基于残差决策的自动飞行控制系统远程实时故障诊断

针对自动飞行控制系统结构复杂、关联部件众多,发生故障时诊断时间长,从而影响飞机运行效率的问题,提出一种基于飞机通信寻址报告系统(ACARS)的远程实时故障诊断方案。首先,分析自动飞行控制系统的故障特点,设计搭建检测滤波器;然后,利用ACARS数据链实时发送的自动飞行控制系统的关键信息进行相关部件的残差计算,并根据残差决策算法进行故障诊断及定位;最后,针对不同故障部件残差间的差异大、决策门限无法统一的缺点,提出基于二次差值的残差决策改进算法,减缓了检测对象的整体变化趋势,降低了随机噪声和干扰的影响,避免了将瞬态故障诊断为系统故障的情况。实验仿真结果表明,基于二次差值的改进残差决策算法避免了多决策门限的复杂性,在采样时间为0.1 s的情况下,故障检测所需时间大约为2 s,故障检测时间大幅降低,有效故障检测率大于90%。     

Cathode plasma electrolytic deposition of Al2O3 coatings doped with SiC particles

Semiconductor particles doped Al₂O₃ coatings were prepared by cathode plasma electrolytic deposition in Al(NO₃)₃ electrolyte dispersed with SiC micro- and nano-particles (average particle sizes of 0.5–1.7?µm and 40?nm respectively). The effects of the concentrations and particle sizes of the SiC on the microstructures and tribological performances of the composite coatings were studied. In comparison with the case of dispersing with SiC microparticles, the dispersion of SiC nanoparticles in the coatings was more uniform. When the concentration of SiC nanoparticles was 5?g/L, the surface roughness of the composite coating was reduced by 63%, compared with that of the unmodified coating. Friction results demonstrated that the addition of 5?g/L SiC nanoparticles reduced the friction coefficient from 0.60 to 0.38 and decreased the wear volume under dry friction. The current density and bath voltage were measured to analyze the effects of SiC particles on the deposition process. The results showed that the SiC particles could alter the electrical behavior of the coatings during the deposition process, weaken the bombardment of the plasma, and improve the structures of the coatings.     

Numerical Investigation of the Capture of Polydisperse Particles by Charged Droplets

The capture of particles by charged droplets was simulated by considering the electrostatic interactions of droplet-droplet and droplet-particle. The results indicate that the electrostatic repulsion between droplets leads to a dynamic accumulation mode of particles. However, the droplet spacing has an insignificant effect on the capture efficiency when the electrostatic deposition predominates. The increase of droplet charge remarkably improves the capture efficiency, in which the capture of fine particles accounts for the largest proportion. Compared to the droplet charge, the droplet size shows a limited improvement in the capture efficiency. Reducing the droplet velocity prolongs the capture time instead of enhancing the capture capacity per unit time, thereby improving capture efficiency.     

低渗低温低压水敏性储气层压裂改造技术研究与应用

低渗低温低压水敏性储气层因压裂液快速破胶困难、黏土膨胀水敏伤害严重和压后压裂液返排动力不足等因素，使得压裂增产面临诸多难题。针对上述难题进行了技术攻关，形成了弱交联、低温活化剂与超量破胶剂的低温储层快速破胶技术、有机盐与无机盐双元体系复合防膨技术以及高比例液氮全程助排的排液技术。该压裂增产改造技术使牛101井头屯河组首次获得工业油气流，扩展了三塘湖盆地勘探空间。     

玻璃碳电极的激光改性处理

玻璃碳电极（ＧＣＥ）用激光脉冲照射处理后，电化学反应行为发生很大变化。背景电流减小，Ｆｅ３＋／Ｆｅ２＋氧化还原电对的电极反应速率显著提高，抗坏血酸（ＡＡ）在电极上呈现明显的吸附作用。     

NK-EH500调质钢爆炸硬化的冲击动力学研究

通过试验并运用爆炸冲击动力学理论NK－EH500调质钢爆炸硬化进行了深入的研究，结果表明，金属材料存在硬化极限，调整炸药组成改变爆炸硬化可以满足不同金属材料的硬化要求，隔离式爆炸硬化有利于保护硬化工件外观的完整性，本研究对拓展爆炸硬化在实践中的应用领域具有重要的理论指导意义。     

捞油车自动排绳控制装置

针对部分油田采用捞油的采油方式，介绍的自动排绳装置，是双通道化例闭环控制系统，特点是按照输入的给定、误差信号方向、大小变化，输出信号的方向、大小随之变化，自动跟踪，自动补偿，输出速度连续无级变速，可以手动和自动工作。     

硫酸铈和磷酸处理对铌酸表面酸度及催化活性的影响

用硫酸铈和磷酸对固体铌酸进行了表面处理。表面酸度和TG DTA测定结果表明 ,与未处理的固体铌酸相比 ,处理后表面强酸量提高 3～ 5倍 ,耐受温度由 30 0℃提高到 5 0 0～ 6 0 0℃。用于催化酯化合成二甘醇二苯甲酸酯增塑剂 ,处理后固体铌酸的催化活性和重复使用寿命有明显提高。     

两缸天然气发动机工作均匀性分析

对一台火花点火式两缸天然气发动机进行了缸内示功图、进气压力波、空燃比、缸盖及活塞温度场和排放等项目的测试。试验和分析表明，两缸进气道中存在着明显的压力波动，波动程度取决于发动机工况。两缸混合气的质和量都不均匀，一缸空燃比偏浓，燃烧不完全，后燃倾向大；二缸空燃比较合适，燃烧过程较完善。两缸的尾气排放量相差不大。据此，可应用稀燃、快燃技术，以提高燃烧速度，改善燃烧过程；同时调整进气系统特性，将两缸混合气的质和量的不均匀性降到最低限度。