Reduction of waste biosolids by RAS-ozonation: Model validation and sensitivity analysis for biosolids reduction and nitrification

Biosolids reduction model by return activated sludge ozonation was validated by simulating nitrification data compiled from our pilot-scale and the literature studies. Then, a global sensitivity analysis (GSA) was performed to identify influential and non-influential parameters for biosolids reduction efficiency, change in specific nitrification activity (SNA), and alteration to expected nitrification stability. In general, the model outputs were sensitive to operational and ozone reaction parameters, but not to biochemical parameters. For operational parameters, mainly temperature and initial solids retention time (SRT) influenced all model outputs. For biosolids reduction, increase in the degradability of the influent COD decreased the reduction efficiency. For SNA, the changes were highly dependent on the influent TKN/COD ratio. Our findings also imply that the stability of the nitrification process in ozonated systems should be enhanced at constant MLVSS for warm temperatures, but could be reduced at temperatures below 12 °C and aerated SRTs below 10 days.     

Resistance reduction effect of potassium bismuth titanate doping in yttrium–manganese co-doped medium Curie temperature barium titanate lead free ceramics through improved synthesis process

Through improved synthesis process, resistance reduction effect of (K_0.5Bi_0.5)TiO₃ (KBT) doping in Y–Mn co-doped BaTiO₃ (BT) lead free ceramics was investigated. By different doping methods (doping K₂O, Bi₂O₃ and TiO₂ or synthesized KBT), medium Curie temperature (around 130 °C) lead free BT ceramics were obtained with ultra-low resistivity (13.84 Ωcm) with a temperature maintaining process at 700 °C. In this contribution, effect of sintering process and doping methods is discussed in detail.     

Correlation between instrumental texture and colour quality attributes with sensory analysis of selected cheeses as affected by fat contents

This study evaluated several physical and sensory parameters of different types of cheese available in the Polish market. The measurements of textural properties were conducted in an Instron universal testing machine, while the colour properties of cheeses were measured using a Minolta chromameter. The chemical composition was determined by means of the near‐infrared spectroscopy (NIRs). Moreover, a trained sensory panel was invited to assess the cheese texture‐related properties. Generally, cheeses with reduced fat content were characterised by higher hardness, adhesiveness, cohesiveness and elasticity. Texture‐related parameters of cheese with canola oil were comparable to that of most of full‐fat cheeses. The correlation analysis between physical and sensory attributes related to cheese textural properties indicated the potential applications of TPA, shear and penetration tests (r = 0.766, r = 0.75 and r = 0.765, respectively) for the evaluation of sensory properties related to the hardness. Meanwhile, the elasticity of cheese obtained from sensory evaluation was strongly correlated with the elasticity determined from the shear test (r = 0.722) and moderately correlated with the elasticity from penetration test (r = 0.588), indicating a need to refine the method of penetration test. In addition, cheeses exhibited higher meltability during convection heating at 230 °C than microwave heating. The values of meltability for cheese with reduced fat content were lower than those of full‐fat cheese.     

Graph-based video fingerprinting using double optimal projection

A double optimal projection method that involves projections for intra-cluster and inter-cluster dimensionality reduction are proposed for video fingerprinting. The video is initially set as a graph with frames as its vertices in a high-dimensional space. A similarity measure that can compute the weights of the edges is then proposed. Subsequently, the video frames are partitioned into different clusters based on the graph model. Double optimal projection is used to explore the optimal mapping points in a low-dimensional space to reduce the video dimensions. The statistics and geometrical fingerprints are generated to determine whether a query video is copied from one of the videos in the database. During matching, the video can be roughly matched by utilizing the statistics fingerprint. Further matching is thereafter performed in the corresponding group using geometrical fingerprints. Experimental results show the good performance of the proposed video fingerprinting method in robustness and discrimination.     

一种基于混沌同步的噪音衰减算法

论文提出了一种混沌通信系统的噪音衰减算法,该算法利用混沌同步现象在接收端获得正确的噪音估计值,从而从接收信号中滤除噪音恢复出正确的信号。通过数值仿真试验表明该方法是可行的。     

井下乳化/水热催化裂解复合降黏开采稠油技术研究

实验考察了胜利孤东稠油井下催化水热裂解和乳化/催化水热裂解降黏效果。所用催化剂为水溶性铁镍钒体系,Fe3+∶Ni2+∶VO4+=5∶1∶1,100 g稠油与30 g 0.5%催化剂水溶液在240℃反应24小时。原始黏度(50℃)11.0和8.36 Pa.s的两种稠油裂解并静置除水后,黏度降低76.2%和75.6%,室温放置60天后降黏率下降小于3个百分点,气相色谱显示裂解后轻组分明显增加,红外光谱显示稠油组分发生脱羧反应且芳环数减少。讨论了稠油催化水热裂解反应机理。所用化学助剂JN-A在油水中均可溶,耐温达250℃,耐矿化度达50 g/L,其水溶液以30∶100的质量比与稠油混合时形成低黏度的O/W乳状液。当水相含1.0%JN-A和0.5%催化剂时,两种稠油水热裂解后的反应混合物为O/W乳状液,黏度仅为319和309 mPa.s,静置除水后的稠油降黏率增加到86.5%和87.3%,其中的轻组分含量进一步增加。该井下乳化/催化水热裂解复合降黏法成功地用于孤东两口蒸汽吞吐井,稠油井作业后初期采出的原油黏度由~9 Pa.s降低到1 Pa.s左右,随采油时间延长而逐渐升高,约50天后超过4Pa.s。图2表6参5。     

一种制氢预转化催化剂还原的新方法

对上海高桥分公司2×10~4m~3/h(标准状态)制氢装置原设计的预转化催化剂还原流程进行了改进。先跳开预转化反应器,利用转化炉制取氢气,再用自产的高纯氢气代替重整氢,对预转化催化剂进行单独升温还原,避免了催化剂在还原初期因发生甲烷化反应而超温失活的问题,使催化剂具有更好的活性和稳定性。     

Fastmet工艺评述

介绍了Ｆａｓｔｍｅｔ工艺及发展状况，并对工艺特点和指标进行了分析。使用冷固结含碳球团和转底炉使该工艺可直接采用粉矿和提高生产效率，但因硫含量高、铁品位低而产品质量较差。不过投资和生产成本与传统工艺比较却占有较大优势。     

Nitric oxide reduction and carbon monoxide oxidation over carbon-supported copper-chromium catalysts

Carbon supported copper-chromium catalysts are shown to be very active for both the reduction of nitric oxide with carbon monoxide and the oxidation of carbon monoxide with oxygen. Mixed copper-chromium oxide active phases have good activity in the simultaneous removal of nitric oxide and carbon monoxide from exhaust gases. The influence of several catalyst variables has been investigated. The activity per volume of catalyst increases with increasing loading, while the intrinsic activity shows a maximum around C/M=100−50. An optimum catalyst for nitric oxide reduction and carbon monoxide oxidation has a copper/chromium ratio of 2/1. The apparent activation energy for the carbon monoxide oxidation over carbon supported copper-chromium catalysts is 77 kJ/mol, suggesting that the Cu---O bond rupture is the rate-limiting process. The reduction of nitric oxide takes place at higher temperatures. Since all catalysts have a low selectivity for molecular nitrogen formation at lower temperatures, the dissociation of nitric oxide is probably rate determining, resulting in a slightly reduced catalyst system. In an excess of carbon monoxide the reaction is first-order in nitric oxide and zero-order in carbon monoxide. Moisture inhibits the reaction by reversible competitive adsorption, whereas carbon dioxide does not. Oxygen completely inhibits the reduction of nitric oxide due to the more rapid reoxidation of the catalytic sites compared to nitric oxide. Therefore, the reduction of nitric oxide takes place only when all oxygen has been converted and, hence, is shifted to higher temperatures. As a possible consequence, the production of nitrous oxide is reduced. Nitric oxide and molecular oxygen react preferentially with carbon monoxide, so, in an excess of oxidizing component, gasification of the carbon support occurs at higher temperatures after carbon monoxide has been completely consumed.     

废钢铁代用品

优质钢材的冶炼和高水平操作指标的获得需要优良的原料作保证。直接还原铁，碳化铁和脱碳粒铁作为废钢铁代用品，已显示出其价格和品质上的优越性，并弥补了废铁数量的不足，但因其各有自身的特点，故研究其理化性质和使用性能，将为大规模生产和使用创造必要的条件。