A new Pd-oxide-Al/sub 0.3/Ga/sub 0.7/As MOS hydrogen sensor

A new and interesting Pd-oxide-Al/sub 0.3/Ga/sub 0.7/As MOS hydrogen sensor has been fabricated and studied. The steady-state and transient responses with different hydrogen concentrations has been measured at various temperatures. Based on the large Schottky barrier height and presence of oxide layer, the studied device exhibits a high hydrogen detection sensitivity and wide temperature operating regime. The studied device exhibits the low-leakage current and obvious current changes when exposed to hydrogen-contained gas. Even at room temperature, a very high hydrogen detection sensitivity of 155.9 is obtained when a 9090 ppm H/sub 2//air gas is introduced. Furthermore, when exposed to hydrogen-contained gas at 95/spl deg/C, both the forward and reverse currents are substantially increased with increased hydrogen concentration. In other words, the studied device can be used as a hydrogen sensor under the applied bidirectional bias. Under the applied voltage of 0.35 V and 9090 ppm H/sub 2//air hydrogen ambient, a fast adsorption response time about 10 s is found. The transient and steady-state characteristics of hydrogen adsorption are also investigated.     

合成己二腈反应技术研究——(Ⅴ)己二腈工业反应过程模拟与反应器改造

对己二腈工业反应器提出了两釜串联带回流的模型,通过模拟计算得出模型的级间返混系数 f=6的结论。该模型能较好地预测工业反应器中物料组分浓度变化和气、液两相的流动特性;指出了现工业反应器的鼓泡中和段体积偏小是造成己二酸浓度偏高的关键;提出了可以通过增加串连一个鼓泡预反应段的改造方案,能有效地降低己二酸的浓度,从7%降至4%左右,从而能较好地减缓腐蚀和结焦。     

新型实用布线算法──L─M算法

本文提出新型布线算法，集李氏迷宫法与线搜索法的长处为一体，以饱和带法进行动态排序，以线搜索法确定借孔位置，然后用李氏法进行单层布线，获得最佳路径，从而达到线型好，布通率高的效果。     

Residual stresses and transformation toughening in MoSi2 composites reinforced with partially stabilized zirconia

The results of study of the effects of yttria stabilization (0–6 mol.%) on the room-temperature fracture behavior and toughening mechanisms in zirconia-reinforced MoSi₂ are presented in this paper. Transformation toughening is shown to occur only in composites reinforced with zirconia particles stabilized with 2 mol.% yttria. However, the fracture toughness levels are comparable in the other composites with yttria levels between 0 and 6 mol.%. Toughening in the other composites is attributed to the combined effects of residual stress, microcrack shielding/anti-shielding and/or crack deflection. A rigorous micromechanics-based model is presented for the estimation of residual stress levels in brittle materials reinforced with phases that can transform during cooling or under stress. The model is applied successfully to the rationalization of the observed fracture and toughening phenomena.     

Depth of intergranular oxygen diffusion during environment-dependent fatigue crack growth in alloy 718

The elevated-temperture fatigue crack growth behavior in alloy 718, when subjected to a loading frequency lower than the transitional frequency of this alloy, is viewed as fully environment dependent. In this process, the crack growth increment per loading cycle is assumed to be equal to the intergranular oxygen diffusion depth at the crack tip during the cycle effective oxidation time. In order to identify the trend of this diffusion depth an experimental program was carried out on compact tension specimens made of alloy 718 at 650 °C in which fatigue crack growth measurements were made for cyclic load conditions with and without hold time periods at minimum load level. This work resulted in establishing a relationship correlating the intergranular oxygen diffusion depth and the value of the stress intensity factor range ΔK. This relationship, when integrated over the cycle effective oxidation time, results in a closed-form solution describing the environment-dependent fatigue crack growth rate. A comparison is made between the results of this solution when applied to different loading frequencies and the corresponding experimental results. This comparison shows good agreement between the two sets of results. Furthermore, by combining the parabolic rate law of diffusion and the equation for the intergranular oxygen diffusion depth, an explicit expression for the oxygen diffusivity of grain boundaries is derived. It is found that this diffusivity is both a ΔK- and a frequency-dependent parameter.     

Modeling Power Supply Noise in Delay Testing

Excessive power supply noise during test can cause overkill. This article discusses two models for supply noise in delay testing and their application to test compaction. The proposed noise models avoid complicated power network analysis, making them much faster than existing power noise analysis tools. can cause performance degradation and     

Hydrogenated amorphous silicon thin-film transistor arrays fabricated by digital lithography

A jet-printed digital-lithographic method, in place of conventional photolithography, was used to fabricate 64 /spl times/ 64 pixel (300 /spl mu/m pitch) matrix addressing thin-film transistor (TFT) arrays. The average hydrogenated amorphous silicon TFT device within an array had a threshold voltage of /spl sim/3.5 V, carrier mobility of 0.7 cm/sup 2//V/spl middot/s, subthreshold slope of 0.76 V/decade, and an on/off ratio of 10/sup 8/.     

Acoustical tomography based on the second-order Born transformperturbation approximation

Reconstruction algorithms and their numerical examples of acoustical tomography based on the second-order Born transform perturbation approximation are presented. The reconstruction algorithms in the second-order Born approximation are similar in form to those in the first-order Born approximation. Replacing the angular spectrum of the scattered wave in the first-order case by the result of applying a first-order operator to the angular spectrum of the scattered wave or applying a second-order operator to the angular spectrum of the incident wave leads to the second-order reconstruction algorithms. Also, comparisons of reconstruction algorithms of the first- and second-order Born approximations are given, and they show that the second-order Born approximation algorithms have a distinct advantage over the first-order approximations in many cases