Long-term sensor measurements of lung deposited surface area of particulate matter emitted from local vehicular and residential wood combustion sources

Abstract

Lung deposited surface area (LDSA) is a relatively new metric that has been argued to be more accurate at predicting health effects from aerosol exposure. For typical atmospheric aerosol, the LDSA concentration depends mainly on the concentration of ultrafine particles (e.g. vehicular exhaust emissions and residential wood combustion) and therefore optical methods cannot be used to measure and quantify it. The objective of this study was to investigate and describe typical characteristics of LDSA under different urban environments and evaluate how a diffusion charging-based Pegasor AQ Urban sensor (Pegasor Ltd., Finland) can be used as an alternative to optical sensors when assessing local combustion emissions and respective LDSA concentrations. Long-term (12?months) sensor measurements of LDSA were carried out at three distinctly different measurement sites (four sensor nodes) in the Helsinki metropolitan area, Finland. The sites were affected mainly by vehicular exhaust emission (street canyon and urban background stations) and by residential wood combustion (two detached housing area stations). The results showed that the accuracy of the AQ Urban was good (R² = 0.90) for the measurement of LDSA when compared to differential mobility particle sizer. The mean concentrations of LDSA were more than twice as high at the street canyon (mean 22 µm² cm^?3) site when compared to the urban background site (mean 9.4 µm² cm^?3). In the detached housing area, the mean concentrations were 12 µm² cm^?3, and wood combustion typically caused high LDSA peaks in the evenings. High correlations and similar diurnal cycles were observed for the LDSA and black carbon at street canyon and urban background stations. The utilization of a small-scale sensor network (four nodes) showed that the cross-station variability in hourly LDSA concentrations was significant in every site, even within the same detached housing area (distance between the two sites ～670?m).     

A review on some classes of algebraic systems

ABSTRACT

In this paper, we review some algebraic control system. Precisely, linear and bilinear systems on Euclidean spaces and invariant and linear systems on Lie groups. The fourth classes of systems have a common issue: to any class, there exists an associated subgroup. From this object, we survey the controllability property. Especially, from those coming from our contribution to the theory.     

Optimal weighed Holoentropy for video compression: an advanced HEVC

ABSTRACT

In recent times, the applications of multimedia are rising in a greedy mode and hence the amount of video transactions is also increasing exponentially. This has shouted great demands on effective models on video encoding and also for reducing the transmission channel congestion. This research work introduces a managing technique termed weighted encoding for High-Efficiency Video Coding (HEVC). HEVC, also termed as MPEG-H Part 2 and H.265 is a video compression standard that is widely utilized AVC (H.264 or MPEG-4 Part 10). When compared to AVC, HEVC grants double the ratio of data compression at a similar level of quality of the video or considerably enhanced video quality at a similar bit rate. This work intends to optimize the weight that adopted in HEVC for encoding. For this, this paper proposes a new Iterative based propagation update in the water wave Optimization Algorithm (IPU-WWO), which is the improved form of Water wave Optimization (WWO). The performance of proposed IPU-WWO is compared over other conventional methods like Artificial Bee Colony (ABC), Firefly (FF), Particle Swarm Optimization (PSO) and Genetic Algorithm (GA) with respect to Peak Signal to Noise Ratio (PSNR). By doing the encoding process, it minimizes the video size with perceptually better quality video or PSNR.     

Demonstration of a tool for automatic learning and re-use of knowledge in the activated sludge process.

Wastewater treatment plant operators encounter complex operational problems related to the activated sludge process and usually respond to these by applying their own intuition and by taking advantage of what they have learnt from past experiences of similar problems. However, previous process experiences are not easy to integrate in numerical control, and new tools must be developed to enable re-use of plant operating experience. The aim of this paper is to investigate the usefulness of a case-based reasoning (CBR) approach to apply learning and re-use of knowledge gained during past incidents to confront actual complex problems through the IWA/COST Benchmark protocol. A case study shows that the proposed CBR system achieves a significant improvement of the benchmark plant performance when facing a high-flow event disturbance.     

Benchmark simulation Model no 2 in Matlab-simulink: towards plant-wide WWTP control strategy evaluation.

In this paper, implementation of the Benchmark Simulation Model No 2 (BSM2) within Matlab-Simulink is presented. The BSM2 is developed for plant-wide WWTP control strategy evaluation on a long-term basis. It consists of a pre-treatment process, an activated sludge process and sludge treatment processes. Extended evaluation criteria are proposed for plant-wide control strategy assessment. Default open-loop and closed-loop strategies are also proposed to be used as references with which to compare other control strategies. Simulations indicate that the BM2 is an appropriate tool for plant-wide control strategy evaluation.     

Optimizing the tapping regime on a blast furnace operating at variable speed

The main factors that determine the uniformity with which smelting products are tapped from a blast furnace are the rate of accumulation of the products in the hearth and the tapping rate. The first parameter is in turn determined by the stability of the furnace’s operation and can vary significantly even over the course of 24 h. The second parameter is determined mainly by the condition of the iron notch, the maintenance it receives, any changes that occur in the diameter of the channel of the notch, and the quality of the materials used to form the notch. Recommendations are presented to optimize tapping of the smelting products.     

On the problem of hydrogen removal during heat treatment of large forgings

The solutions to a differential equation for the problem of heating of a cylinder in a medium with a fixed temperature are used to obtain equations for estimating the change in the hydrogen concentration in forgings from data on the hydrogen concentration at the cylinder axis or on the average bulk hydrogen concentration. Similar equations are also obtained for forgings having square cross sections. The calculation demonstrates that, for the case of a twofold decrease in the hydrogen concentration in a forging, the calculated times of annealing of a cylindrical forging differ by three times.     

Volumetric out-of-furnace heat treatment of 3600-M3 decomposers

Specifications require that all the welds in 12-m-diam. decomposers with a capacity of 3600 m³ be subjected to high-temperature tempering before going into service in order to alleviate the stresses from the welding operation. Specialists at the organizations VNIIPTkhimnefteapparatury and VNIImontazhspetsstroi have proposed out-of-furnace volumetric (complete) of the assembled decomposer with the use of special heaters. The use of this heating method has shortened assembly operations while providing the welds with a highquality heat treatment and reducing the stresses overall (including welding stresses, stresses from assembly of the decomposer, etc.) The technology ensures uniform heating of the housing of the decomposer and provides for close control over the process. The experience gained in heat-treating decomposers can also be used in the construction of other containers that come into contact with corrosive media. __________ Translated from Metallurg, No. 3, pp. 61–64, March, 2006.     

Convergence and trust in eCommerce

Trust is the key element of commerce, both for traditional models and — more recently — for eCommerce. Unlike its traditional counterpart, eCommerce relies on trust being created and maintained with the help of digital devices and services. Convergence brings significant changes to the way people interact through digital media by offering ubiquitous and seamless communication. This has a significant impact on the way trust is established and maintained, with consequent impact upon eCommerce. This paper identifies a number of the most important challenges to trust in eCommerce as well as trust-related aspects of key enablers of eCommerce. From this perspective, the paper studies an impact of convergence on trust within eCommerce to identify several positive relationships.