吸湿凉爽机织物的结构设计与性能

为研究织物组织结构与复合纱线线密度对织物凉爽性能的影响,将线密度为7.4和9.8 tex涤纶分别与线密度为7.8 tex锦纶反向加捻、并线后作为纬纱,以8.3 tex涤纶/竹浆纤维50/50混纺纱作经纱,设计平纹、二上一下斜纹和透孔组织织物.测试织物的瞬间接触凉感、热湿舒适性能及织物干、湿态升温曲线,并采用凉爽温度指数对织物的综合凉爽性能进行评价.研究结果表明:6种设计织物的瞬间接触凉感均高于标准,且平纹织物最好,纬纱粗细对瞬间接触凉感影响不显著;透孔织物透气性最好,且在人体出汗的状态下具有较好的导湿散热性能.平纹织物凉爽温度指数最高,最大凉爽温度为2.8℃,综合凉爽性能最好.     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

一种基于空间到达角的卫星电子侦察信号分选方法

在建立简化的卫星电子侦察空间模型的基础上，提出了一种利用空间到达角分选卫星电子侦察信号的新方法。通过仿真实验验证了这种方法的可行性。该方法可用于密集信号的预处理。     

基于扩展分形和CFAR特征融合的SAR图像目标识别

研究了多信息融合技术在SAR图像目标识别中的应用。将扩展分形特征(Extended Fractal)与双参数恒虚警特征(Double Parameter CFAR)形成的多信息进行融合处理。运用Dempster-Shafer证据理论，在决策层对SAR图像中的像素进行识别分类。实验结果表明通过融合对像素分类的准确性明显好于单特征的检测结果，减少了虚警概率，提高了系统的识别能力。     

HNO3和有机介质中U（Ⅳ）的稳定性研究

研究了ＨＮＯ＿３和ＴＢＰ－煤油介质中Ｕ（Ⅳ）的稳定性。测定了两种介质中Ｕ（Ⅳ）、ＨＮＯ＿３、ＴＢＰ浓度和气相中氧浓度对Ｕ（Ⅳ）氧化速率的影响。Ｕ（Ⅳ）的氧化速率都随温度提高而明显增加．其表观活化能分别为９１ｋＪ／ｍｏｌ（ＨＮＯ＿３介质）和４２ｋＪ／ｍｏｌ（ＴＢＰ－煤油介质）。对两种介质中Ｕ（Ⅳ）的氧化速率规律进行了比较。     

Functional Properties and Food Applications of Rapeseed Protein Concentrate

Rapeseed protein concentrate (RC), prepared with 2% hexameta-phosphate, was tested for its functionality and performance in some foods. The RC had good nitrogen solubility, fat absorption, emulsification, and whipping capacities but poor water absorption and gelling properties. It increased the emulsion stability, and protein but lowered the fat content of wieners. It also increased the cooking yield, reduced the shrinkage and tenderized meat patties. Results were similar to soybean isolate except for the poorer color and flavor. The cooking yield of RC supplemented wieners was less than the all-meat control and soybean-supplemented wieners. A 9% RC dispersion mixed with an equal volume of eggwhite produced a meringue of comparable stability and texture to that of eggwhite alone.     

化学镀非晶态Ni—B合金的研究

本文通过化学镀方法在铜和钢上沉积非晶态Ni-B合金。着重讨论了还原剂浓度、络合剂浓度对化学镀沉积速率的影响;分析了它的耐蚀原因和其显微硬度随退火温度的变化情况并就其应用和发展略作说明。     

液蜡分离单体烃工艺的研究

C12H26，C13H28，C14H30等正构烷烃是重要的化工原料，可通过液蜡精馏得到。文章对液蜡精馏的工艺设计进行探讨，对影响工艺的参数进行了比较，寻找出精馏工艺的较佳方案，并通过了生产实践的检验。     

同位素中子源活化瞬发分析装置

一、基本原理自六十年代中期以来,中子活化瞬发γ射线元素分析技术(PNAA)得到人们广泛重视。与通常的中子活化分析(NAA)技术相比,它分析的是样品中的主要成分,若用同位素中子源,还可进行实时在线连续测定及现场分析。PNAA技术是用热中子与待测元素发生中子俘获反应,处于激发态的产物核在瞬间     

JOINING MECHANISMS OF β''''-Al2O3 CERAMIC AND PYREX GLASS TO Al MATRIX COMPOSITE

The bonding of β'-Al2O3 and pyrex glass to Al matrix composites by anodic bonding process is achieved. The microstructure of the bonded interface and the joining mechanisms are analyzed with scanning electron microscope (SEM), energy dispersive X-ray fluorescence spectrometer (EDX). It is observed that the bonding region across the interface consists of the metal layer, oxide transitional layer and the ceramic layer, with the transitional layer composed of surface region and sub-surface region. The bonding process can mainly be categorized into anodic bonding process and solid state diffusing process. The pile-up of the ions and its drift in the interface area are the main reasons for anode oxidation and joining of the interface. The temperature, voltage and the drift ions in the ceramic or glass during the bonding process are the essential conditions to solid state diffusing and oxide bonding at the interface. The voltages, temperature, pressure as well as the surface state are the main factors that influence the anodic bonding.