a-Si alloy three-stacked solar cells with high stabilized-efficiency

a-Si alloy three-stacked solar cells have been studied to improve the stabilized efficiency of a-Si: H based solar cells. Based on the analysis by the individual characterization method of the component cells in stacked type cells, the a-Si :H middle cell was replaced with an a-SiGe :H cell. Furthermore, the optical confinement technology was improved to obtain a high-output current with thin i-layer thickness in the a-SiGe :H bottom cell. By this device design, the initial conversion efficiency was improved up to 12.4% and more than a 10% stabilized efficiency was obtained in a-SiC :H/a-SiGe :H/a-SiGe :H three-stacked cells. These cell characteristics were confirmed by measurements at the JQA Organization (the former JMI Institute).     

Compatibility of alkaline earth metal (Mg, Ca, Sr)-doped lanthanum chromites as separators in planar-type high-temperature solid oxide fuel cells

The mechanical, electrical and thermal properties of alkaline earth metal (Mg, Ca and Sr)-doped LaCrO₃ have been examined as separators in planar-type high-temperature solid oxide fuel cells. The maximum three-point bending strength at 1000°C in air was measured and found to be 186 MPa for LaCr_0.9Mg_0.1O₃, 36 MPa for La_0.9Ca_0.1CrO₃ and 77 MPa for La_0.9Sr_0.1CrO₃. The La_0.8Sr_0.2CrO₃ separator placed in both an oxidizing and a reducing environment at 1000°C showed almost the same electrical conductivities of the H₂ atmosphere, and the conductivity was independent of sample thickness in the range 0.5–3.0 mm. For all the doped LaCrO₃ perovskites, a difference between the thermal expansion behaviours of air and the H₂ atmosphere was observed. In particular, the thermal expansion slope for the first heating cycle under the H₂ atmosphere showed a marked change. The volume changes were due to the formation of oxygen defects in the perovskite structure. This revised version was published online in November 2006 with corrections to the Cover Date.     

Micromachined piezoelectric force sensors based on PZT thin films

A micromachined lead zirconate titanate (PZT) force sensor for scanning force microscope (SFM) is conceptualized by its piezoelectricity. The fabrication procedure is interpreted, and mechanical characteristics of the micromachined PZT force sensors with various lengths are studied in this paper. A compact SFM is constructed by using the piezoelectric PZT sensor. A very clear image is taken by this SFM. The current study of the micromachined PZT force sensor can be considered as a breakthrough of design of SFM as well as a good example of integrated piezoelectric microdevices     

Tunable laser for sensing atmospheric transmission in the infrared region of 11 ∼ 16 µm

We succeeded in observing the continuously tunable, pulsed InSb SFR (Spin-Flip Raman) laser emission in the infrared region of 11～16µm (11.4～16.3µm) from only one InSb device, merely by adjusting the pumping wavelength (11 lines from the infrared NH₃ laser) and the applied magnetic field (0～80 kGauss).     

A rapid dot-blot method for species identification of bloodstains

A very simple and rapid test for species identification is reported. Extracts of bloodstains were applied to a synthetic porous membrane and dried. The membrane was then quenched with glycine buffered saline containing BSA and Tween 20. A suspension of colloidal gold particles (GP) coated with rabbit antiserum to human IgG was poured onto, gently whirled and aspirated through the membrane. Spots from the human and monkey bloodstains became red, whereas those from other species of animals remained unstained. This test was completed within 3 to 4 min, and the antibody-coated GP reagent was prepared within 20 min using a very small quantity of antiserum. Cellulose acetate membranes of 0.45 microns or more in pore size were appropriate to this test.     

Hinokitiol induces differentiation of teratocarcinoma F9 cells

Hinokitiol, a constituent of the wood of Chamaecyparis taiwanensis, was found to induce differentiation of teratocarcinoma F9 cells. When examined by the agar-overlay method, in which expression of plasminogen activator as a differentiation marker protein was detected, this compound exhibited a dose- and time-dependent induction. Induction of differentiation by hinokitiol occurred irreversibly and required its addition for more than 12h. Among its structure-related compounds tested, tropolone and two colchicine-related compounds exerted potent activities comparable to that of hinokitiol. These findings indicate that free tropolone structure in the molecules plays an essential role in inducing differentiation of F9 cells. Hinokitiol showed a strong inhibitory effect of DNA synthesis in very early stages of culture, suggesting that this effect may be responsible for triggering differentiation of F9 cells.     

A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

Monte Carlo simulation of hydrogen absorption in palladium and palladium–silver alloys

A modified Monte Carlo (MC) simulation was performed to investigate the hydrogen absorption behavior in Pd and Pd–Ag alloys of the composition Pd_xAg_1−x (x=0.7–0.8) under H₂ pressure (0.1 MPa) at different temperatures. The present method employed can consider the dissociative adsorption of hydrogen molecule and the subsequent absorption of hydrogen atom by formalizing the relationship between the pressure of hydrogen molecule and hydrogen atom. The potential parameters were determined to reproduce the solution enthalpy of hydrogen in pure metals. The results are in good agreement with experimental findings as well as previous theoretical studies. We confirmed that our method is useful to simulate the absorption of hydrogen in metals and alloys.