Interactions of Li2O volatilized from ternary lithium-ion battery cathode materials with mullite saggar materials during calcination

In recent years, the rapid development of Li(Ni_xCo_yMn_1-x-y)O₂ (LNCM) materials for application in ternary lithium-ion batteries has led to an increased demand for refractory kiln saggars in industries. However, saggars used for firing ternary Li-ion battery cathode materials are often subjected to severe corrosion and spalling. To investigate the damage mechanism of the saggar materials, non-contact corrosion experiments were designed to study the effects of the precursor additions, calcination temperature, and number of calcinations during the interaction between mullite saggar and LNCM materials. The phase composition and microstructure of the mullite saggar specimens before and after corrosion were characterized using X-ray diffraction and scanning electron microscopy, respectively, to obtain a comprehensive understanding of the causes of the deterioration of mullite saggar materials during corrosion.     

A novel design for humidifying an open-cathode proton exchange membrane fuel cell using anode purge

The low performance of open-cathode proton-exchange-membrane fuel cells (OCPEMFCs) is attributed to the low-humidity ambient air supplied to the cathode using electric fans. To improve the OCPEMFC performance, this paper proposes a novel humidification method by collecting water purged from the anode and supplying it to the open cathode. The OCPEMFC performance is evaluated at various humidifier distances from the cathode inlet, and it is compared with that where no humidifier is used when the OCPEMFC operates under three different current levels of 1, 5, and 8 A. The results show that the novel design improves the stack power, and optimal performance is achieved at a humidifier distance of 2 cm. The energy efficiency achieves an improvement between 1.4% and 1.8% when a humidifier is used.     

Synergistic effect of bulk phase doping and layered-spinel structure formation on improving electrochemical performance of Li-Rich cathode material

In this study, La was doped into the lithium layer of Li-rich cathode material and formed a layered-spinel hetero-structure. The morphology, crystal structure, element valence and kinetics of lithium ion migration were studied by field emission scanning electron microscope (FESEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). The La doped lithium-rich cathode material exhibited similar initial discharge capacity of 262.8 mAh g^?1 at 0.1 C compared with the undoped material, but the discharge capacity retention rate can be obviously improved to 90% after 50 cycles at 1.0 C. Besides that, much better rate capability and Li⁺ diffusion coefficient were observed. The results revealed that La doping not only stabilized the material structure and reduced the Li/Ni mixing degree, but also induced the generation of spinel phase to provide three-dimensional diffusion channels for lithium ion migration. Moreover, the porous structure of the doped samples also contributed to the remarkable excellent electrochemical performance. All of these factors combined to significantly improve the electrochemical performance of the material.     

轧制始极片

本文介绍了轧制法生产始极片的工艺，比较了轧制法和传统的钛种板生产始极片的优缺点，讨论了采用轧制始极片的经济效益和应用前景。     

污水汽提系统的化学除臭清洗

文章简要介绍了化学除臭清洗剂JX-518的组成,并对采用该清洗剂对污水汽提系统进行化学除臭清洗的清洗过程及注意事项进行了详细介绍。实践证明,清洗后系统残液中硫化物及氨氮可降至很低,取得了很好的清洗效果。     

CSTN-LCD用铬版清洗效果的改善

利用铬版清洗机对CSTN-LCD用铬版进行清洗处理,分析了清洗过程中出现的铬层脱落现象,铬层脱落与轴向喷射压力和水平切力密切相关,通过调整转速和喷射压力探索了安全使用条件:在转速不超过1000r/min,喷射压力低于0.5×105Pa的情况下使用铬版清洗机进行清洗是相对安全的。同时采用预清洗处理的方法满足清洁要求,使换线时间由平均3h缩短到平均1h以内,年产能提高270000片。     

牛奶加工过程中的清洗(二)

五．牛奶厂的清洗。目前，牛奶厂采用的清洗方式主要是CIP清洗(Cleaning in place)，原地清洗或称定置清洗，即在基本不拆卸或挪动机械装置和管线的情况下对生产过程中能与牛奶发生接触的设备表面进行的清洗。其冲刷、清洗、灭菌的整个过程全部实现了自动化因此大大降低了劳动强度。而有一些不     

荧光显示管直丝氧化物阴极有效逸出功的计算

阴极的逸出功是表征阴极发射能力的物理量，求定荧光显示管直丝氧化物阴极有效逸出功时，因其零场发射电流密度难于准确取值，温度无法直接测量，显得困难，须予解决，为此提出了一种计算阴极有产逸出功的办法，对某显示管的发射欠佳和“低温高效”的两种氧化物阴极的有效逸出功进行计算，有效逸出功率是靠测量相关物理量再同计算得出，精度不很高，文中所用办法也不例外，但所得结果能反映阴极发射能力，所需仪器少，是实用方法。     

点阴极电场辅助阳极连接中的紧密接触面积和电流

用等效电路的方法研究了点阴极情况下的电场辅助阳极连接效应，计算了连接电流，连接孕育期和紧密接触面积，本文结果表明，连接初期电流迅速衰减，随后缓慢变小，直至某一稳定值，孕育期随温度上升指数下降，连接温度高时，孕育期将难以观察到；待连接表面之间紧密接触面积随时间延长而非线性扩展，紧密接触区域增大时，其边界向外推进速度渐小，而接触面积增加渐快。     

燃气脉冲吹灰技术在催化裂化装置余热锅炉上的应用

吉化炼油厂催化裂化装置余热锅炉受热面采用螺旋翅片管结构，积灰严重，在第七0三研究所的积极参与合作下，哈尔滨哈宜电站设备研究研制开发了燃气脉冲吹灰装置系列产品，并应用于吉化炼油厂催化装置余热锅炉。应用结果表明，燃气脉冲吹灰装置每爆燃一个循环，余热锅炉排烟温度降低15－20℃，锅炉蒸汽产量增加1t/h，余热利用率提高3．4个百分点。