吸湿凉爽机织物的结构设计与性能

为研究织物组织结构与复合纱线线密度对织物凉爽性能的影响,将线密度为7.4和9.8 tex涤纶分别与线密度为7.8 tex锦纶反向加捻、并线后作为纬纱,以8.3 tex涤纶/竹浆纤维50/50混纺纱作经纱,设计平纹、二上一下斜纹和透孔组织织物.测试织物的瞬间接触凉感、热湿舒适性能及织物干、湿态升温曲线,并采用凉爽温度指数对织物的综合凉爽性能进行评价.研究结果表明:6种设计织物的瞬间接触凉感均高于标准,且平纹织物最好,纬纱粗细对瞬间接触凉感影响不显著;透孔织物透气性最好,且在人体出汗的状态下具有较好的导湿散热性能.平纹织物凉爽温度指数最高,最大凉爽温度为2.8℃,综合凉爽性能最好.     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

一种基于空间到达角的卫星电子侦察信号分选方法

在建立简化的卫星电子侦察空间模型的基础上，提出了一种利用空间到达角分选卫星电子侦察信号的新方法。通过仿真实验验证了这种方法的可行性。该方法可用于密集信号的预处理。     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

基于扩展分形和CFAR特征融合的SAR图像目标识别

研究了多信息融合技术在SAR图像目标识别中的应用。将扩展分形特征(Extended Fractal)与双参数恒虚警特征(Double Parameter CFAR)形成的多信息进行融合处理。运用Dempster-Shafer证据理论，在决策层对SAR图像中的像素进行识别分类。实验结果表明通过融合对像素分类的准确性明显好于单特征的检测结果，减少了虚警概率，提高了系统的识别能力。     

HNO3和有机介质中U（Ⅳ）的稳定性研究

研究了ＨＮＯ＿３和ＴＢＰ－煤油介质中Ｕ（Ⅳ）的稳定性。测定了两种介质中Ｕ（Ⅳ）、ＨＮＯ＿３、ＴＢＰ浓度和气相中氧浓度对Ｕ（Ⅳ）氧化速率的影响。Ｕ（Ⅳ）的氧化速率都随温度提高而明显增加．其表观活化能分别为９１ｋＪ／ｍｏｌ（ＨＮＯ＿３介质）和４２ｋＪ／ｍｏｌ（ＴＢＰ－煤油介质）。对两种介质中Ｕ（Ⅳ）的氧化速率规律进行了比较。     

存在噪声和未建模动态系统传递函数的渐近无偏估计

存在未建模动态时，如何去除系统传递函数估计中噪声引起的偏差是系统辨识关心的重要问题。本文将我们已提出的ＢＥＬＳ方法进行推广得出：当系统未建模动态可用－ＦＩＲ模型描述时，应用本文的方法可得到系统传递函数的无偏辨识，而不需知道有关噪声和未建模动态概率分布函数的先验知识。     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

液蜡分离单体烃工艺的研究

C12H26，C13H28，C14H30等正构烷烃是重要的化工原料，可通过液蜡精馏得到。文章对液蜡精馏的工艺设计进行探讨，对影响工艺的参数进行了比较，寻找出精馏工艺的较佳方案，并通过了生产实践的检验。     

气缸可靠性试验装置的研制

为了进行气缸可靠性试验研究,针对缸径为50mm、行程为160mm的气缸研制了一套气缸可靠性试验装置.5个月的不间断试验测试及获得的大量数据表明,该装置运行稳定可靠,满足了气缸可靠性试验的要求.详细介绍了装置试验回路的构成、工作原理和具体实现,测控子系统的硬件构成和软件流程,气缸性能参数测量方法及获得的部分数据.