用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

一种新型回路电阻测试仪的研究与设计

针对传统低压回路电阻测试仪只能在被测设备停电时使用的一大限制,本文提出并设计了一种新型低压回路电阻测试仪。该仪器可在低压设备运行状态下对其回路电阻进行测量,在保证测量精度的前提下减少了设备停电率,大大提高了工作效率。     

Integrated circuit and system design for renewable energy inverters

This study proposes that a novel integrated circuit (IC) and system design for renewable energy inverters can harvest renewable energy to power direct current (DC) and alternating current (AC) loads. In addition, an intelligent synthesis and management tool is developed to design the proposed system and to judge the system’s operational maintenance decisions. Finally, a renewable energy inverter’s information is posted to an online system. Users can obtain the proposed system’s information at any time and place. The accurate and superior performance of the proposed IC and system is confirmed by computer simulations and experimental results.     

面向航空通信应用的边沿触发器教学设计

研究和分析了面向航空通信应用的边沿触发器教学设计。以边沿触发电路实现原理为核心,引导边沿触发机制的探究式学习；以航空机载网络通信为具体应用背景,引入科学研究和工程实现中实际问题,设计曼切斯特码检测系统实验；使得边沿触发器教学成为“知识再创造”的过程和创新实践的新载体,以期培养新工科背景下的独立、创新和实践精神。     

关于硬件木马电路检测技术分析及发展趋势探讨

本文结合HTH电路的复杂性等特征分析与实际应用现状,研究了HTH电路的具体检测技术方法并对当前热点技术进行对比分析,探讨了HTH电路检测方法的技术发展趋势。     

燃煤锅炉除尘专用滤料的开发

介绍机械制造厂燃煤锅炉的烟尘特点,分析滤料失效的原因,提出一套针对该工况的滤料解决方案。介绍针对复杂工况条件所选用的纤维种类以及复合面层原料成分配比的确定,最终选用针刺工艺加工并对该新产品的基本性能进行了测试分析。     

A practical Equivalent Electrical Circuit model for Proton Exchange Membrane Fuel Cell (PEMFC) systems

An alternative Equivalent Electrical Circuit for Proton Exchange Membrane Fuel Cells is modelled in this study. Both I–V characteristics and H₂ consumptions corresponding to generated power under load and no-load conditions are investigated. For this purpose, H₂ consumptions and I–V characteristics of three different sized PEMFCs are tested. There is a very good harmony between the model results and measured values (relative error %0.7, %6.4 and %2.5 for FC-A, FC-B and FC-C respectively). In the proposed model current passes only on parallel resistance and not on serial resistance at no-load condition. Thus, a FC with higher parallel resistance should be preferred. Another key output of this study is that based on the proposed model, performance comparison of FCs can be performed with the parameters defined in this work. Proposals made in this study can easily be used for performance analysis of FCs under for both steady state and transient analysis.     

Study of planar structure applying reciprocity technique combined with MGEC and analysis of discontinuity

The 3D structure electromagnetic computation presents several difficulties related to the volume mesh. In fact, the entire volume space must be taken into account even the smallest details. In this article, we propose a formulation based on the reciprocity theorem combined with the generalized equivalent circuit method to model a planar 3D structure with both coaxial and planar excitation. The major advantage of this formulation is the fact to reduce the computational volume into 2D ones in the discontinuity plane. In addition, we focused on the calculation of the discontinuity between the excitation source and the planar structure to determine the exact behavior of the electric coaxial excitation model. The obtained current density, electric field distributions, and the input impedance are presented and discussed in the following sections. An approximately good agreement of input impedance with those obtained by the simulator and measurement is shown.     

声波测井换能器激发响应实验研究

声波测井换能器的激发响应由换能器振动时所表现出来的动态阻抗和激发电路参数决定。而换能器的动态（阻抗）参数随压电晶体及其装配方式（力学边界条件）改变。为了测量换能器动态参数的影响，采用声波测井仪器常用的压电晶体和升压变压器，通过改变激发脉冲宽度和直流电压进行了实验，结果发现：在换能器两端的瞬态响应中，一共有三个二阶网络响应，分别对应于不同的频率。最低的一个影响声波测井波形的基线、与换能器主频接近的一个决定激发效率以及电路与压电晶体之间的匹配关系，是激发电路设计中比较关键的，其参数可以通过导纳圆测量仪器得到。     

一种智能型的PCB产业需求预测方法

目前需求预测在整个印制电路板产业的生产活动控制中正扮演着越来越重要的角色。分析了影响印制电路板需求的因素和现有的预测方法,提出了一种适用于PCB产业需求预测的有效方法——遗传/BP—神经网络。实验表明该方法能够进一步改善印制电路板预测的准确度和减少生产成本的消耗。