Applications and Technologies of All-Solid State Blue Laser

1 Introduction Along with the matureness of laser diode (LD) manufacturing technology, the performance of LD has been improved greatly since 1980s, so various kinds of laser devices based on LD have been developed rapidly, especially the all-solid state lasers. After early experiments and researches, the all-solid state lasers have been commercialized successfully.     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

在役超高压水晶釜主要检测方法

介绍了在役超高压水晶釜的常见缺陷以及应用超声波探伤、磁粉探伤、金相分析等无损检测方法对其进行在役检验的要点.     

Robust Distributed Source Coding

We consider a distributed source coding system in which several observations must be encoded separately and communicated to the decoder by using limited transmission rate. We introduce a robust distributed coding scheme which flexibly trades off between system robustness and compression efficiency. The optimality of this coding scheme is proved for various special cases.     

2007年国外有机硅进展

根据2007年公开发表的相关资料,综述了2007年国外有机硅行业的市场动向、行业动向及有机硅产品的研发进展.     

高柔韧性尼龙1010材料的制备

对尼龙1010/NBR/增塑剂体系进行了系统研究,发现在挤出机中环氧扩链剂可以对尼龙进行扩链反应,且环氧树脂对尼龙1010的扩链反应活性较高,扩链效果比较明显;N-丁基苯磺酰胺是尼龙的良好增塑剂,经增塑、增韧后可以使经扩链后的尼龙1010柔韧性有明显提高.采用SEM和TEM对所制备的材料进行了形貌分析,发现用NBR增韧尼龙,对于不同的基体材料,橡胶粒子的形貌有很大不同,粒子由增韧纯尼龙的椭球形变为在增塑尼龙基体中不规则的形状.     

交流，共享，流动——现代大空间办公模式的优劣与对策

讨论了现代办公空间设计出现的新要求,通过办公空间演变趋势的探讨,归纳为若干大空间办公模式,并分析、比较其空间性质及特点,以及采用开放式办公布局的优势、不足及解决对策.