Synthesis of thermoresponsive copolymer/silica-coated magnetite nanoparticle composite and its application for heavy metal ion recovery

To enhance chemical stability and suppress of aggregation of magnetite nanoparticles (MNPs), which are used as a support for thermoresponsive copolymer immobilization, silica coating of the MNPs is applied via the electrooxidation method. Although the resulting silica coated-MNPs also formed aggregates, the size distribution of the aggregate shifted to smaller size range. Because of that, the surface area available for copolymer immobilization increased approximately 6.7 times at maximum as compared with that of the uncoated MNPs. It contributed to the increase of the amount of the immobilized copolymer on the silica-coated MNPs, which is approximately four times larger than that on the uncoated MNPs. Fe₃O₄ dissolution test confirmed enhancement of chemical stability of MNPs. The thermoresponsive copolymer immobilized on the silica-coated MNPs shows the ability to recycle Cu(II) ion from Cu(II) containing solution by changing temperature with significantly shorter time than those in other thermoresponsive adsorbents in gel form.     

A CMOS multichannel 10-Gb/s transceiver

We describe a CMOS multichannel transceiver that transmits and receives 10 Gb/s per channel over balanced copper media. The transceiver consists of two identical 10-Gb/s modules. Each module operates off a single 1.2-V supply and has a single 5-GHz phase-locked loop to supply a reference clock to two transmitter (Tx) channels and two receiver (Rx) channels. To track the input-signal phase, the Rx channel has a clock recovery unit (CRU), which uses a phase-interpolator-based timing generator and digital loop filter. The CRU can adjust the recovered clock phase with a resolution of 1.56 ps. Two sets of two-channel transceiver units were fabricated in 0.11-/spl mu/m CMOS on a single test chip. The transceiver unit size was 1.6 mm /spl times/ 2.6 mm. The Rx sensitivity was 120-mVp-p differential with a 70-ps phase margin for a common-mode voltage ranging from 0.6 to 1.0 V. The evaluated jitter tolerance curve met the OC-192 specification.     

Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Monte Carlo simulation of hydrogen absorption in palladium and palladium–silver alloys

A modified Monte Carlo (MC) simulation was performed to investigate the hydrogen absorption behavior in Pd and Pd–Ag alloys of the composition Pd_xAg_1−x (x=0.7–0.8) under H₂ pressure (0.1 MPa) at different temperatures. The present method employed can consider the dissociative adsorption of hydrogen molecule and the subsequent absorption of hydrogen atom by formalizing the relationship between the pressure of hydrogen molecule and hydrogen atom. The potential parameters were determined to reproduce the solution enthalpy of hydrogen in pure metals. The results are in good agreement with experimental findings as well as previous theoretical studies. We confirmed that our method is useful to simulate the absorption of hydrogen in metals and alloys.     

Experimental study of venous circulatory disturbance by dural sinus occlusion

Using a newly devised model of dural sinus occlusion, we investigated the pathophysiology of venous haemorrhage as well as venous circulatory disturbance. The superior sagittal sinus (SSS) and diploic veins (DV) were occluded in 16 cats. Intracranial pressure (ICP), cerebral blood volume (CBV) and regional cerebral blood flow (rCBF) were measured for 12 hours after the occlusion. At the end of the experiment, cerebral water content was estimated. In another 8 cats additional occlusions of cortical veins were carried out. In both groups, the blood-brain barrier permeability was evaluated with Evans blue or horseradish peroxidase. The SSS and DV occlusion produced a significant increase in ICP and CBV concomitant with a significant decrease in rCBF. Cerebral water content also increased significantly. However, there was no transition of Evans blue and horseradish peroxidase through the cerebral vessels, and no haemorrhages could be observed. In contrast, the additional occlusion of cortical veins produced haemorrhagic infarctions with Evans blue extravasation in 6 out of the 8 cats. These data suggest that dural sinus occlusion may lead to an increase in CBV and cerebral water content resulting in intracranial hypertension and decreased rCBF. The brain oedema in this model seemed to be mainly hydrostatic oedema, and might also be contributed by cytotoxic oedema. The additional occlusion of cortical veins might be essential in the development of haemorrhage in this model, and the blood-brain barrier was also disrupted in these areas.     

Damage tolerance of glass mat/epoxy laminates hybridized with flexible resin under static and impact loading

This study deals with the impact property and damage tolerance of matrix hybrid composite laminates with different laminate constitution. The matrix hybrid composite laminates consisted of the laminae with a conventional epoxy resin and the laminae with a flexible epoxy resin modified from the conventional resin to avoid the interlaminar delamination. The impact energy absorption ratio greatly depended on the matrix resin placed at the impact face. The energy absorption was almost constant if the conventional resin was placed at the impact surface layer, while it increased exponentially with the increasing fraction of the flexible resin if the flexible resin was placed at the impact face. The impact energy was absorbed by the damage development and propagation in the laminate with conventional resin laminae as the impacted face, while it was absorbed by both the recoverable deformation of the flexible resin and the damage propagation in the laminate with flexible resin laminae as the impacted face.     

Au/Pt/Ti/Ni ohmic contacts to p-ZnTe

Ohmic contacts of Au/Pd/Ti/Ni to p-ZnTe show a minimum specific contact resistance of 10^-6 Ωcm² for a p-type doping level of 3×10¹⁹ cm^-3 and at an annealing temperature of 300°C. The Ni and Ti layers are very effective in improving the electrical properties of these contact     

A semi-static complementary gain cell technology for sub-1 V supplyDRAM's

A new semi-static complementary gain cell for future low power DRAM's has been proposed and experimentally demonstrated. This gain cell consists of a write-transistor and its opposite conduction type read-transistor with a heating gate as a storage node which causes a shift in the threshold voltage. This gain cell provides a two orders of magnitude larger cell signal output and higher immunity to noise on the bitlines when compared with a conventional one-transistor DRAM cell without increasing the storage capacitance even at a supply voltage of 0.8 V. The 0.87 μm² cell size is achieved by using a 0.25 μm design rule with a polysilicon thin-film transistor built in the trench and phase shifted i-line lithography     

Surface Hardening of Carbon Steel Using High Powered YAG Laser

A high powered YAG laser with kaleidoscope for surface modification was applied to the surface hardening of carbon steels containing 0. 18-0.54 wt% C without the absorbents, and the relationships between laser processing and surface hardening were investigated by hardness and microstructure. The structure of the hardened zone underwent complete martensitic transformation in all of the carbon steels tested, and its hardness increased with greater carbon content. Under identical irradiated conditions, the hardened zone expanded with increasing carbon content. A hardened zone extending from the surface to a depth of 1.0 mm was obtained at a laser power of 1.0 kW and a scanning speed of 1 mm/sec. It was found that in the surface hardening of carbon steels, a high powered YAG laser can be used to control the hardened zone by selecting the appropriate irradiation conditions, however, the hardened zone was affected by the assistant gas and the flow rate.