Benchmark experiment of large-angle scattering reaction cross section of iron at 14 MeV using two shadow bars – Comparison of experimental results with ENDF/B-VIII –

ABSTRACT

It is important to perform neutron transport simulations with accurate nuclear data in the neutronics design of a fusion reactor. However, absolute values of large-angle scattering cross sections vary among nuclear data libraries even for well-examined nuclide of iron. Benchmark experiments focusing on large-angle scattering cross sections were thus performed to confirm the correctness of nuclear data libraries. The series benchmark experiments were performed at a DT neutron source facility, OKTAVIAN of Osaka University, Japan, by the unique experimental system established by the authors’ group, which can extract only the contribution of large-angle scattering reactions. This system consists of two shadow bars, target plate (iron), and neutron detector (niobium). Two types of shadow bars were used and four irradiations were conducted for one experiment, so that contribution of room-return neutrons was effectively removed and only large-angle scattering neutrons were extracted from the measured four Nb reaction rates. The obtained experimental results were compared with calculations for five nuclear data libraries including JENDL-4.0, JEFF.-3.3, FENDL-3.1, ENDF/B- VII, and recently released ENDF/B-VIII. It was found from the comparison that ENDF/B-VIII showed the best result, though ENDF/B-VII showed overestimation and others are in large underestimation at 14 MeV.     

基于神经网络和遗传算法的锭子弹性管性能优化

为得到减振弹性管对下锭胆的支承弹性和锭子高速运动下的稳定性等性能的最优匹配效率,依据减振弹性管的等效抗弯刚度及底部等效刚度系数公式,利用MatLab数值分析软件构建弹性管抗弯刚度和底部挠度数学模型。首先,结合Isight优化软件基于径向基神经网络构建其近似模型,且使精度达到可接受水平,并以模型的关键结构参数弹性模量、螺距、槽宽、壁厚为设计变量,结合遗传算法对弹性管抗弯刚度和底部挠度进行多目标优化设计,得到Pareto最优解集和Pareto前沿图,确定出减振弹性管结构工艺参数的优化方案。通过对优化数据进行分析发现,该方案在保证减振弹性管弹性的同时,其底部振幅明显减弱。     

Compressive properties of pristine and SiC-Te-added MgB2 powders,green compacts and spark-plasma-sintered bulks

Pristine and (SiC+Te)-added MgB₂ powders, green and spark plasma sintered (SPS) compacts were investigated from the viewpoint of quasi-static and dynamic (Split-Hopkinson Pressure Bar, SHPB) compressive mechanical properties The amount of the additive (SiC+Te) was selected to be the optimum one for maximization of the superconducting functional parameters. Pristine and added MgB₂ show very similar compressive parameters (tan δ, fracture strength, Vickers hardness, others) and fragment size in the SHPB test. However, for the bulk SPSed samples the ratio of intergranular to transgranular fracturing changes, the first one being stronger in the added sample. This is reflected in the quasi-static K_IC that is higher for the added sample. Despite this result, sintered samples are brittle and have roughly similar fragmentation behavior as for brittle engineering ceramics. In the fragmentation process, the composite nature of our samples should be considered with a special focus on MgB₂ blocks (colonies) that show the major contribution to fracturing. The Glenn-Chudnovsky model of fracturing under dynamic load provides the closest values to our experimental fragment size data.     

On the linear correlation between microhardness and mechanical properties in polar polymers and blends

The tensile elastic modulus (E), yield stress (σ_Y) and microhardness (MH) of neat and binary and ternary blends of glassy semicrystalline ethylene–vinyl alcohol copolymer (EVOH), a glassy amorphous polyamide and a semicrystalline nylon‐containing ionomer covering a broad range of properties were examined. The tests were carried out on dry and water‐equilibrated samples to produce stiffer and softer materials, respectively. From the results, more accurate linear correlations were found to describe adequately the microhardness, modulus and yield stress of these strongly self‐associated polymers through hydrogen bonding. Copyright © 2003 Society of Chemical Industry     

先张法预应力桥梁板施工工艺及应用实例

结合太原市向阳店桥梁板施工实例，介绍了采用先张法进行预应力桥梁板施工的过程。阐述了桥梁板的施工工艺，该工艺实现了整体张拉、整体放张，使钢绞线逐根受力均匀，施工速度快，能保证梁端的质量。指出拉杆系统的使用，降低了成本，增加了效益。     

Network topology and the theory of rubber elasticity

The earliest investigations on rubber elasticity, commencing in the 19th century, were necessarily limited to phenomenological interpretations. The realisation that polymers consist of very long molecular chains. commencing c. 1930, gave impetus to the molecular theory of rubber elasticity (1932-). according to which the high deformability of an elastomer, and the elastic force generated by deformation, stem from the configurations accessible to long molecular chains. Theories of rubber elasticity put forward from 1934-1946 relied on the assumption that the junctions of the rubber network undergo displacements that are affine in macroscopic strain. The theory of James and Guth (1947) dispensed with this premise, and demonstrated instead that the mean positions of the junctions of a ‘phantom’ network consisting of Gaussian chains devoid of material properties are affine in the strain. The vital significance of the distinction between the actual distribution of chain vectors in a network and their distribution if the junctions would be fixed at their mean positions went unnoticed for nearly 30 years. Experimental investigations, commencing with the incisive work of Gee in 1946. revealed large departures from the relationship of stress to strain predicted by the theories cited. This discrepancy prompted extensive studies, theoretical and experimental, during succeeding years. Inquiry into the fundamentals of polymer networks, formed for example by interlinking very long polymer molecules, exposed the need to take account of network imperfections, typically consisting of chains attached at only one end to a network junction. Various means were advocated to make corrections for these imperfections. The cycle rank ζ of the network has been shown (1976) to be the fundamental measure of its connectivity, regardless of the junction functionality and pattern of imperfections. Often overlooked is the copious interpenetration of the chains comprising typical elastomeric networks. Theories that attempt to represent such networks on a lattice are incompatible with this universal feature. Moreover, the dense interpenetration of chains may limit the ability of junctions in real networks to accommodate the fluctuations envisaged in the theory of phantom networks. It was suggested in 1975 that departures from the form predicted for the elastic equation of state are due to constraints on the fluctuations of junctions whose effect diminishes with deformation and with dilation. Formulation of a self-consistent theory based on this suggestion required recognition of the non-affine connection between the chain vector distribution function and the macroscopic strain in a real network, which may partake of characteristics of a phantom network in some degree. Implementation of the idea was achieved through postulation of domains of constraint affecting the equilibrium distribution of fluctuations of network junctions from their mean positions. This led in due course to a theory that accounts for the relationship of stress to strain virtually throughout the ranges of strain accessible to measurement. The theory establishes connections between structure and elastic properties. This is achieved with utmost frugality in arbitrary parameters.     

Axial vibrations of U-shaped bellows with elastically restrained end conditions

Previous work by Li et al. in the area of axial vibrations of bellows dealt with fixed end conditions. However, it is seen on several occasions that bellow ends are welded to a small pipe spool that has a lumped mass such as a valve or an instrument. Hence, the present paper aims at finding out the effect of elastically restrained ends on the axial natural frequencies. The analysis considers finite stiffness axial restraints on the bellows, i.e. solving the set of equations with non-homogeneous boundary conditions. Two bellow specimens are considered for comparison having the same dimensions as taken by Li in his analysis. The transcendental frequency equation deduced is accurate as the first, second and third mode frequencies computed are in close agreement to the ones obtained by Li.     

植筋施工工艺

以某网球馆改造工程为例 ,就植筋技术的概念及所用材料进行了介绍 ,详细阐述了其施工工艺流程及措施 ,指出植筋技术具有工艺简单、操作方便、造价相对较低等优点     

A direct stiffness analysis of a composite beam with partial interaction

The use of the conventional semi-analytical stiffness method in finite element analysis, in which interpolation polynomials are used to develop the stiffness relationships, leads to problems of curvature locking when beam-type elements are developed for composite members with partial interaction between the materials of which it is comprised. The curvature locking phenomenon that occurs for composite steel–concrete members is quite well reported, and the general approach to minimizing the undesirable ramifications of curvature locking has been to use higher-order polynomials with increasing numbers of internal nodes. This paper presents an alternate formulation based on a direct stiffness approach rather than starting from pre-defined interpolation polynomials, and which does not possess the undesirable locking characteristics. The formulation is based on a more general approach for a bi-material composite flexural member, whose constituent materials are joined by elastic shear connection so as to provide partial interaction. The stiffness relationships are derived, and these are applied to a simply supported and a continuous steel–concrete composite beam to demonstrate the efficacy of the method, and in particular its ability to model accurately both very flexible and very stiff shear connection that causes difficulties when implemented in competitive semi-analytical algorithms. Copyright © 2004 John Wiley & Sons, Ltd.