吸湿凉爽机织物的结构设计与性能

为研究织物组织结构与复合纱线线密度对织物凉爽性能的影响,将线密度为7.4和9.8 tex涤纶分别与线密度为7.8 tex锦纶反向加捻、并线后作为纬纱,以8.3 tex涤纶/竹浆纤维50/50混纺纱作经纱,设计平纹、二上一下斜纹和透孔组织织物.测试织物的瞬间接触凉感、热湿舒适性能及织物干、湿态升温曲线,并采用凉爽温度指数对织物的综合凉爽性能进行评价.研究结果表明:6种设计织物的瞬间接触凉感均高于标准,且平纹织物最好,纬纱粗细对瞬间接触凉感影响不显著;透孔织物透气性最好,且在人体出汗的状态下具有较好的导湿散热性能.平纹织物凉爽温度指数最高,最大凉爽温度为2.8℃,综合凉爽性能最好.     

无机高分子絮凝剂聚硫酸铁合成条件的研究

实验研究了以工业硫酸亚铁及废硫酸为原料,分别采用NaClo_3、KClO_3、H_2O_2及(o_2+NaNO_2)为氧化剂成聚硫酸铁的条件。在以(O_2+NaNO_2)为氧化剂的合成过程中,发现添加微量助催化剂(型号为HG-1、HG-2和HG-3),对提高合成速度及反应过程的稳定性具有重大作用。     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

高柔韧性尼龙1010材料的制备

对尼龙1010/NBR/增塑剂体系进行了系统研究,发现在挤出机中环氧扩链剂可以对尼龙进行扩链反应,且环氧树脂对尼龙1010的扩链反应活性较高,扩链效果比较明显;N-丁基苯磺酰胺是尼龙的良好增塑剂,经增塑、增韧后可以使经扩链后的尼龙1010柔韧性有明显提高.采用SEM和TEM对所制备的材料进行了形貌分析,发现用NBR增韧尼龙,对于不同的基体材料,橡胶粒子的形貌有很大不同,粒子由增韧纯尼龙的椭球形变为在增塑尼龙基体中不规则的形状.     

逆向工程技术在机械领域的应用

逆向工程技术已成为联系新产品开发过程中各种先进技术的纽带,并成为实现新产品快速开发的重要技术手段.介绍了逆向工程的概念、技术流程、测量系统、常用软件以及实际应用.     

Studies on the microstructure of the black-glazed bowl sherds excavated from the Jian kiln site of ancient China

The Jian kiln, located in present-day Jianyang county of Fujian province, mainly produced black-glazed tea bowls. Jian tea bowl was used as a utensil for tea tasting and was greatly appreciated by emperor Huizong of the Northern Song dynasty. The black glaze of Jian bowl was sometimes marked with streaks or spots, usually called “hare's fur” or “oil spot”, which are the crystalline markings of iron oxide precipitated during firing in the dragon kiln. In this study, black-glazed Jian bowl sherds excavated from the late Northern Song strata of Luhuaping and Daluhoumen Jian kiln sites were adopted as test samples. Based on the physico-chemical foundation for the formation of glaze microstructure, the correlation among composition, microstructure, and visual appearance has been investigated by means of energy-dispersive X-ray fluorescence, X-ray diffraction, and field emission electron microscopy. For the first time, the study provides realizing proofs for two kinds of microstructural forming mechanics.     

Local residence time,residence revolution,and residence volume distributions in twin‐screw extruders

This work was aimed at studying the overall, partial, and local residence time distributions (RTD); overall, partial and local residence revolution distributions (RRD) and overall, partial and local residence volume distributions (RVD) in a co‐rotating twin screw extruder, on the one hand; and establishing the relationships among them, on the other hand. Emphasis was placed on the effects of the type and geometry of mixing elements (a gear block and various types of kneading elements differing in staggering angle) and process parameters on the RTD, RRD and RVD. The overall and partial RTD were directly measured in‐line during the extrusion process and the local ones were calculated by deconvolution based on a statistical theory. The local RTD allowed comparing the mixing performance of mixing elements. Also it was confirmed both experimentally and theoretically that specific throughput, defined as a ratio of throughput (Q) over screw speed (N), controlled all the above three types of residence distributions, be they local, partial or overall. The RRD and RVD do not provide more information on an extrusion process than the corresponding RTD. Rather they are different ways of representing the same phenomena. POLYM. ENG. SCI., 48:19–28, 2008. © 2007 Society of Plastics Engineers