A wafer level monitoring method for plasma-charging damage usingantenna PMOSFET test structure

A novel monitoring method for plasma-charging damage is proposed. This method performs a quick and accurate evaluation using antenna PMOSFET. It was found that not only hot-carrier (HC) lifetime but transistor parameters such as initial gate current and substrate current were changed according to the degree of plasma-charging damage. However, the present work suggests that monitoring the shift of drain current after a few seconds of HC stress is a more accurate method to indicate plasma-charging damage. The monitoring method using the present test structure is demonstrated to be useful for realizing highly reliable devices     

Stabilization of inter-area and/or oscillatory modes in large-scale power system by voltage impedance power system (VIPS) apparatus based on decentralized control scheme

New technologies such as power electronics have made it possible to change continuously the impedance of a power system not only to control power flow but also to enhance stability. A power system incorporating a variable impedance apparatus such as a variable series capacitor (VSrC) and high-speed phase shifter (HSPS) is called VIPS (Variable Impedance Power System) by the authors. This paper proposes a novel control method of VIPS apparatus such as VSrC and HSPS installed at an interconnecting point for stabilizing inter-area unstable and/or oscillatory modes. The proposed design method of the control system is a kind of hierarchical decentralized control method of a large-scale power system based on a Lyapunov function. Under the proposed control scheme, each subsystem can be stabilized independently by local controllers such as AVR, speed governor and PSS, and then the whole interconnected system can be stabilized by VIPS apparatus taking into account interactions between subsystems. The effectiveness and robustness of the VIPS apparatus control are shown by numerical examples with model systems including a large-scale power system.     

Functioning survival rate of fixtures and superstructures of osseointegrated implants: ten years of progress in Tokyo Dental College Hospital (second report)

Endoglucanase production was measured in culture filtrates of four species of Saccobolus growing in media containing glucose or crystalline cellulose as the only carbon sources. Enzyme activity was four to seven times higher in the presence of cellulose than glucose. S. saccoboloides showed maximal growth and enzyme production. The extracellular proteins secreted during growth on cellulose were separated by polyacrylamide gel electrophoresis and stained for proteins. A zymogram technique was used to visualize bands with endoglucanase activity. The four species showed different protein and isoenzyme patterns.     

Micro-computerized tomographic observation of the spinning apparatus in Bombyx mori silkworms

Silkworms and spiders have evolved complex spinning apparatus thought to use highly controlled conditions to optimize protein folding and crystallization to provide a tough fiber. Accordingly, the structure and function of the natural spinning apparatus has been studied with great attention as an interesting piece of biological engineering with potential for mimicry in an industrial process. However it is still not well understood. Here we used Micro-Computerized Tomographic equipment (mCT) to visualize the three-dimensional structure of the spinning apparatus in Bombyx mori silkworms. Multidirectional tomograms obtained by X-ray radioscopy provided valuable information on the detailed arrangement of each muscle of the silk press. It is suggested that the duct in the silk press part plays a part as an extrusion die whose cross-sectional area can be controlled by muscles to optimize applied stresses in the partially gelled silk within its lumen.     

Accelerator Analysis of Tributyltin Adsorbed onto the Surface of a Tributyltin Resistant Marine Pseudoalteromonas sp. Cell

Tributyltin (TBT) released into seawater from ship hulls is a stable marine pollutant and obviously remains in marine environments. We isolated a TBT resistant marine Pseudoalteromonas sp. TBT1 from sediment of a ship’s ballast water. The isolate (10^{9.3 ± 0.2} colony-forming units mL⁻¹) adsorbed TBT in proportion to the concentrations of TBTCl externally added up to 3 mM, where the number of TBT adsorbed by a single cell was estimated to be 10^8.2. The value was reduced to about one-fifth when the lysozyme-treated cells were used. The surface of ethanol treated cells became rough, but the capacity of TBT adsorption was the same as that for native cells. These results indicate that the function of the cell surface, rather than that structure, plays an important role to the adsorption of TBT. The adsorption state of TBT seems to be multi-layer when the number of more than 10^6.8 TBT molecules is adsorbed by a single cell.     

Synthesis of tetramethyl-p-silphenylenesiloxanedimethylsiloxane triblock copolymer by employing living anionic polymerization

Dimethylsiloxane-tetramethyl-p-silphenylenesiloxane-dimethylsiloxane (DMS-TMPS-DMS) triblock copolymer was synthesized by employing living anionic polymerization of hexamethylcyclotrisiloxane (D₃). Two synthetic methods were carried out for the polymerization. One of those methods was the anionic polymerization of D₃ initiated at the silanolate anion which was prepared from the terminal hydroxyl group of silanol-terminated TMPS prepolymer by reaction with n-butyllithium (method 1). The other was the coupling reaction of vinyl-terminated TMPS prepolymer with hydrosilyl-terminated DMS prepolymer obtained from the anionic polymerization of D₃ by using diphenylmethylsilanolate anion as initiator (method 2). In method 1, DMS contents of the copolymers ranged from 25.8 to 72.5 wt% and the values agreed with the ratio of D₃ to TMPS prepolymer. The weight-average molecular weights ranged from 1.36×10⁴ to 19.4×10⁴ and were close to the predicted values calculated from the $\text{M}\text{?}{}_{\mathrm{v}}$ of the TMPS prepolymer and the amount of D₃ added. In the case of method 2, weight-average molecular weights ranged from 19.5×10⁴ to 24.2×10⁴. The high molecular weight copolymer could thus be obtained by method 2. Intrinsic viscosity values of the triblock copolymers agreed with calculated values obtained by considering the copolymer as a binary mixture of these homopolymers. Differential scanning calorimetry and thermogravimetry were carried out on the triblock copolymers. The equilibrium melting temperatures of each of the copolymers were very close to that of poly-TMPS (160°C). The glass transition temperature and heat of fusion were decreased as the DMS content was increased. The thermogravimetric curves for the copolymers indicated that the thermal stability of the triblock copolymer was intermediate between the DMS and TMPS homopolymers.     

Polymerization of methyl methacrylate by tri-n-butylborane in the presence of amino acid esters

The polymerization of methyl methacrylate by tri-n-butylborane in the presence of amino acid esters was investigated. The binary systems of tri-n-butylborane and amino esters were found to be more effective for initiating the polymerization than tri-n-butylborane alone. Co-catalytic effects of amino acid esters were in the order: tyrosinate > glutamate > aspartate ? phenyl alaninate > serinate > glycinate. The rate of polymerization in a mixture of dimethylsulphoxide and toluene was proportional to the square root of the concentration of the initiator system, to the monomer concentration, and to the concentration of dimethylsulphoxide in the solvent. The overall energy of activation was estimated to be 4.6 kcal/mol for the tri-n-butylborane/methyl tyrosinate system. Copolymerization curves gave a typical free-radical character.     

A low wall-loading DEMO reactor design with high priority for early and reliable realization of a tokamak fusion reactor over the cost performance

Based on scientific databases adopted for designing ITER plasmas and on the advancement of fusion nuclear technology from the recent R&D program, a low wall-loading DEMO fusion reactor has been designed, where high priority has been given to the early and reliable realization of a tokamak fusion plasma over the cost performance. Since the major radius of this DEMO reactor is chosen to be 10 m, plasma ignition is achievable with a low fusion power of 0.8 GW and an operation period of 4–5 hours is available only with inductive current drive. The low ignition power makes it possible to adopt a first wall with an austenitic stainless steel, for which significant databases and operating experience exists, due to its use in the presence of neutron irradiation in fission reactors. In step with development of advanced materials, a step-wise increase of the fusion power seems to be feasible and realistic, because this DEMO reactor has the potential to produce a fusion power of 5 GW.