Isolation of antimicrobial agent from the marine algae Cystoseira hakodatensis

Cystoseira hakodatensis is an unutilised brown algae belonging to family Sargassaceae. A crude methanol extract from the algae showed inhibitory effects on the growths of Bacillus cereus and Bacillus licheniformis. To isolate the major antimicrobial agent, a sequential active‐guided isolation procedure was applied: liquid–liquid extraction, column chromatography and bio‐autography. A marked antimicrobial agent (active α) was isolated in hydrophobic fraction and was determined to phenolics without carbohydrates and proteins by phytochemical test. Regarding the antimicrobial potential, the isolated active α showed better inhibitory effects against B. cereus and B. licheniformis at 2 and 4 times of lower concentrations (62.5 and 31.3 μg mL^?1) in comparison with epigallocatechin gallate. These results showed that C. hakodatensis is a potential source of antimicrobial agent capable of preventing the growth of the two bacteria.     

Stabilization of inter-area and/or oscillatory modes in large-scale power system by voltage impedance power system (VIPS) apparatus based on decentralized control scheme

New technologies such as power electronics have made it possible to change continuously the impedance of a power system not only to control power flow but also to enhance stability. A power system incorporating a variable impedance apparatus such as a variable series capacitor (VSrC) and high-speed phase shifter (HSPS) is called VIPS (Variable Impedance Power System) by the authors. This paper proposes a novel control method of VIPS apparatus such as VSrC and HSPS installed at an interconnecting point for stabilizing inter-area unstable and/or oscillatory modes. The proposed design method of the control system is a kind of hierarchical decentralized control method of a large-scale power system based on a Lyapunov function. Under the proposed control scheme, each subsystem can be stabilized independently by local controllers such as AVR, speed governor and PSS, and then the whole interconnected system can be stabilized by VIPS apparatus taking into account interactions between subsystems. The effectiveness and robustness of the VIPS apparatus control are shown by numerical examples with model systems including a large-scale power system.     

Superconductivity in SrTa2S5

A strontium tantalum sulfide, SrTa₂S₅, has a hexagonal structure with lattice constants of a =3.32 and c=24.1 Å. With decreasing temperature the electrical resistivity decreases monotonically and exhibits an abrupt superconducting transition at 3.16 K (midpoint). The diamagnetic susceptibility is observed below T_c. The magnetic susceptibility is nearly independent of temperature above T_c and shows Pauli paramagnetism.     

Construction of the plasmid PMEX8-HAK1 and random site-directed mutagenesis of human cytosolic adenylate kinase

The pMEX8-hAK1 vector was devised from the pAK plasmid (Kim J. H. et al., 1989, Protein Engineering 5, 379-386), which could directly express human adenylate kinase proteins without recombination and its single strand DNA could be withdrawn with helper phage for random site-directed mutagenesis. The conserved key residues at Lys21, Lys27, and Thr39 were engineered to obtain mutants for kinetic analysis. Three mutants were obtained as K21P, K27R, and T39S, their specific activities were strikingly reduced compared to those of wild type adenylate kinase. This pMEX8-hAK1 will be a powerful tool for site-directed mutagenesis to detect the substrate-enzyme interaction for human adenylate kinase including various other enzymes.     

Development of 170 GHz/500 kW gyrotron

A development of 170GHz/500kW level gyrotron was carried out as R&D work of ITER. The oscillation mode is TE_31,8. In a short pulse experiment, the maximum power of 750kW was achieved at 85kV/40A. The efficiency was 22%. In the depressed collector operation, 500kW/36%/50ms was obtained. The maximum efficiency of 40% was obtained at P_RF=470kW whereas the power decrease by the electron trapping was observed. Pulse extension was done up to 10s at P_RF=170kW with the depressed collector operation. The power was limited by the temperature increase of the output window.     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.     

Design optimization of tall tubular lead/acid cells based on an analysis of the reaction distribution

In order to estimate the discharge performance of tall lead/acid cells (with tubular positives), changes in current and potential distributions with discharge progress were calculated with a computer on the basis of plate resistance and the current—potential—time relationship between small facing parts of positive and negative plates. The taller the cell, the larger the voltage drop along the plates. Thus, the discharge time became shorter despite a large amount of available active mass remaining in the bottom part of the plates.Various current-collector designs were evaluated, e.g., one with varying resistance at each height; a side conductor placed along the plates and connected to them at the top, centre and bottom, etc. Results revealed an optimum collector design with which the maximum discharge capacity could be obtained. Furthermore, it was shown that the side conductor markedly improved the discharge performance because the active mass near the connecting parts was appreciably used.     

Titanium nitride precipitation behavior in thin-slab cast high-strength low-alloy steels

To assess the potential for obtaining and utilizing titanium nitride (TiN) refinement via the increased postsolidification cooling rates associated with thin-slab casting, TiN particle size distributions were evaluated by transmission electron microscope (TEM) examination of carbon extraction replicas. Eight commercially produced thin-slab cast TiN steels, nominally 0.05 pct C, 1.2 pct Mn, and one conventionally cast steel were received. Thin slab samples were taken from three locations in the production process: quenched after casting before the tunnel furnace, quenched after tunnel furnace soaking, and the as-rolled and air-cooled final product. Effects of cooling rate were evident in the results and agree with previously documented behavior, where precipitate size decreases with increased cooling rate. Statistical differences in particle size between specimens from steels with different chemistries were shown. These variations result from differences in the driving force for precipitation, rates of coarsening, and differences in volume fraction due to changes in steel composition. The interaction of composition and processing, such as soaking in the tunnel furnace and rolling, was found to be important. For example, the hyperstoichiometric steel (excess Ti) exhibited fine TiN after casting and soaking, but dramatic coarsening after hot rolling. This behavior was attributed to deformation enhanced particle coarsening, or incomplete precipitation after soaking, followed by continued growth during subsequent processing.     

Reliability of nonhermetic bias-free LiNbO/sub 3/ modulators

Reliability for nonhermetic bias-free LiNbO/sub 3/ optical modulators is estimated from aging data in both dry and damp heat conditions. The two dominant failure modes for these devices are: 1) device performance degradation due to temperature-activated drift of the annealed proton-exchange waveguide; and 2) optical insertion loss increase due to humidity-induced deterioration of glued fiber joints. A total failure rate of 30 failures in time (FITs) is predicted for 20 years operation at 45/spl deg/C and moderate humidity conditions (40% RH). This estimate based on laboratory-test data is consistent with a field failure rate <5 FITs observed in fielded devices.