Improvement of levitation characteristics in a magnetic bearing system using HTSC‐permanent magnet hybrid structure

Magnetic bearing using pinning force of a permanent magnet and a high‐temperature superconductor has been developed. Additional permanent magnet is introduced to increase the levitation force of the magnetic bearing. In this hybrid magnetic bearing system, levitation force is mainly given by the repulsive force of the permanent magnets, and stability for the lateral direction is given by pinning force of the superconductor. The experimental device is developed. A ring‐type superconductor and a bulk one are examined. Levitation characteristics of the hybrid magnetic bearing are measured. The bulk superconductor shows better characteristics of both levitation and lateral stability than the ring one. Levitation force of the hybrid system becomes about twice as large as that of the nonhybrid one. Although, the repulsive force of the permanent magnet decreases the lateral stability of the system, its influence becomes small by choosing an adequate position of the permanent magnets and the superconductor. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 71–77, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10350     

Sensors for the food industry

This article presents an overview of the results of a five-year research project on sensors for the food industry in Japan. This project was a government-sponsered research programme involving the food industry and the instrumentation industry, coordinated by the Japanese Ministry of Agriculture, Forestry and Fisheries. The programme focussed on 17 food processing operations and quality control tasks, where the need for an on-line (or rapid at-line) measurement had been established. The instrument development work employed biosensors pH and gas sensors, optical-imaging devices, as well as near-infrared, microwave, ultrasound and mechanical resonance techniques, together with robotics and advanced data-processing techniques.     

Oxidation of methane to formaldehyde over Fe/SiO2 and Sn---W mixed oxides

In an attempt to develop new catalysts for the formation of formaldehyde from methane, the promotion effect of Fe on SiO₂ and that of Sn on WO₃ have been studied. The formation of formaldehyde on silica can be appreciably enhanced by the impregnation of Fe, as far as iron loadings are kept below 0.1 atom.% (Fe/Si × 100). In the case of Sn---W---Ox catalysts, both the addition of Sn to WO₃, and that of W on SnO₂ were effective to the selective formaldehyde formation. Absorption spectra (UV-Vis) and ESR measurements revealed that tetrahedrally coordinated Fe³⁺ in the silica network plays an important role in the formation of formaldehyde. A thin surface layer consisting of W and Sn oxides can account for the selective formaldehyde formation on the Sn---W---Ox catalysts.     

Spherical Aluminum Nitride Fillers for Heat-Conducting Plastic Packages

It is necessary for encapsulants to have not only a suitable coefficient of thermal expansion (CTE) compatible to IC devices and a low dielectric constant to reduce the device propagation delay, but also a high thermal conductivity to dissipate large amounts of heat from power-hungry, high-speed IC and high-density packages. Fillers such as silica have been mixed with polymers to improve their properties. Aluminum nitride (AlN) is considered as an alternative one, because it has a higher theoretical thermal conductivity of ∼320 W/mK¹, a compatible CTE with silicon chips and a low dielectric constant. Commercial AlN fillers are angular in shape, because they are prepared via grinding coarse AlN powders synthesized by direct nitridation of aluminum metal and classification. The angular AlN are not expected to have high fluidity when mixed with polymers and hence low packing density. Recently, we successfully obtained single-crystalline spherical AlN fillers. Furthermore, polymer composites filled with the spherical AlN showed excellent thermal conductivity (>8 W/mK) as encapsulants for dissipating the heat generated in electronic devices.     

A manufacturing XML schema definition and its application to a data management system on the shop floor

Digitization for sharing knowledge on the shop floor in the machinery industry has been given much attention recently. To help engineers use digitization practically and efficiently, this paper proposes a method based on manufacturing case data that has a direct relation to manufacturing operations. The data are represented in XML schema, as it can be easily applied to Web-based systems on the shop floor. The definitions were made for eight manufacturing methods including machining and welding. The derived definitions consist of four divisions of metadata, work-piece, process and evaluation. Three divisions except for the “process” division are common to the manufacturing methods. The average number of elements for a manufacturing method is about 200. The represented schema is also used to convey knowledge such as operation standards and manufacturing troubleshooting on the shop floor. Using the definitions, a data management system is developed. It is a Web-based Q&A system, in which the engineers specify the manufacturing case data mainly by selecting from the candidates. Then, the system fills in the blank portions and/or shows messages to help complete the case data. The proposed method is evaluated through practical scenarios of arc welding and machining.     

An approximation algorithm dependent on edge-coloring number for minimum maximal matching problem

We consider the minimum maximal matching problem, which is NP-hard (Yannakakis and Gavril (1980) [18]). Given an unweighted simple graph G=(V,E), the problem seeks to find a maximal matching of minimum cardinality. It was unknown whether there exists a non-trivial approximation algorithm whose approximation ratio is less than 2 for any simple graph. Recently, Z. Gotthilf et al. (2008) [5] presented a -approximation algorithm, where c is an arbitrary constant.In this paper, we present a -approximation algorithm based on an LP relaxation, where χ^′(G) is the edge-coloring number of G. Our algorithm is the first non-trivial approximation algorithm whose approximation ratio is independent of |V|. Moreover, it is known that the minimum maximal matching problem is equivalent to the edge dominating set problem. Therefore, the edge dominating set problem is also -approximable. From edge-coloring theory, the approximation ratio of our algorithm is , where Δ(G) represents the maximum degree of G. In our algorithm, an LP formulation for the edge dominating set problem is used. Fujito and Nagamochi (2002) [4] showed the integrality gap of the LP formulation for bipartite graphs is at least . Moreover, χ^′(G) is Δ(G) for bipartite graphs. Thus, as far as an approximation algorithm for the minimum maximal matching problem uses the LP formulation, we believe our result is the best possible.     

A systolic algorithm for Euclidean distance transform

The Euclidean distance transform is one of the fundamental operations in image processing. It has been widely used in computer vision, pattern recognition, morphological filtering, and robotics. This paper proposes a systolic algorithm that computes the Euclidean distance map of an N /spl times/ N binary image in 3N clocks on 2N/sup 2/ processing cells. The algorithm is designed so that the hardware resources are reduced; especially no multipliers are used and, thus, it facilitates VLSI implementation.     

Calculations from texture of earing in deep drawing for FCC metal sheets

The present study aims to calculate the height at each peripheral position of a cup drawn from polycrystalline sheet using texture data. In the analytical treatment the polycrystalline sheet is simplified to an aggregation of many single crystals with various orientations, and the texture is represented by a three-dimensional crystallite orientation distribution function. The ear is calculated crystallographically using the orientation distribution function as a volume fraction of a certain oriented crystal. In the experiment aluminium, Al-Mg alloy and copper sheets which are treated under various conditions of cold rolling and heat treatment are used. The average textures over the thicknesses of the sheets are measured by the Schulz reflection method. The calculated ears based on the measured textures are compared with the experimental ears for each material. The results show that all the principal features of the ears of drawn cups are predicted satisfactorily by the calculation.     

Two-Parameter Thermal Lattice BGK Model with a Controllable Prandtl Number

In this paper, two time relaxation parameters are introduce to a thermal lattice BGK, model to make its Prandtl number controllable. The dependency of the Prandtl number on the two parameters is derived. Numerical measurement of the transport coefficients is used to demonstrate the validity of the method. Furthermore, two examples of convective heat transfer are calculated, with one to show the effectiveness, and the other to show the breakdown of the two-parameter formulation under different conditions.     

Modular high temperature reactor (Modular HTR) contributing the global environment protection

Rapid increasing of the energy demand and the economic growth of the developing countries are threatening to lead to unstable supply of the fossil resources and the aggravation of the global environment. Modular High Temperature Reactor (Modular HTR) is one of the most effective solutions of such problem. The GT-MHR (Gas-Turbine Modular Helium Reactor) is a typical plant of the Modular HTR, which is a high efficiency nuclear power generating plant, combined the Modular HTR having passive safety characteristics with the direct cycle helium gas turbine. It has sufficient potential to contribute the global environment protection with keeping the growing speed of the developing countries.

Fuji Electric joined the international GT-MHR project in January 1997 and has helped to finance it. Fuji Electric, in the behalf of the other participants of this project, introduces the outline of this project and main system of the GT-MHR plant in this paper.