吸湿凉爽机织物的结构设计与性能

为研究织物组织结构与复合纱线线密度对织物凉爽性能的影响,将线密度为7.4和9.8 tex涤纶分别与线密度为7.8 tex锦纶反向加捻、并线后作为纬纱,以8.3 tex涤纶/竹浆纤维50/50混纺纱作经纱,设计平纹、二上一下斜纹和透孔组织织物.测试织物的瞬间接触凉感、热湿舒适性能及织物干、湿态升温曲线,并采用凉爽温度指数对织物的综合凉爽性能进行评价.研究结果表明:6种设计织物的瞬间接触凉感均高于标准,且平纹织物最好,纬纱粗细对瞬间接触凉感影响不显著;透孔织物透气性最好,且在人体出汗的状态下具有较好的导湿散热性能.平纹织物凉爽温度指数最高,最大凉爽温度为2.8℃,综合凉爽性能最好.     

Synthesis of amphiphilic magnetic microspheres by dispersion copolymerization of styrene and poly(ethylene oxide) macromonomer

Amphiphilic magnetic microspheres ranging in diameter from 5 to 100 µm were prepared by dispersion copolymerization of styrene and poly(ethylene oxide) vinylbenzyl (PEO‐VB) macromonomer (MPEO) in the presence of Fe₃O₄ magnetic fluid. The effects of various polymerization parameters on the average particle size were systematically investigated. The average particle size was found to increase with increasing styrene concentration and initiator concentration. It also increased with decreasing stabilizer concentration and molecular weight of MPEO. The content of the hydroxyl groups localized in the microspheres ranged from 0.01 to 0.2 mmol g^?1. © 2003 Society of Chemical Industry     

基于MATLAB的VSP测井仪推靠机构的优化设计

为使VSP井下油气层测井仪在工作中保持稳定,保证测试结果的准确性,根据VSP测井仪的实际结构建立了机构简图,并建立了与该机构相对应的数学模型,利用MATLAB软件编制程序,得出了合理的水平推力和间距长度,提高了推靠机构的稳定性及VSP测井仪的测试精度.     

憎水性栀子蓝色素制备的研究

以浓盐酸为催化剂,采用乙酸酐酯化处理水溶性栀子蓝色素,制备了憎水性栀子蓝色素.探讨了栀子蓝色素与乙酸酐料液比、反应时间和反应温度等因素对憎水性栀子蓝色素色价的影响.结果表明:采用料液比1:20,在常温下反应4 h,为制备憎水性栀子蓝色素的最优条件.同时,通过红外光谱、可见吸收光谱及溶解性对栀子蓝色素的酯化改性进行了初步的探讨.     

One-to-Many and Many-to-One Optical Chaos Communications Using Semiconductor Lasers

A theoretical construction of one-to-many (OTM) and many-to-one (MTO) chaos synchronization communications using semiconductor lasers is presented. One center laser provides strong injections (strong link) to other side lasers, and the side lasers also provide weak injections (weak link) to the center one. Simulation results show that the side lasers synchronize with the center laser through injection-locking. In addition, messages transmitted via the strong links or the weak links experience strong chaos pass filtering, enabling us to realize OTM and MTO communications.     

Investigation of Mechanical and Electrical Characteristics for Cracked Conductive Particle in Anisotropic Conductive Adhesive (ACA) Assembly

In an anisotropic conductive adhesive (ACA) assembly, the electrical conduction is usually achieved with the conductive particles between the bumps of integrated circuit (IC) and corresponding conductive tracks on the glass substrate. Fully understanding of the mechanical and electrical characteristics of ACA particles can help to optimize the assembly process and improve the reliability of ACA interconnection. Most conductive particles used in the ACA assembly are with cracks in the metal coating of the particles after the ACA bonding. This paper introduced the fracture analysis by applying the cohesive elements in the numerical model of the nickel-coated polymer particle and further simulating the cracks initiation and propagation in the nickel coating during the ACA bonding. The simulation results showed that the stress distribution on the nickel-coated particle with cracks was significantly different from that on the nickel-coated particle without crack, indicating that the stress analysis by taking the crack into consideration is very important for the reliability assessment of the ACA interconnection. The stress analysis of cohesive elements indicated that the cracks initiated at the central area of the nickel coating and propagated to the polar area. Furthermore, by the introduction of a new parameter of the virtual resistance, a mathematical model was established to describe the electrical characteristics of the nickel-coated particle with cracks. The particle resistance of the nickel-coated particle with cracks was found to be much higher than that of the particle without crack in the optimized bonding pressure range, indicating that it is necessary to take the crack into consideration for the particle conduction analysis as well. Therefore, the fracture analysis on the conductive particle by taking the crack into consideration could accurately evaluate the reliability of ACA interconnection and avoid serious reliability issues.     

Φ4.0m×60m回转窑辐射热的应用

水泥厂回转窑简体内砌筑了耐火砖隔热,但仍有部分热通过简体以辐射的形式散失到大气中,吸收利用这部分辐射热也是一项节能减排的举措.     

求非线性方程近似解的逐次迭代法

本文提出了求解非线性问题的一种新方法——逐次迭代法，本方法先是给出一个初始近似解，然后将这个近似解进行校正迭代，使之接近于真实解，把一个非线性问题转化为一个线性问题来解决。     

无线电引信多普勒信号增速器的研究

论述了无线电引信多普勒信号增速器的实现原理及意义，介绍了采用ＴＭＳ３２０Ｃ３０作为ＣＰＵ、多片大容量静态ＲＡＭ芯片构成海量存储体的信号增速器硬件结构和软件设计，并提出了今后的研究方向。