numerical control, and new tools must be developed to enable re-use of plant operating experience. The aim of this paper is to investigate the usefulness of a case-based reasoning (CBR) approach to apply learning and re-use of knowledge gained during past incidents to confront actual complex problems through the IWA/COST Benchmark protocol. A case study shows that the proposed CBR system achieves a significant improvement of the benchmark plant performance when facing a high-flow event disturbance.     

Benchmark simulation Model no 2 in Matlab-simulink: towards plant-wide WWTP control strategy evaluation.

In this paper, implementation of the Benchmark Simulation Model No 2 (BSM2) within Matlab-Simulink is presented. The BSM2 is developed for plant-wide WWTP control strategy evaluation on a long-term basis. It consists of a pre-treatment process, an activated sludge process and sludge treatment processes. Extended evaluation criteria are proposed for plant-wide control strategy assessment. Default open-loop and closed-loop strategies are also proposed to be used as references with which to compare other control strategies. Simulations indicate that the BM2 is an appropriate tool for plant-wide control strategy evaluation.     

Analysis of phosphorus removal and anaerobic selector performance in a full-scale activated sludge process in Singapore.

This paper analyses the performance of the anaerobic selector (A/O process) in a full-scale activated sludge process receiving mostly industrial sewage discharge (> 60%) in Singapore. In addition to the sludge settleability, enhanced biological phosphorus removal (EBPR) was studied. The sludge volume index (SVI) reduced from 200 to 80 ml g(-1) and foaming was suppressed significantly, indicating the effectiveness of the anaerobic selector in improving sludge settleability. The phosphorus removal efficiency was 66%, and 7.5 mg HAc-COD was consumed per mg PO4(3-) -P removed. In the anaerobic compartment, 31% of the SCOD and 73% of the acetic acid in the settled sewage were removed with PO4(3-) -P release of 14.1 mg PO4(3-)-P l(-1). The linear correlation between PO4(3-) -P release in the anaerobic compartment and PO4(3-) -P uptake in the aerobic compartment indicates that there is about 0.8 mg PO4(3-) -P release in the anaerobic compartment per mg PO34(3-) -P uptake in the aerobic compartment. The fates of volatile fatty acids (VFAs) and its short chain acids (SCAs) in the process were studied and discussed.     

Optimizing the tapping regime on a blast furnace operating at variable speed

The main factors that determine the uniformity with which smelting products are tapped from a blast furnace are the rate of accumulation of the products in the hearth and the tapping rate. The first parameter is in turn determined by the stability of the furnace’s operation and can vary significantly even over the course of 24 h. The second parameter is determined mainly by the condition of the iron notch, the maintenance it receives, any changes that occur in the diameter of the channel of the notch, and the quality of the materials used to form the notch. Recommendations are presented to optimize tapping of the smelting products.     

On the problem of hydrogen removal during heat treatment of large forgings

The solutions to a differential equation for the problem of heating of a cylinder in a medium with a fixed temperature are used to obtain equations for estimating the change in the hydrogen concentration in forgings from data on the hydrogen concentration at the cylinder axis or on the average bulk hydrogen concentration. Similar equations are also obtained for forgings having square cross sections. The calculation demonstrates that, for the case of a twofold decrease in the hydrogen concentration in a forging, the calculated times of annealing of a cylindrical forging differ by three times.     

Volumetric out-of-furnace heat treatment of 3600-M3 decomposers

Specifications require that all the welds in 12-m-diam. decomposers with a capacity of 3600 m³ be subjected to high-temperature tempering before going into service in order to alleviate the stresses from the welding operation. Specialists at the organizations VNIIPTkhimnefteapparatury and VNIImontazhspetsstroi have proposed out-of-furnace volumetric (complete) of the assembled decomposer with the use of special heaters. The use of this heating method has shortened assembly operations while providing the welds with a highquality heat treatment and reducing the stresses overall (including welding stresses, stresses from assembly of the decomposer, etc.) The technology ensures uniform heating of the housing of the decomposer and provides for close control over the process. The experience gained in heat-treating decomposers can also be used in the construction of other containers that come into contact with corrosive media. __________ Translated from Metallurg, No. 3, pp. 61–64, March, 2006.     

Reliable eye-diagram analysis of data links via device macromodels

This paper addresses the impact of device macromodels on the accuracy of signal integrity and performance predictions for critical digital interconnecting systems. It exploits nonlinear parametric models for both single-ended and differential devices, including the effects of power supply fluctuations and receiver bit detection. The analysis demonstrates that the use of well-designed macromodels dramatically speeds up the simulation as well it preserves timing accuracy even for long bit sequences.