Enhancing urban infrastructure investment planning practices for a changing climate.

Climate change raises many concerns for urban water management because of the effects on all aspects of the hydrological cycle. Urban water infrastructure has traditionally been designed using historical observations and assuming stationary climatic conditions. The capability of this infrastructure, whether for storm-water drainage, or water supply, may be over- or under-designed for future climatic conditions. In particular, changes in the frequency and intensity of extreme rainfall events will have the most acute effect on storm-water drainage systems. Therefore, it is necessary to take future climatic conditions into consideration in engineering designs in order to enhance water infrastructure investment planning practices in a long time horizon. This paper provides the initial results of a study that is examining ways to enhance urban infrastructure investment planning practices against changes in hydrologic regimes for a changing climate. Design storms and intensity-duration-frequency curves that are used in the engineering design of storm-water drainage systems are developed under future climatic conditions by empirically adjusting the general circulation model output, and using the Gumbel distribution and the Chicago method. Simulations are then performed on an existing storm-water drainage system from NE Calgary to investigate the resiliency of the system under climate change.     

Ecophysiology and niche differentiation of Nitrospira-like bacteria, the key nitrite oxidizers in wastewater treatment plants.

Nitrite-oxidizing bacteria of the genus Nitrospira are key nitrifiers in wastewater treatment plants. Pure cultures of these organisms are unavailable, but cultivation-independent molecular methods make it possible to detect Nitrospira-like bacteria in environmental samples and to investigate their ecophysiology. Comprehensive screening of natural and engineered habitats and of public databases for 16S rRNA sequences of Nitrospira-like bacteria revealed a surprisingly high biodiversity in the genus Nitrospira, which comprises at least four phylogenetic sublineages. All Nitrospira-like bacteria detected in wastewater treatment plants belonged to the sublineages I and II. Subsequently, the population dynamics of different Nitrospira-like bacteria were monitored, by quantitative fluorescence in situ hybridization with rRNA-targeted probes, confocal laser scanning microscopy and digital image analysis, during incubation of nitrifying activated sludge in media containing different nitrite concentrations. These experiments showed that Nitrospira-like bacteria, which were affiliated with the phylogenetic sublineages I or II of the genus Nitrospira, responded differently to nitrite concentration shifts. Previously unknown properties of Nitrospira-like bacteria were discovered in the course of an environmental genomics project. Implications of the obtained results for fundamental understanding of the microbial ecology of nitrite oxidizers as well as for future improvement of nutrient removal in wastewater treatment plants are discussed.     

Using decision analysis to determine optimal experimental design for monitoring sewer exfiltration with tracers.

The tracer methods developed to assess exfiltration from sewers in the European project APUSS (assessment of the performance of sewer systems) have a high degree of freedom with regard to the choice of tracer and the dosing strategy. These can lead to very different degrees of uncertainty in the measured exfiltration ratio. In this study, we demonstrate how to select an optimal experimental design using decision analysis, which accounts for this uncertainty and its associated costs. Although the results are site-specific, we can conclude generally that, when NaCl is used as the tracer, the accuracy of the exfiltration estimate is most sensitive to the amount of tracer used and the starting time of the experiment.     

One-dimensional GIS-based model compared with a two-dimensional model in urban floods simulation.

A GIS-based one-dimensional flood simulation model is presented and applied to the centre of the city of N?mes (Gard, France), for mapping flow depths or velocities in the streets network. The geometry of the one-dimensional elements is derived from the Digital Elevation Model (DEM). The flow is routed from one element to the next using the kinematic wave approximation. At the crossroads, the flows in the downstream branches are computed using a conceptual scheme. This scheme was previously designed to fit Y-shaped pipes junctions, and has been modified here to fit X-shaped crossroads. The results were compared with the results of a two-dimensional hydrodynamic model based on the full shallow water equations. The comparison shows that good agreements can be found in the steepest streets of the study zone, but differences may be important in the other streets. Some reasons that can explain the differences between the two models are given and some research possibilities are proposed.     

Optimizing the tapping regime on a blast furnace operating at variable speed

The main factors that determine the uniformity with which smelting products are tapped from a blast furnace are the rate of accumulation of the products in the hearth and the tapping rate. The first parameter is in turn determined by the stability of the furnace’s operation and can vary significantly even over the course of 24 h. The second parameter is determined mainly by the condition of the iron notch, the maintenance it receives, any changes that occur in the diameter of the channel of the notch, and the quality of the materials used to form the notch. Recommendations are presented to optimize tapping of the smelting products.     

On the problem of hydrogen removal during heat treatment of large forgings

The solutions to a differential equation for the problem of heating of a cylinder in a medium with a fixed temperature are used to obtain equations for estimating the change in the hydrogen concentration in forgings from data on the hydrogen concentration at the cylinder axis or on the average bulk hydrogen concentration. Similar equations are also obtained for forgings having square cross sections. The calculation demonstrates that, for the case of a twofold decrease in the hydrogen concentration in a forging, the calculated times of annealing of a cylindrical forging differ by three times.     

An element-based displacement preconditioner for linear elasticity problems

Finite element analysis of problems in structural and geotechnical engineering results in linear systems where the unknowns are displacements and rotations at nodes. Although the solution of these systems can be carried out using either direct or iterative methods, in practice the matrices involved are usually very large and sparse (particularly for 3D problems) so an iterative approach is often advantageous in terms of both computational time and memory requirements. This memory saving can be further enhanced if the method used does not require assembly of the full coefficient matrix during the solution procedure. One disadvantage of iterative methods is the need to apply preconditioning to improve convergence. In this paper, we review a range of established element-based preconditioning methods for linear elastic problems and compare their performance with a new method based on preconditioning with element displacement components. This new method appears to offer a significant improvement in performance.     

Reliable eye-diagram analysis of data links via device macromodels

This paper addresses the impact of device macromodels on the accuracy of signal integrity and performance predictions for critical digital interconnecting systems. It exploits nonlinear parametric models for both single-ended and differential devices, including the effects of power supply fluctuations and receiver bit detection. The analysis demonstrates that the use of well-designed macromodels dramatically speeds up the simulation as well it preserves timing accuracy even for long bit sequences.     

On-line estimation of kinetic parameters in anaerobic digestion using observer-based estimators and multiwavelength fluorometry.

Observer-based estimators (OBE) were used for estimation of state variables and kinetic parameters in an anaerobic digestion (AD) process. A simplified first-order model with time-varying kinetic parameters was used to design an OBE for kinetic parameter estimation. This approach was validated on a laboratory-scale anaerobic reactor equipped with a multiwavelength fluorometer for on-line measurements of COD and VFA concentrations in the reactor effluent. The proposed estimators provide continuous adjustment of kinetic parameters and can be used for predictions of state variables between samples acquisition and during sensor failure.     

Optimal control of the effects from industrial transportation on the environment

The paper discusses optimal control of ecosystem state for observation of a generalized monotonically varying random parameter. A model is proposed for the controlled vector random process, whose components are assigned acceptable ranges and the observations are performed discretely. __________ Translated from Khimicheskoe i Neftegazovoe Mashinostroenie, No. 6, pp. 40–44, June, 2006.