Analysis of brushless three-phase synchronous generator without exciter

Recently, a demand for small-capacity generators has been increasing as electric sources in small ships and automobiles or as portable electric sources driven by engines. It is desired that the structure of small-capacity generators be simple and robust, and that the generators be highly reliable, easily maintained and controlled. This paper describes an analysis of the original brushless synchronous generator without exciter. The output voltage can be adjusted in the wide range by controlling the stator dc current. To analyze the characteristics of this generator, the finite element method is applied. It is found that the results of theoretical analysis agree well with the experimental results.     

Case performed: simultaneous surgery for left coronary ostial stenosis and gastric cancer

This report describes a case in which a 68-year-old male underwent two operations simultaneously for left coronary ostial stenosis and gastric cancer. Successfully performed procedures were a single coronary artery grafting with the saphenous vein to the left anterior descending artery, and a subtotal gastrectomy using the Billroth II method. The postoperative course was uneventful and the patient was discharged from the hospital in good condition after 42 days. At present, one-year postoperative, the patient has been visiting the outpatient clinic in healthy condition.     

Silica removal from Mokai, New Zealand, geothermal brine by treatment with lime and a cationic precipitant

Preliminary experiments using two chemicals (CaO, a quicklime, and a cationic nitrogen-bearing precipitant, EC-004) to remove silica from geothermal brine were undertaken at the Mokai geothermal plant, New Zealand. The brine was mixed with the reagent (CaO or EC-004). The reaction was studied from the start of the experiment (NRT, 0 min, no retaining time) and after 15 min (15RT) at 90 °C. The concentration of silica in the brine was initially 954 mg/l, and decreased linearly with increasing reagent concentration. When CaO is added, the silica concentration at 15RT was 200 mg/l lower than at NRT and became almost zero on addition of 1.5 g/l. In contrast, when EC-004 is added, the total silica concentration nearly reaches the solubility of amorphous silica at 90 °C. In order to prevent silica scaling in Mokai brines cooled to 90 °C, the CaO and EC-004 added should be individually adjusted to 0.5 g/l and 80 mg/l, respectively.     

Steady-state torque control system with secondary-current feedback for three-phase squirrel-cage induction motors

This paper presents a highly stable steady-state torque control system with a feedback of a secondary current signal. The torque control system is constructed with a feedback of the secondary current (I₂) signal using a quick response magnetic-field sensor constructed with an amorphous core multivibrator bridge, which can solve the secondary resistance change problem for temperature variation in the IM. Moreover, we added a state feedback to the system to improve the response speed for the unit step function of a torque order. The I₂ sensor method has advantages especially at a low-speed range, in which conventional method using an integrator shows control errors.     

A novel robust current control approach using adaptive line enhancer for three‐phase current‐source active power filter

An effective system control method is presented for applying a three‐phase current‐source PWM converter with a deadbeat controller to active power filters (APFs). In the shunt‐type configuration, the APF is controlled such that the current drawn by the APF from the utility is equal to the current harmonics and reactive current required for the load. To attain the time‐optimal response of the APF supply current, a two‐dimensional deadbeat control scheme is applied to APF current control. Furthermore, in order to cancel both the delay in the two‐dimensional deadbeat control scheme and the delay in DSP control strategy, an Adaptive Line Enhancer (ALE) is introduced in order to predict the desired value three sampling periods ahead. ALE has another function of bringing robustness to the deadbeat control system. Due to the ALE, settling time is made short in a transient state. On the other hand, total harmonic distortion (THD) of source currents can be minimized compared to the case where ideal identification of the controlled system can be made. The experimental results obtained from the DSP‐based APF are also reported. The compensating ability of this APF is very high in accuracy and responsiveness although the modulation frequency is rather low. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20014     

Gel chromism and anomalous luminescence in poly(3-alkylthiophene)

The absorption spectrum of poly(3-alkylthiophene) gel changes drastically in association with a volume instability upon changing the solvent composition and also the temperature. In the expanded state in chloroform and at high temperature, the photoluminescence is much enhanced compared with the shrunken state in ethanol and at low temperature. This gel chromism and anomalous luminescence are discussed in terms of the change of effective conjugation length induced by the steric hindrance and the dynamics of the photoexcited species.     

Fabrication of large-volume microfluidic chamber embedded in glass using three-dimensional femtosecond laser micromachining

We report on fabrication of large-volume, square-shaped microfluidic chamber embedded in glass by scanning a tightly focused femtosecond laser beam inside a porous glass immersed in water. After the hollow structure is created in the porous glass substrate, the fabricated glass sample is post-annealed at 1,050°C during which it can be sintered into a compact glass. By the use of this technique, a 1 mm × 1 mm × 100 μm microchamber connected to four microfluidic channels is created inside the transparent glass substrate, showing that our technique allows for fabrication of not only thin channel structures with arbitrary lengths and configurations, but also hollow structures with infinitely large sizes.     

Brave induction: a logical framework for learning from incomplete information

This paper introduces a novel logical framework for concept-learning called brave induction. Brave induction uses brave inference for induction and is useful for learning from incomplete information. Brave induction is weaker than explanatory induction which is normally used in inductive logic programming, and is stronger than learning from satisfiability, a general setting of concept-learning in clausal logic. We first investigate formal properties of brave induction, then develop an algorithm for computing hypotheses in full clausal theories. Next we extend the framework to induction in nonmonotonic logic programs. We analyze computational complexity of decision problems for induction on propositional theories. Further, we provide examples of problem solving by brave induction in systems biology, requirement engineering, and multiagent negotiation.     

Signal flow graph modelling of interleaved buck converters

This paper presents a systematic development of unified signal flow graph model for an interleaved buck converter system operating in continuous inductor current mode. From this signal flow graph small, large‐signal and steady‐state models are developed, which are useful to study the converter dynamic and steady‐state behaviour. Converter performance expressions like steady‐state voltage gain, efficiency expressions and other small‐signal characteristic transfer functions are derived. Development of unified signal flow graph is explained for a 3‐cell interleaved converter system. Derivation of large, small‐signal and steady‐state models from the unified signal flow graph is demonstrated by considering a 2‐cell interleaved buck converter system. Large signal model was programmed in TUTSIM simulator, and the large‐signal responses against supply, load disturbances were predicted. Signal flow graph analysis results are validated with PSIM simulations. Further, the mathematical models obtained from the signal flow graph modelling are in agreement with those obtained from the state‐space averaging technique. Copyright © 2003 John Wiley & Sons, Ltd.