吸湿凉爽机织物的结构设计与性能

为研究织物组织结构与复合纱线线密度对织物凉爽性能的影响,将线密度为7.4和9.8 tex涤纶分别与线密度为7.8 tex锦纶反向加捻、并线后作为纬纱,以8.3 tex涤纶/竹浆纤维50/50混纺纱作经纱,设计平纹、二上一下斜纹和透孔组织织物.测试织物的瞬间接触凉感、热湿舒适性能及织物干、湿态升温曲线,并采用凉爽温度指数对织物的综合凉爽性能进行评价.研究结果表明:6种设计织物的瞬间接触凉感均高于标准,且平纹织物最好,纬纱粗细对瞬间接触凉感影响不显著;透孔织物透气性最好,且在人体出汗的状态下具有较好的导湿散热性能.平纹织物凉爽温度指数最高,最大凉爽温度为2.8℃,综合凉爽性能最好.     

A novel InP/InGaAs TEBT for ultralow current operations

A novel InP/InGaAs tunneling emitter bipolar transistor (TEBT) is fabricated and demonstrated. The studied device exhibits a very small collector-emitter offset voltage of 40 mV and an extremely wide operation regime. The operation region is larger than 11 decades in magnitude of collector current (10/sup -12/ to 10/sup -1/A). A current gain of 3 is obtained even if the device is operated at an ultralow collector current of 3.9 /spl times/ 10/sup -12/A (1.56 /spl times/ 10/sup -7/A/cm/sup 2/). Furthermore, the common-emitter breakdown voltage of the studied device is higher than 2 V. Consequently, the studied device shows a promise for low supply voltage, and low-power consumption circuit applications.     

A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method     

A general framework for debugging

The state of the art of debugging is examined. A debugged process model that serves as the basis of a general debugging framework is described. The relationship of the model to traditional debugging processes and support tools is discussed. A minimal set of requirements for a general debugging framework is described in terms of both the theory behind debugging methodologies and the support tools. An execution monitor, Eden, that serves as a debugging tool within this general framework is described     

Online and Offline Rotary Regression Analysis of Torque Estimator for Switched Reluctance Motor Drives

A new torque estimator for switched reluctance motor (SRM) drives based on 2-D rotary regression analysis is presented in this paper. The proposed torque estimator is composed of a bicubic regressive polynomial as a function of rotor position and input current. The regressive coefficients can be computed offline or online from the torque characteristics acquired either experimentally or from numerical computation. Furthermore, a torque estimation method by taking mutual coupling into consideration is proposed. It can be seen that the estimated and experimentally obtained self-coupling and mutual-coupling torque characteristics are in good agreement with each other. In addition, the dynamic torque waveforms with and without the mutual coupling, estimated by the proposed estimator, are found to be virtually the same as those obtained from the bicubic spline interpolation for SRM drives with single-pulse voltage, hysteresis current chopping, as well as with voltage pulse width modulation control. The success of all the case studies being reported is a good validation of the usefulness and accuracy of the proposed real-time torque estimator that, as described in this paper, can be used to quickly estimate the instantaneous output torque of SRM drives.     

Enhanced electron emission from phosphorus-doped diamond-cladsilicon field emitter arrays

Undoped and phosphorus (P)-doped diamond-clad Si field emitter arrays have been successfully fabricated using microwave plasma chemical vapor deposition (MPCVD) technology. The electron emission from the blunt diamond-clad microtips are much higher than those for the pure Si tips with sharp curvature due to a lower work function. Furthermore, the characteristics of emission current against applied voltage for the P-doped diamond-clad tips show superior emission at lower field to the undoped ones. After the examination of Auger electron spectroscopy (AES) and electrical characteristics of as-grown diamond, such a significant enhancement of the electron emission from the P-doped diamond-clad tips is attributed to a higher electron conductivity and defect densities     

Configurable nonlinear filter generator

A configurable nonlinear filter generator is proposed. The nonlinear function employed is key controllable. By changing the key, a different sequence will be obtained. Simulated results show that an optimal linear complexity profile of the sequence can be generated     

Simple approximations of the DC flux influence on the core losspower electronic ferrites and their use in design of magnetic components

The effect of DC flux on the core loss is examined for the practical range of power and frequency. Relevant core loss equations are derived and applied to an optimization algorithm to determine the minimum core loss at a given ratio of s (DC flux density to AC peak flux density). It has been found that the curves of hysteresis loss density versus the ratio of s exhibit a peak at a critical ratio. Below or above this critical ratio, the loss density decreases drastically. On the other hand, the curves of eddy-current loss density versus the ratio of s exhibits a minimum point at a critical ratio. Below or above this critical ratio, the loss density increases gradually     

A Petri net based approach to modeling and scheduling for an FMSand a case study

In this paper, a timed-place Petri net (TPPN) model for flexible manufacturing systems (FMSs) is constructed, which contains two major submodels: the stationary transportation model; and the variable process flow model. For multiple automated guided vehicle (AGV) systems, the authors embed a simple rule and introduce a push-AGV strategy in a TPPN model to solve the collision and traffic jam problems of such vehicles. Since a firing sequence of the TPPN from the initial marking to the final marking can be seen as a schedule of the modeled FMS, by using an A^* based search algorithm, namely, the limited-expansion A algorithm, an effective schedule of the part processing can be obtained. To show the promising potential of the proposed work, a prototype FMS is used as a target system for implementation. The experiment results assert that the job-shop scheduling problem can always be satisfactorily solved     

Suppression of boron penetration in p+ polysilicon gateP-MOSFETs using low-temperature gate-oxide N2O anneal

It has been reported that high-temperature (~1100°C) N₂ O-annealed oxide can block boron penetration from poly-Si gates to the silicon substrate. However, this high-temperature step may be inappropriate for the low thermal budgets required of deep-submicron ULSI MOSFETs. Low-temperature (900~950°C) N₂O-annealed gate oxide is also a good barrier to boron penetration. For the first time, the change in channel doping profile due to compensation of arsenic and boron ionized impurities was resolved using MOS C-V measurement techniques. It was found that the higher the nitrogen concentration incorporated at Si/SiO₂ interface, the more effective is the suppression of boron penetration. The experimental results also suggest that, for 60~110 Å gate oxides, a certain amount of nitrogen (~2.2%) incorporated near the Si/SiO₂ interface is essential to effectively prevent boron diffusing into the underlying silicon substrate