Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.     

欠平衡钻井过程中的井控新设备

文章简述了欠平衡钻井中不压井操作的设备和方法,介绍了威得福公司的井下套管阀和海底泥浆举升钻井工业联合项目在深水钻井中研发的新钻杆阀在欠平衡钻井中的应用。通过在钻杆上安装钻杆阀和在套管上安装套管阀解决接单根及起下钻操作时因压井可能破坏欠平衡状态的问题,使全过程的欠平衡钻井得以实现。     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

蓄热式均热炉生产中存在问题的分析及解决方案

介绍了高温空气燃烧技术在均热炉上的应用情况，对应用中出现的问题进行了分析，并提出了解决方案。     

液晶光阀光电导层光吸收系数的研究

用化学气相沉积法制备了液晶光阀中光电导层———非晶硅薄膜,从实验中得出最佳制备工艺的参数取值。给出了用包络线法测量非晶硅薄膜光吸收系数的原理,测量了样品的光吸收系数随波长的变化规律。得到样品在最佳工艺条件下的光吸收系数高于1×103cm-1。     

Investigation on vapor-cooled current leads operating in a pulse mode

This paper describes transient numerical modeling for thermal characteristic of vapor-cooled current leads under pulse operation. The transient thermal analysis considers the temperature difference between a helium gas flow and a copper lead with temperature dependent properties of helium gas, copper and stainless steel. The numerical analysis was validated by an experiment with commercially available 100 A vapor-cooled current leads. A proper overloading factor calculation and the effect of intermediate cooling are presented for the current leads under pulse operation, which can significantly reduce heat input to a cryostat.     

电接点压力表补水泵定压系统的应用

阐述了电接点压力表补水泵定压系统的一些应用问题 ,给出了电接点压力表定压点的上、下限计算公式 ,并提出了该系统补给水泵、补给水箱及安全阀的设计选型方法     

ETR Ⅱ-30调速器液压控制系统

ETRⅠ-30调速器是瑞士爱舍维斯工厂生产的具有PID调节规律的电液调速器。本文对其液压控制系统作了较详细的介绍,供有关人员参考。     

数字式液压流量阀在工程机械中的应用

数字式流量阀是一种新研制开发的数字控制式流量阀，其调速控制响应快、精度高、稳定性好，应用于工程机械液压系统，可使工程机械的操纵控制系统面临新的变革。     

贝利阀在氨厂运行情况简介

介绍贝利阀在试车及试生产期间出现的问题及解决办法，指出维护过程中应注意的事项。