Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

Voltage sag compensation with minimum energy injection by use of a micro‐SMES

This paper presents a method to compensate voltage sags with minimum energy injection for a series‐connected voltage restorer using a micro‐SMES. A circuit for extracting the fundamental symmetrical components from sag voltages and a minimum energy injection algorithm is described. Simulations of voltage sag compensation have been carried out using PSCAD/EMTDC for various faults. The simulation results confirm the validity of the proposed method and show the possibility of reducing the size of energy storage devices. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(3): 70–80, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10047     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

An analysis of shielding against DC magnetic fields generated by electric railways. Evaluation of effective permeability of fine structure

This paper describes an effective analysis of magnetic shielding based on homogenization. The analyses become time‐consuming if the problems include the magnetic substances having fine structure. The homogenization of the structure makes it possible to analyze effectively the magnetic fields. The authors introduce a method to estimate the effective permeability of the homogenized substance. This method can be applied to any periodic structure made of magnetic substance. The magnetic shielding effects by the structures against direct‐current (DC) fields generated by electric railways are analyzed by using the present method. As a result, it is found that the overhead way and the protective fence near the railway work as a magnetic shield, whose effects can be improved by appropriate arrangement of those constructions. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 160(4): 7–15, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20310     

Liquid viscosities and densities of HFC-134a+glycol mixtures

Liquid viscosity and density of six binary mixtures of HFC-134a with glycols [ethylene glycol, diethylene glycol, triethylene glycol, polyethylene glycol (400), and polypropylene glycol (2000)] have been measured in the temperature range from 273 to 333 K. The viscosity was measured by a rolling-ball viscometer calibrated with standard liquids of viscosities and densities (JS5, JS10, JS20, and JS50). The density was measured with a glass pycnometer. The uncertainties of the measurements were estimated to be less than 3.4 % for viscosity and 0.04 % for density, respectively. An equation is given to represent the obtained viscosity values as a function of weight fraction and temperature.     

Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

Resistive superconducting transition of κ-type BEDT-TTF organic superconductors in a magnetic field

The superconducting transition of the organic compoundsκ-(BEDT-TTF)₂ X is studied by resistive measurement in a magnetic field up to 10 T applied normal to the conducting plane. For the salts withX=Cu[N(CN)₂]Br andX=CuCN[N(CN)₂] the transition shows fanshaped broadening caused by superconductivity fluctuation. For theX=Cu(NCS)₂ salt the resistivity shows a peak in the transition region in a magnetic field below 4 T.This phenomenon is suppressed in defect-reduced samples for intralayer conduction. We discuss this peak in relation to the thermal fluctuation on the Josephson junction structures in this salt.     

Stabilization of bioethanol recovery with silicone rubber‐coated ethanol‐permselective silicalite membranes by controlling the pH of acidic feed solution

In order to produce highly concentrated bioethanol by pervaporation using an ethanol‐permselective silicalite membrane, techniques to suppress adsorption of succinic acid, which is a chief by‐product of ethanol fermentation and causes the deterioration in pervaporation performance, onto the silicalite crystals was investigated. The amount adsorbed increased as the pH of the aqueous succinic acid solution decreased. The pervaporation performance also decreased with decreasing pH when the ternary mixtures of ethanol/water/succinic acid were separated. Using silicalite membranes individually coated with two types of silicone rubber, pervaporation performance was significantly improved in the pH range of 5 to 7, when compared with that of non‐coated silicalite membranes in ternary mixtures of ethanol/water/succinic acid. Moreover, when using a silicalite membrane double‐coated with the two types of silicone rubber, pervaporation performance was stabilized at lower pH values. In the separation of bioethanol by pervaporation using the double‐coated silicalite membrane, removal of accumulated substances having an ultraviolet absorption maximum at approximately 260 nm from the fermentation broth proved to be vital for efficient pervaporation. Copyright © 2005 Society of Chemical Industry     

Optimal production-inventory policy for make-to-order versus make-to-stock based on the M/Er/1 queuing model

This paper analyzes a multi-product production / inventory system where demands for each item arrive according to a Poisson process and the production time for each product has an Erlang distribution. The paper proposes an optimality condition that specifies whether each product should be produced make-to-stock or make-to-order. In the event a product should be produced make-to-stock, an approach for computing the optimal base-stock level is proposed. Numerical examples are given for illustrative purpose.     

Saturated liquid viscosities and densities of environmentally acceptable hydrochlorofluorocarbons (HCFCs)

Measurements of saturated liquid viscosities and densities were performed on environmentally acceptable hydrochlorofluorocarbons (HCFCs), CH₃CCl₂F (HCFC-141b), CH₃CClF₂ (HCFC-142b; only for viscosity), CF₃CF₂CHCl₂ (HCFC-225ca), and CClF₂CF₂CHClF (HCFC-225cb), using a capillary viscometer and a glass pycnometer in the temperature range from 273 to 353 K. The uncertainty in the measurement of viscosity is estimated to be 5% based on the comparison of the present data with those in the literature for HCFC-141b. An equation is given to represent our saturated liquid viscosity data as a function of temperature.