用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

Charge source and the charging mechanism of the contact electrification of polymer powder

The charge sources, as well as the charging mechanism of the contact electrification (CE) of polymers, are still debatable. Since CE is accompanied by destruction, it is considered that “hard contacting” via ball milling can induce covalent bond scission and produce naked-activated-charge sources. Regarding “soft contacting” via nano-scale sliding, which does not induce covalent bond scission, a frontier-electron, “f-electron,” of the naked-activated-charge source is crucial to electron transfer among the naked-activated-charge sources. Here, we configure naked-activated-charge-source models, naked-activated-mechano-anion, and naked-activated-mechano-cation, which are produced by mechanical energy induced heterogeneous covalent bond scission, as well as naked-activated-mechano-radicals that are produced by homogeneous covalent bond scission. Regarding “soft contacting” among naked-activated-charge sources in a vacuum, f-electron can be transferred from a donor to an acceptor if the energy level of the donor is higher than that of the acceptor. The net amount of the normalized transferred-f-electrons is obtained by adopting settings in which the average energy level of the naked-activated-charge sources (as the donors) is higher than that of the sources employed as acceptors. Thus, the surfaces comprising the donors and acceptors will exhibit positive and negative net surface charges, respectively. We conclude that net surface charges depend on the average energy level of naked-activated-charge sources. Further, we observe that the alignment of polyethylene (PE)-polyvinyl chloride (PVC)-polytetrafluoroethylene (PTFE) to the average energy level is identical to that of the triboelectric series.     

一种新型回路电阻测试仪的研究与设计

针对传统低压回路电阻测试仪只能在被测设备停电时使用的一大限制,本文提出并设计了一种新型低压回路电阻测试仪。该仪器可在低压设备运行状态下对其回路电阻进行测量,在保证测量精度的前提下减少了设备停电率,大大提高了工作效率。     

Integrated circuit and system design for renewable energy inverters

This study proposes that a novel integrated circuit (IC) and system design for renewable energy inverters can harvest renewable energy to power direct current (DC) and alternating current (AC) loads. In addition, an intelligent synthesis and management tool is developed to design the proposed system and to judge the system’s operational maintenance decisions. Finally, a renewable energy inverter’s information is posted to an online system. Users can obtain the proposed system’s information at any time and place. The accurate and superior performance of the proposed IC and system is confirmed by computer simulations and experimental results.     

面向航空通信应用的边沿触发器教学设计

研究和分析了面向航空通信应用的边沿触发器教学设计。以边沿触发电路实现原理为核心,引导边沿触发机制的探究式学习；以航空机载网络通信为具体应用背景,引入科学研究和工程实现中实际问题,设计曼切斯特码检测系统实验；使得边沿触发器教学成为“知识再创造”的过程和创新实践的新载体,以期培养新工科背景下的独立、创新和实践精神。     

关于硬件木马电路检测技术分析及发展趋势探讨

本文结合HTH电路的复杂性等特征分析与实际应用现状,研究了HTH电路的具体检测技术方法并对当前热点技术进行对比分析,探讨了HTH电路检测方法的技术发展趋势。     

A practical Equivalent Electrical Circuit model for Proton Exchange Membrane Fuel Cell (PEMFC) systems

An alternative Equivalent Electrical Circuit for Proton Exchange Membrane Fuel Cells is modelled in this study. Both I–V characteristics and H₂ consumptions corresponding to generated power under load and no-load conditions are investigated. For this purpose, H₂ consumptions and I–V characteristics of three different sized PEMFCs are tested. There is a very good harmony between the model results and measured values (relative error %0.7, %6.4 and %2.5 for FC-A, FC-B and FC-C respectively). In the proposed model current passes only on parallel resistance and not on serial resistance at no-load condition. Thus, a FC with higher parallel resistance should be preferred. Another key output of this study is that based on the proposed model, performance comparison of FCs can be performed with the parameters defined in this work. Proposals made in this study can easily be used for performance analysis of FCs under for both steady state and transient analysis.     

尿素装置液位仪表失真分析及处理

介绍了尿素装置中3起液位仪表失真案例,分析了故障现象和设备工况,确定失真原因,采取了相应的处理措施,解决了仪表故障。     

Study of planar structure applying reciprocity technique combined with MGEC and analysis of discontinuity

The 3D structure electromagnetic computation presents several difficulties related to the volume mesh. In fact, the entire volume space must be taken into account even the smallest details. In this article, we propose a formulation based on the reciprocity theorem combined with the generalized equivalent circuit method to model a planar 3D structure with both coaxial and planar excitation. The major advantage of this formulation is the fact to reduce the computational volume into 2D ones in the discontinuity plane. In addition, we focused on the calculation of the discontinuity between the excitation source and the planar structure to determine the exact behavior of the electric coaxial excitation model. The obtained current density, electric field distributions, and the input impedance are presented and discussed in the following sections. An approximately good agreement of input impedance with those obtained by the simulator and measurement is shown.     

黄浦江下游吴淞口站低潮位重现期研究

黄浦江为感潮河流,低潮位重现期的确定对黄浦江航道的设计具有重要意义。为了准确估计黄浦江低潮位的重现期,以黄浦江下游吴淞口站年最低潮位序列为例,在对样本进行三性审查的基础上,分别采用传统的数理统计方法和时变矩方法进行水文频率分析。结果表明:吴淞口站年最低潮位序列在1996年发生了变异;还现修正后的序列服从位置参数线性时变的GEV模型,低潮位存在缓慢的上升趋势;一致性条件下百年一遇低潮位约为0.261 m,在非一致性条件下其重现期增大为150 a。非一致性条件下的重现期增大说明黄浦江现有的航道设计标准偏安全,航道通航保证率提高。