Microstructures and properties of nickel-titanium carbide composites fabricated by laser cladding

In this work, Ni/TiC composites were synthesized by the laser cladding technique (LCT). A scanning electron microscope (SEM), X-ray diffractometer (XRD), microhardness meter, electrochemical workstation, and friction and wear tester examined the microstructure, surface morphology, phase structure, microhardness, wear, and corrosion resistances of the Ni/TiC composites. These results indicated the Ni/40TiC composite contained finer equiaxed crystals than the Ni and Ni/20TiC composites. In addition, numerous TiC particles in the Ni/40TiC composite impeded growth of the nickel crystals, which resulted in the fine microstructure of the Ni/40TiC composite. The Ni, Ni/20TiC, and Ni/40TiC composites exhibited face-centered cubic (f c c) lattices. The average microhardness values of the Ni/20TiC and Ni/40TiC composites were approximately 748 HV and 851 HV, respectively. The Ni/40TiC composite had the lowest friction coefficient (0.43) among all three coatings, and only some shallow scratches appeared on the surface of the Ni/40TiC composite. The corrosion potential (E) of Ni/40TiC exceeded the Ni/20TiC composite, and both were larger than the Ni composite, which indicated the Ni/40TiC composite had outstanding corrosion resistance and the Ni composite had poor corrosion resistance. The corrosion current densities (i) of Ni, Ni/20TiC, and Ni/40TiC composites were 5.912, 4.405, and 3.248 μA/cm², respectively.     

用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

The production of Indo-Pacific monochrome drawn glass beads in the Sasanian Empire: Insights from Xinjiang,northwest China

Indo-Pacific glass beads are produced by the drawn technique, which originates from South Asia, and their chemical compositions are unique in South and Southeast Asia. However, a small number of Indo-Pacific beads with Sassanian glass compositions are excavated in Asia and Africa after the 3rd c. CE, and their production sites in South/Southeast Asia or in the Sassanian region remain controversial. In this study, 15 drawn glass beads with various colours from Astana necropolis (ca. the 4th-8th c. CE) in Xinjiang, northwest China were investigated by using laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS), Scanning Electron Microscope, Raman spectroscopy and visible to near-infrared spectroscopy to characterize the production technology and origins. The results show that most Astana glass beads share similar chemical compositions with the glassware from Veh Arda?īr, a famous Sasanian site. Furthermore, Sasanian glass compositions predominate in Indo-Pacific beads in Xinjiang during the 4th-8th c. CE, while popular glass recipes in contemporary South/Southeast Asia are infrequently found; thus, it is deduced that the drawn method should have been mastered by Sasanian craftsmen. Moreover, the cobalt materials in Sasanian glass were imported from further western regions and changed over time. The popular Sasanian glass across central Eurasia reflects the trade monopoly of Sasanian in West and Central Asia, and the land glass bead trade is distinct from the contemporary maritime trade in the Indian and Pacific Oceans.     

Determinants of the intention to use non-medical insertable digital devices: The case of Chile and Colombia

In the past, thinking of carrying electronic devices inside our bodies was only posed by non-real scenarios. The emergence of insertable devices has changed this. Since this technology is still in its initial development stages, few studies have investigated factors that influence its acceptance. This paper analyzes the predictors of the intention to use non-medical insertable devices in two Latin American contexts. We used partial least squares structural equation modeling to examine whether six constructs predicted intention to use insertable devices. A questionnaire was administered to undergraduate students located in Colombia and Chile (n = 672). We also examined whether these predictors influenced intention differently for both of them. Four common constructs significantly and positively influenced both Chilean and Colombian respondents to use insertable devices (hedonic motivation, habit, performance expectancy, and social influence). Also, the habit has a complementary mediating effect on the relationship between social influence and behavioral intention. By contrast, effort expectations were a positive and significant predictor, but only among Chilean respondents. Findings suggest that when technologies are emerging, well-known predictors of intention (e.g., performance and effort expectations) are less influential than predictors related to self-efficacy (e.g., habit and hedonic motivation). The use of insertable devices has a significant impact on society. Thus, a better understanding of what motivates their use has implications for both academia and industry.     

数字签名技术在医院电子病历中的设计与应用

为推进病历数字化发展,并确保其信息的安全性,将以HIS电子病历系统为基础,采用安信数字签名技术和PKI或PMI系统搭建相信并加以任用的授权服务,经过针对实际的PKC和CA的确认、委托与管控构建整体的数字签名平台,完成电子病历数字签名功能设计,以加强电子文件的完整性、真实性和不可抵赖性。最后以某医院的XML结构化的电子病历系统为基础进行项目实施,完成了医护人员通过HIS的快速身份认证,和准确地数字签名。     

2.3–21 GHz broadband and high linearity distributed low noise amplifier

This paper focuses on the design of a 2.3–21 GHz Distributed Low Noise Amplifier (LNA) with low noise figure (NF), high gain (S₂₁), and high linearity (IIP3) for broadband applications. This distributed amplifier (DA) includes S/C/X/Ku/K-band, which makes it very suitable for heterodyne receivers. The proposed DA uses a 0.18 μm GaAs pHEMT process (OMMIC ED02AH) in cascade architecture with lines adaptation and equalization of phase velocity techniques, to absorb their parasitic capacitances into the gate and drain transmission lines in order to achieve wide bandwidth and to enhance gain and linearity. The proposed broadband DA achieved an excellent gain in the flatness of 13.5 ± 0.2 dB, a low noise figure of 3.44 ± 1.12 dB, and a small group delay variation of ±19.721 ps over the range of 2.3–21 GHz. The input and output reflection coefficients S₁₁ and S₂₂ are less than −10 dB. The input compression point (P_1dB) and input third-order intercept point (IIP3) are −1.5 dBm and 11.5 dBm, respectively at 13 GHz. The dissipated power is 282 mW and the core layout size is 2.2 × 0.8 mm².     

Effect of apple cider vinegar agent on the microstructure,phase evolution,and magnetic properties of CoFe2O4 magnetic nanoparticles

In the present study, spinel structure CoFe₂O₄ nanoparticles were successfully synthesized by the sol-gel auto-combustion technique. The effect of apple cider vinegar (ACV) addition as an organic biocompatible agent on the size, morphology, and magnetic properties of CoFe₂O₄ nanoparticles was investigated in detail. The phase evolution, particle size, and lattice parameter changes of the synthesized phase have been estimated by using Rietveld structure refinement analysis of X-ray powder diffraction data. Also, Fourier transform infrared spectra (FT-IR) of the samples verified the presence of two expected bands correspond to tetrahedral and octahedral metal-oxygen complexes within the spinel structure. Furthermore, microstructural observations revealed that ultrafine particles have a semi-spherical morphology. It was shown that the particles size decreased from ~45 to ~17 nm with an increase in the amount of ACV. Magnetic properties were carried out by vibrating sample magnetometer (VSM) at room temperature. Both the saturation magnetization (M_s) and coercivity (H_c) were found to be significantly dependent on the crystallite size and the amount of ACV.     

Digital Microfluidics for Manipulation and Analysis of a Single Cell

The basic structural and functional unit of a living organism is a single cell. To understand the variability and to improve the biomedical requirement of a single cell, its analysis has become a key technique in biological and biomedical research. With a physical boundary of microchannels and microstructures, single cells are efficiently captured and analyzed, whereas electric forces sort and position single cells. Various microfluidic techniques have been exploited to manipulate single cells through hydrodynamic and electric forces. Digital microfluidics (DMF), the manipulation of individual droplets holding minute reagents and cells of interest by electric forces, has received more attention recently. Because of ease of fabrication, compactness and prospective automation, DMF has become a powerful approach for biological application. We review recent developments of various microfluidic chips for analysis of a single cell and for efficient genetic screening. In addition, perspectives to develop analysis of single cells based on DMF and emerging functionality with high throughput are discussed.     

A review on ultrasonic spot welding of copper alloys

As a solid state joining process, ultrasonic spot welding has been proven to be a promising technique for joining copper alloys. However, challenges still remain in employing ultrasonic spot welding to join copper alloys. This article comprehensively reviews the current state of ultrasonic spot welding of copper alloys with a number of critical issues including materials flow, plastic deformation, temperature distribution, vibration, relative motion, vertical displacement, interface friction coefficient, online monitoring technique, coupled with the macrostructure and microstructure, the mechanical properties and electrical conductivity. In addition, the future trends in this field are provided.     

Inverse identification of constitutive parameters from heat source fields: A local approach applied to hyperelasticity

In this paper, a new inverse identification method of constitutive parameters is developed from full kinematic and thermal field measurements. It consists in reconstructing the heat source field from two different approaches by using the heat diffusion equation. The first one requires the temperature field measurement and the value of the thermophysical parameters. The second one is based on the kinematic field measurement and the choice of a thermo-hyperelastic model that contains the parameters to be identified. The identification is carried out at the local scale, ie, at any point of the heat source field, without using the boundary conditions. In the present work, the method is applied to the challenging case of hyperelasticity from a heterogeneous test. Due to large deformations undergone by the rubber specimen tested, a motion compensation technique is developed to plot the kinematic and the thermal fields at the same points before reconstructing the heterogeneous heat source field. In the present case, the constitutive parameter of the Neo-Hookean model has been identified, and its distribution has been characterized with respect to the strain state at the surface of a cross-shaped specimen.