Comprehensive numerical investigations on the thermal performance of heat recirculating micro combustor with pin fins for micro-thermal voltaic system applications

Aiming at improving the relatively low energy output and energy conversion efficiency of the micro-thermal voltaic (MTPV) system, an innovative heat recirculating micro combustor with pin fins is designed. The effects of pin fins arrangement, hydrogen/air equivalent ratio on the energy output and performance of CHMC, HMCP and HMCI are compared and investigated. The result shows that when the V_in is 6 m/s and Φ is 1.0, the emitter power of CHMC is 72.76W, and that of HCMP and HCMI micro combustor are 75.99W and 76.35W. and the emitter efficiency of CHMC, HCMP and HCMI is 41.93%, 43.26% and 44.01%. HMCI has better energy output capability compared with CHMC and HMCP. Even though, HMCI brings a higher pressure drop, it is within the acceptable range. When the V_in is 6 m/s, the pressure drop from the pin fins only accounts for 26.4% of the total pressure drop for HMCI. Through the study of equivalent ratio, it is found that HMCI has good adaptability in different equivalent ratio range. This work provides new ideas for the development of MTPV system in the future.     

Crowding as an Agronomic Factor Determining the Development of Plants and the Productivity of Linseed (Linum usitatissimum L.)

ABSTRACT

Nine sowing densities of linseed were compared in a two-year experiment. Self-regulation of the density of a linseed stand resulted in a differentiated branching of the plants. The number of capsules on a linseed shoot, as well as seeds in the capsule, and the number of seeds from the shoot were highly varied from year to year, and there is even a stronger differentiation in the weight of 1000 seeds. Linear relationships were noted between the mass of seeds from the linseed plant and the number of capsules. The yield of linseed was affected by both factors. An increasing sowing rate reduced the seed yield from the shoot and the plant. At lower seeding rates, the lateral shoots contributed in the seeds yield of the plant to a higher degree compared to the main ones.     

Design and manufacturing of mobile micro manipulation system with a compliant piezoelectric actuator based micro gripper

This paper presents a new design of mobile micro manipulation system for robotic micro assembly where a compliant piezoelectric actuator based micro gripper is designed for handling the miniature parts and compensation of misalignment during peg-in-hole assembly is done because piezoelectric actuator has capability of producing the displacement in micron range and generates high force instantaneously. This adjusts the misalignment of peg during robotic micro assembly. The throughput/speed of mobile micro manipulation system is found for picking and placing the peg from one hole to next hole position. An analysis of piezoelectric actuator based micro gripper has been carried out where voltage is controlled through a proportional-derivative (PD) controller. By developing a prototype, it is demonstrated that compliant piezoelectric actuator based micro gripper is capable of handling the peg-in-hole assembly task in a mobile micro manipulation system.     

A model- and simulation-based approach for tolerancing and verifying the functional capability of micro/nano-structured workpieces

The evaluation of functional features of manufactured workpieces is based on GO- and NO-GO-test results, which are obtained by comparing measured geometric characteristics with nominal dimensions and tolerances specified by the designer. These geometrical specifications are based on a tolerancing system, which was originally defined for the function mating capability. Against the background of upcoming lots of other new functions (like reduction of flow resistance, light absorption, reduction of friction, diffraction of light, self-cleaning or mass transmission) are to be realized with our products – particularly by micro- and nano scaled features. If the verification process will deliver the prediction of the achievable degree of functionality, the usability of a part can be assessed more accurately and in consequence quality and economics can be improved. So, a new principle for tolerancing and verifying turns out to be necessary. In this paper the fundamental deficit of the actual tolerancing and specification systems GPS and ASME Y14.5 is derived and the path for enlarging the system by preposing a functional model is shown. To verify the functional capability of the workpieces an approach based on simulations done with the parameterized mathematical–physical model of the function is suggested. Advantages of this approach will be discussed and demonstrated by examples with microstructured inking rolls, crankshafts and injection valves.     

Effects of different carbon sources and C/N values on nonvolatile taste components of Pleurotus eryngii

Pleurotus eryngii, the second largest industrial cultivation mushroom in China, is usually cultivated on substrates mainly consisting of sawdust and corncob. In this study, experiments were performed to determine the effects of different carbon sources and C/N values on nonvolatile taste components of P. eryngii. The effects of different carbon sources on nonvolatile taste components levels revealed that sawdust was beneficial to high levels of crude protein, amino acids, 5′‐nucleotides and equivalent umami concentration, while corncob was beneficial to high contents of carbohydrate, polysaccharides and trehalose. At the similar C/N values, relatively higher sawdust content was beneficial to umami amino acid production, while relatively higher corncob content was beneficial to high contents of carbohydrate, polysaccharides and mannitol. Higher C/N value was beneficial to high levels of crude protein, amino acids, 5′‐nucleotides and equivalent umami concentration, while lower C/N value was beneficial to high contents of carbohydrate, polysaccharides and trehalose. These results provided information for P. eryngii fruit body industrial cultivation to obtain specific nonvolatile taste components with high levels.     

一种宽带矢量调制器的设计及其应用

矢量调制器是一种可以同时控制微波信号幅度和相位的器件。本文介绍了一种基于新型微带定向耦合器的宽带矢量调制器。新的耦合器结构克服了传统微带耦合器耦合度低、方向性差的问题,也不需要Lange耦合器复杂的加工工艺,在平衡放大器、移相器和衰减器等场合具有广泛的应用。其次,研究了用串联电感对衰减器中PIN二极管的寄生参数进行补偿的一种简单方法,以改善衰减器衰减量变化时的相位性能。该方法原理简单,可在一定带宽内替代复杂的平衡结构,并给出相近的性能。最后给出了矢量调制器的测试结果和它在自适应天线阵等实际系统中的应用情况,并讨论了用于提高载波和边带抑制、满足高精度要求的校准方法。     

Revised Estimates of Dimension and Exercise Variance Components in Assessment Center Postexercise Dimension Ratings.

The authors reanalyzed assessment center (AC) multitrait-multimethod (MTMM) matrices containing correlations among postexercise dimension ratings (PEDRs) reported by F. Lievens and J. M. Conway (2001). Unlike F. Lievens and J. M. Conway, who used a correlated dimension-correlated uniqueness model, we used a different set of confirmatory-factor-analysis-based models (1-dimension-correlated Exercise and 1-dimension-correlated uniqueness models) to estimate dimension and exercise variance components in AC PEDRs. Results of reanalyses suggest that, consistent with previous narrative reviews, exercise variance components dominate over dimension variance components after all. Implications for AC construct validity and possible redirections of research on the validity of ACs are discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Micro assembly injection moulding

Injection moulding is established as one of the most common manufacturing processes of thermoplastics due to its high degree of automation and the short cycle times. Micro injection moulding is a rapidly growing technology that allows for the efficient production of very complex micro parts in high series. The “Market Analysis for Microsystems II 2002–2005” of the Nexus Task Force anticipates a yearly growth in the field of micro system technology of about 20% (Wechsung et al. 2002). This study identifies in addition to the continuous miniaturization the growing use of polymers in micro systems (Schneider et al. 2001). No other material group offers this wide range of material properties and permits to choose processing parameters and application properties according to necessities (Gächter 2000). While the production processes of micro technical components are mainly controllable, the assembly of these components to hybrid micro systems is a bottleneck to the industrial large scale production. The assembly itself represents a large fraction of the added product value and gains in importance with growing complexity and miniaturization of the systems.     

Finite element analysis of femoral components paper III – hip joints

Finite element analysis of the hip implant is conducted in this paper for representative femoral cross-section geometries and development of stress in the presence of bone cement is elucidated. Differences in cement stresses generated by varying implant cross-sections were compared with conventional features derived from representative implants. The analysis was performed under idealized implant assemblies by constraining the implant movement in the assembly. The cross-sections and implant geometries used are generic and intended to be representative of available geometries. This paper is a part of student research projects, prepared from a series of activities in biomedical implant research currently underway at Ohio Northern and Arkansas Tech Universities.