Eco-friendly and degradable red phosphorus nanoparticles for rapid microbial sterilization under visible light

Pathogens pose a serious challenge to environmental sanitation and a threat to public health.The frequent use of chemicals for sterilization in recent years has not only caused secondary damage to the environment but also increased pathogen resistance to drugs,which further threatens public health.To address this issue,the use of non-chemical antibacterial means has become a new trend for environmental disinfection.In this study,we developed red phosphorus nanoparticles(RPNPs),a safe and degradable photosensitive material with good photocatalytic and photothermal properties.The red phosphorus nanoparticles were prepared using a template method and ultrasonication.Under the irradiation of simulated sunlight for 20 min,the RPNPs exhibited an efficiency of 99.98%in killing Staphylococcus aureus due to their excellent photocatalytic and photothermal abilities.Transmission electron microscopy and ultraviolet–visible spectroscopy revealed that the RPNPs exhibited degradability within eight weeks.Both the RPNPs and their degradation products were nontoxic to fibroblast cells.Therefore,such RPNPs are expected to be used as a new type of low-cost,efficient,degradable,biocompatible,and eco-friendly photosensitive material for environmental disinfection.     

Dense and core-rim structured B4C-TiB2 ceramics with Mo-Co-WC additive

B₄C-TiB₂ ceramics (TiB₂ ranging 5~70 vol%) with Mo-Co-WC as the sintering additive were prepared by spark plasma sintering. In comparison with B₄C-TiB₂ without additive, the enhanced densification was evident in the sintered specimen with Mo-Co-WC additive. Core-rim structured grain was observed around TiB₂ grains. The interface of the rim between TiB₂ and B₄C phases demonstrated different feature: the inner borderline of the rim exhibited a smooth feature, whereas a sharp curved grain boundary was observed between the rim and the B₄C grain. The formation mechanism is discussed: the epitaxial growth of (Ti,Mo,W)B₂ rim around the TiB₂ core may occur as a result of the solid solution and dissolution-precipitation between TiB₂ phase and the sintering additive. It was revealed that the fracture toughness increased as the content of TiB₂ content increased, alongside the decreased hardness. B₄C-30 vol% TiB₂ specimen demonstrated the optimal combination of mechanical properties, reaching Vickers hardness of 24.3 GPa and fracture toughness of 3.33 MPa·m^1/2.     

中药桂枝总黄酮的提取工艺研究

优化桂枝总黄酮的提取工艺，建立桂枝的提取和含量测定方法。通过单因素试验，考察提取方法、提取溶剂浓度、提取体积、提取时间对药材总黄酮含量的影响，采用正交试验，优化提取工艺条件，筛选出桂枝总黄酮的最佳提取工艺。总黄酮最佳提取工艺为75%乙醇、料液比1:40、回流提取时间60 min。该方法能有效测定桂枝药材总黄酮的含量，为该药材的质量标准研究提供一定的科学依据。本方法重复性较好、方法稳定、可行。     

面向医院建筑项目的IPD模式应用研究

医院建筑项目是非常复杂且具有挑战性的建设项目。传统的交付模式无法满足人们对医院建筑建设、运营方面的高要求,为此开展面向医院建筑项目的IPD模式应用研究。在对IPD模式发展现状整理的基础上,阐述医院建筑项目IPD模式的适用性。分析采用IPD模式的医院建筑项目特点,并以上海市某公立三甲专科医院项目为例,对IPD模式在国内的应用进行探索性研究。     

Integral barrier Lyapunov function-based adaptive fuzzy output feedback control for nonlinear delayed systems with time-varying full-state constraints

In this article, an adaptive fuzzy output feedback control method is presented for nonlinear time-delay systems with time-varying full state constraints and input saturation. To overcome the problem of time-varying constraints, the integral barrier Lyapunov functions (IBLFs) integrating with dynamic surface control (DSC) are applied for the first time to keep the state from violating constraints. The effects of unknown time delays can be removed by using designed Lyapunov-Krasovskii functions (LKFs). An auxiliary design system is introduced to solve the problem of input saturation. The unknown nonlinear functions are approximated by the fuzzy logic systems (FLS), and the unmeasured states are estimated by a designed fuzzy observer. The novel controller can guarantee that all signals remain semiglobally uniformly ultimately bounded and satisfactory tracking performance is achieved. Finally, two simulation examples illustrate the effectiveness of the presented control methods.     

Cell-Free Synthesis of Selenoproteins in High Yield and Purity for Selective Protein Tagging

The selenol group of selenocysteine is much more nucleophilic than the thiol group of cysteine. Selenocysteine residues in proteins thus offer reactive points for rapid post-translational modification. Herein, we show that selenoproteins can be expressed in high yield and purity by cell-free protein synthesis by global substitution of cysteine by selenocysteine. Complete alkylation of solvent-exposed selenocysteine residues was achieved in 10 minutes with 4-chloromethylene dipicolinic acid (4Cl-MDPA) under conditions that left cysteine residues unchanged even after overnight incubation. Gd^III−Gd^III distances measured by double electron–electron resonance (DEER) experiments of maltose binding protein (MBP) containing two selenocysteine residues tagged with 4Cl-MDPA-Gd^III were indistinguishable from Gd^III−Gd^III distances measured of MBP containing cysteine reacted with 4Br-MDPA tags.     

锚栓用量对纯锚固岩棉保温系统抗风压性能的影响

采用ETAG 004:2013《外墙外保温薄抹灰系统欧洲技术认证指南》中规定的静态泡沫块法,测试在单位面积上使用不同数量锚栓的岩棉板外保温系统的抗风压性能。通过试验可以得出:在混凝土墙体上单纯采用敲击式锚栓锚固岩棉板外保温系统时,拉伸强度可达12.9 k Pa;单位面积增加锚栓的使用量可以提高系统的抗拉承载力,但在不同条件下增加相同数量锚栓对系统抗风载能力提高的程度不同;在普通混凝土墙中,单纯锚固岩棉板保温系统破坏时,单个锚栓承载力平均值的最大值约为其拉拔承载力的50.3%。     

智能站设计在变电二次继电保护中的作用

分析了智能站设计在变电二次机电保护过程中的重要作用,探讨了智能站设计的主要概念以及变电站二次机电保护的主要过程,并分析了智能站设计的相关要素,提出了智能站设计的主要对策和相关注意事项.希望能够为相关工作人员开展智能站设计工作起到一些参考和借鉴作用,从而进一步提升我国变电站二次继电保护水平,保障相关供电系统的安全运行,促进我国电力事业的快速发展.     

Corrosion of hot-dip-galvanised steel and zinc alloy-coated steel in ammonia and ammonium chloride

There are many potential causes of corrosion in animal buildings. Animals exhale large quantities of moisture into the air creating high relative humidity in the building if the moisture is not properly vented. High humidity increases the potential for condensation. In addition, ammonia may be found in large quantities in animal buildings. Ammonia is released from manure and urine. In addition, ammonium chloride is used as a nitrogen source in fertilisers. In this study, the atmospheric corrosion of hot-dip-galvanised steel and zinc alloy-coated steel such as zinc–aluminium and zinc–aluminium–magnesium has been studied in atmospheres containing different levels of ammonia. Investigations have also been conducted at different levels of ammonium chloride. The results are discussed in view of the mechanisms of corrosion of zinc and zinc alloy-coated steel in ammonia and ammonium chloride-containing environments.