A New Comb Circular Polarizer Suitable for Millimeter‐Band Application

This letter presents a new polarizer which has a simple comb structure inside a circular waveguide. The electrical performance of the proposed comb polarizer is optimized by a circular waveguide radius and by the physical parameters of the comb plates. This polarizer is suitable for providing good performance in millimeter‐band application because of its simple structure and low fabrication cost. In our experiments the dual‐band comb polarizer designed in band 1(K) and band 2(Ka) showed good electrical performance without any tuning elements.     

合成己二腈反应技术研究——(Ⅴ)己二腈工业反应过程模拟与反应器改造

对己二腈工业反应器提出了两釜串联带回流的模型,通过模拟计算得出模型的级间返混系数 f=6的结论。该模型能较好地预测工业反应器中物料组分浓度变化和气、液两相的流动特性;指出了现工业反应器的鼓泡中和段体积偏小是造成己二酸浓度偏高的关键;提出了可以通过增加串连一个鼓泡预反应段的改造方案,能有效地降低己二酸的浓度,从7%降至4%左右,从而能较好地减缓腐蚀和结焦。     

Enterococcal bacteremia in a medical center

BACKGROUND: The enterococci have become important nosocomial pathogens. They can cause multiple site infections and enterococcal bacteremia becomes more frequently associated with a high mortality rate. Previous studies of enterococcal bacteremia showed a variety of results. To establish the significance and importance of enterococci as nosocomial pathogens in this hospital, to characterize their clinical pictures and to search for the risk factors for mortality, this retrospective study was performed. METHODS: There were 208 cases of enterococcal bacteremia which occurred from 1988 to 1992. Twenty-seven cases had no medical charts, dismissing possibility of evaluation. Finally, 181 cases of enterococcal bacteremia were analysed. RESULTS: One hundred and eighteen episodes were nosocomial infections. Polymicrobial bacteremia occurred in 68.5% of the patients and the most common co-isolate was Pseudomonas aeruginosa. Those patients (78.5%) with underlying diseases and malignancies were the most common underlying problems. The portal of entry could be found in 69.6 percent of patients, with the gastrointestinal tract the most common sources. Antimicrobial susceptibility testing showed high gentamicin resistance rate (89.5%), and ampicillin still had about 80 percent sensitivity rate. The group who received specific antibiotic therapy for enterococcus showed lower mortality (36.4% versus 47.6%). Only one case had infective endocarditis. Forty-nine patients suffered from septic shock, the cause of 30 deaths. Totally 75 patients died during hospitalization. Besides sepsis, another major cause of death was their underlying diseases itself. CONCLUSIONS: Enterococci have no doubt become important nosocomial pathogens and enterococcal bacteremia were associated with high mortality, especially in elderly patients with underlying diseases such as malignancy or diabetes. When clinically dealing with sepsis from the gastrointestinal or biliary tract, especially when previous cephalosporins therapy showed no response, the possibility of enterococcal bacteremia should always be considered.     

A study of CaCO3 fouling with a microscopic imaging technique

The present study introduces a new experimental method to visualize the fouling process of CaCO₃. A mini-channel heat exchanger system with a microscopic imaging technique was developed for real-time visualization of the fouling process. The present study discussed how scale started initially, how scale formed thick layers, and how a small crystal grew into a large one, touching the adjacent one. Detail microscopic images of scale crystals and corresponding fouling resistances were obtained over the entire fouling process. The microscopic observation indicated that the fouling process could be divided into three stages: an induction period, a period of uniform generation of nuclei, and a period of uniform growth of scale. Sudden appearance of numerous small nuclei indicated the end of the induction period, a key event before the rapid increase in the fouling resistance. The present experimental method using microscopic images of the wet fouling process provides a valuable insight on the fouling mechanism.     

Poly(butylene terephthalate)–clay nanocomposites prepared by melt intercalation: morphology and thermomechanical properties

Nanocomposites based on poly(butylene terephthalate) (PBT) and an organoclay (Cloisite 30B) were prepared by melt blending using a twin‐screw extruder. Two kinds of PBTs, ie PBT‐A and PBT‐B, with different inherent viscosities (η_inh), were used for this study (η_inh of PBT‐A and PBT‐B were 0.74 and 1.48, respectively). Dispersion of the clay layers in the PBT nanocomposites was characterized by using X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Tensile and dynamic mechanical properties and non‐isothermal crystallization temperatures of the nanocomposites were also examined. Nanocomposites based on the higher‐viscosity PBT (PBT‐B) showed a higher degree of exfoliation of the clay and a higher reinforcing effect when compared to the composites based on the lower‐viscosity PBT (PBT‐A). The clay nanolayers dispersed in PBT matrices lead to increases in the non‐isothermal crystallization temperatures of the PBTs, with such increases being more significant for the PBT‐B nanocomposites than for the PBT‐A nanoocomposites. Copyright © 2004 Society of Chemical Industry     

Holographic polymer‐dispersed liquid crystal fabrication under electric field

The transmission mode of holographic polymer‐dispersed liquid crystals (HPDLCs) was developed an under electric field. It is reported that orientation of LC molecules under an electric field induces orientation of oligomer molecules giving rise to low off‐state diffraction and small grating shrinkage. Copyright © 2005 Society of Chemical Industry     

A simple handling technique for mammalian oocytes and embryos during preparation for transmission electron microscopy

Due to their small size, mammalian oocytes and embryos pose unique problems during preparation for transmission electron microscopy. This paper outlines a method which combines protein embedding with centrifugation to locate the specimens on the face of a Beem capsule mould. This method facilitates both the processing of oocytes with minimal loss and rapid location of the specimens within the block for simultaneous sectioning, staining and examination.     

Using ion implantation to adjust the transition temperature of superconducting films

We summarize a continuing investigation into using ion implantation to alter the transition temperature of superconducting thin films. The primary motivation for the work presented here was to study the feasibility of using magnetic ion doping to replace the bi-layer T_c control process currently used for certain cryogenic detector applications at National Institute for Standards and Technology. The results from work with various ion species implanted into aluminum, molybdenum, titanium and tungsten host films are presented.     

Protein binding study of isoflavone, perillyl alcohol and S-ibuprofen by high-performance frontal analysis

High-performance frontal analysis (HPFA) was used for a protein binding study of isoflavones (daidzein, genistin, and genistein), enantiomers of perillyl alcohol and S-ibuprofen to human serum albumin (HSA). The analyses were performed on a Develosil and Inertsil 100-Diol-5 column (10 cm×4.6mm). Sodium phosphate solution (pH 7.4, ionic strength 0.17) was used as the mobile phase at a flow rate of 1 ml/min. To ensure the drug to be eluted as a trapezoidal peak with a plateau, injection volumes were each fixed up the zonal profile with an evident plateau appears. The unbound drug concentration was determined from a plateau height of the plateau region after that experimental data were fitted by Scatchard equation. The binding constants (K) and total binding affinities (nK) of drugs to HSA were calculated, respectively.     

A simple mathematical analysis on the effect of sand in Cr(VI) reduction using zero valent iron

A simple mathematical model was proposed to analyze the enhancement of Cr(VI) reduction when sand materials are added to the zero valent iron (ZVI). Natural decay of Cr(VI) in a control experiment was analyzed by using a zero-order decay reaction. Adsorption kinetics of Cr(VI) to sand was modeled as a first-order reversible process, and the reduction rate by ZVI was treated as a first-order reaction. Natural decay of Cr(VI) was also included in other experiments, i.e., the adsorption to sand, the reduction by ZVI, and both adsorption and reduction when sand and ZVI are present together. The model parameters were estimated by fitting the solution of each model to the corresponding experimental data. To observe the effect of sand addition to ZVI, both adsorption and reduction rate models were considered simultaneously including the natural decay. The solution of the combined model was fitted to the experimental data to determine the first-order adsorption and reduction rate constants when sand as well as ZVI is present. The first-order reduction rate constant in the presence of sand was about 35 times higher than that with ZVI only.