化学镀非晶态Ni—B合金的研究

本文通过化学镀方法在铜和钢上沉积非晶态Ni-B合金。着重讨论了还原剂浓度、络合剂浓度对化学镀沉积速率的影响;分析了它的耐蚀原因和其显微硬度随退火温度的变化情况并就其应用和发展略作说明。     

Influence of inhibitor addition on the corrosion protection performance of sol–gel coatings on AA2024

Sol–gel films are actively investigated during the last decade as possible candidates for environmentally friendly pre-treatments. However, the important drawback in this case is the lack of active corrosion protection and self-healing ability.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Comparison between photocatalytic ozonation and other oxidation processes for the removal of phenols from water

Photocatalytic ozonation (1O₃ + VUV + TiO₂), ozonation (O₃), catalytic ozonation (O₃ + TiO₂), ozone photolysis (O₃ + VUV), photocatalysis (TiO₂ + VUV) and photolysis (VUV) have been compared in terms of formation of intermediates, extent of, mineralization (TOC, COD, chloride, nitrate) and kinetics in the aqueous treatment of three phenols (phenol, p‐chlorophenol and p‐nitrophenol). In all cases, photocatalytic ozonation led to lower degradation times for chemical oxygen demand and total organic carbon removal. Intermediates formed were similar in the different oxidation systems with some exceptions. They can be classified into three different types: polyphenols (resorcinol, catechol, hydroquinone), unsaturated carboxylic acids (maleic and fumaric acids) and saturated carboxylic acids (glyoxylic, formic and oxalic acids). First order kinetic equations have been checked for the oxidation processes studied in the case of the parent compound. Rate constants of these systems have also been calculated. Copyright © 2005 Society of Chemical Industry     

钛容器的特点

根据钛材的化学、物理、力学和工艺性能介绍了钛容器在设计、制造、检验和应用方面的特点。     

用过滤工艺全面提高铸锭质量

探讨了过滤器孔径对6063铝合金铸锭组织和性能的影响规律。在此基础上指出,在过滤工艺恰当时,不仅可以减少铸锭中的夹杂物,而且可以有效地防止裂纹、羽毛晶等连续铸锭中的常见缺陷。     

复合聚全氟乙丙烯材料的介电及高频击穿性能研究

在聚全氟乙丙烯(FEP)中添加 TiO_2和 Al_2O_3,通过热压成型的方法制备了 FEP/TiO_2复合材料和 FEP/Al_2O_3复合材料,研究了氧化物添加量对复合材料介电常数、介电损耗和高频击穿性能的影响。结果表明,随氧化物含量的增加,复合材料的介电常数和介电损耗均增加;在同一添加量下,TiO_2对复合体系的介电性能影响较大。FEP/TiO_2复合材料的高频击穿性能随 TiO_2含量的增加而下降,在 TiO_2含量为4.0%(质量分数,下同)时,复合材料的损伤阈值已降为 FEP 材料损伤阈值的48.9 %。而 FEP/Al_2O_3复合材料的高频击穿性能随 Al_2O_3含量的增加而升高,当 Al_2O_3含量为1.2%时,复合材料的损伤阈值已增大到 FEP 材料损伤阈值的2倍,达到313 J/m~2。     

Monte Carlo simulation of hydrogen absorption in palladium and palladium–silver alloys

A modified Monte Carlo (MC) simulation was performed to investigate the hydrogen absorption behavior in Pd and Pd–Ag alloys of the composition Pd_xAg_1−x (x=0.7–0.8) under H₂ pressure (0.1 MPa) at different temperatures. The present method employed can consider the dissociative adsorption of hydrogen molecule and the subsequent absorption of hydrogen atom by formalizing the relationship between the pressure of hydrogen molecule and hydrogen atom. The potential parameters were determined to reproduce the solution enthalpy of hydrogen in pure metals. The results are in good agreement with experimental findings as well as previous theoretical studies. We confirmed that our method is useful to simulate the absorption of hydrogen in metals and alloys.     

过共晶铝硅合金细化初晶硅的研究

研究了ZL8604过共晶铝硅合金初晶硅细化剂和加入方式与加入量以及影响细化效果的冶铸工艺因素,实验结果达到了技术指标要求。     

The influence of NaCl and CO2 on the atmospheric corrosion of magnesium alloy AZ91

The influence of NaCl and CO₂ on the atmospheric corrosion of magnesium alloy AZ91 is studied in the laboratory. Samples were exposed under carefully controlled air and flow conditions; the relative humidity was 95%, the temperature was 22.0°C and the concentration of CO₂ was < 1 ppm or 350 ppm. Different amounts of sodium chloride (0–70 μg/cm²) were added before exposure. The corrosion products were analyzed by gravimetry, ion chromatography, X‐ray diffraction and scanning electron microscopy. Mass gain and metal loss results are reported. The combination of high humidity and NaCl is very corrosive towards AZ91. However, the NaCl‐induced corrosion is inhibited by ambient concentrations of CO₂. Exposure in the absence of CO₂ gives rise to heavy pitting, with brucite, Mg(OH)₂, being the dominant corrosion product. In the presence of CO₂ a layer of hydrated magnesium hydroxy carbonate, Mg₅(CO₃)₄(OH)₂ · 5 H₂O forms. A tentative corrosion mechanism is presented that explains the behavior in the two environments.