New horizon in mechanochemistry—high-temperature,high-pressure mechanical synthesis in a planetary ball mill—with magnesium hydride synthesis as an example

A new route of materials synthesis, namely, high-temperature, high-pressure reactive planetary ball milling (HTPRM), is presented. HTPRM allows for the mechanosynthesis of materials at fully controlled temperatures of up to 450 °C and pressures of up to 100 bar of hydrogen. As an example of this application, a successful synthesis of magnesium hydride is presented. The synthesis was performed at controlled temperatures (room temperature (RT), 100, 150, 200, 250, 300, and 325 °C) while milling in a planetary ball mill under hydrogen pressure ($>$50 bar). Very mild milling conditions (250 rpm) were applied for a total milling time of 2 h, and a milling vial with a relatively small diameter (φ = 53 mm, V = ～0.06 dm³) was used. The effect of different temperatures on the synthesis kinetics and outcome were examined. The particle morphology, phase composition, reaction yield, and particle size were measured and analysed by scanning electron microscopy, X-ray diffraction, differential scanning calorimetry (DSC) techniques. The obtained results showed that increasing the temperature of the process significantly improved the reaction rate, which suggested the great potential of this technique for the mechanochemical synthesis of materials.     

Machine fault diagnosis with small sample based on variational information constrained generative adversarial network

In actual engineering scenarios, limited fault data leads to insufficient model training and over-fitting, which negatively affects the diagnostic performance of intelligent diagnostic models. To solve the problem, this paper proposes a variational information constrained generative adversarial network (VICGAN) for effective machine fault diagnosis. Firstly, by incorporating the encoder into the discriminator to map the deep features, an improved generative adversarial network with stronger data synthesis capability is established. Secondly, to promote the stable training of the model and guarantee better convergence, a variational information constraint technique is utilized, which constrains the input signals and deep features of the discriminator using the information bottleneck method. In addition, a representation matching module is added to impose restrictions on the generator, avoiding the mode collapse problem and boosting the sample diversity. Two rolling bearing datasets are utilized to verify the effectiveness and stability of the presented network, which demonstrates that the presented network has an admirable ability in processing fault diagnosis with few samples, and performs better than state-of-the-art approaches.     

Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.     

测井资料在优选压裂层位中的应用

压裂是低孔、低渗油层改造的主要增产措施。根据常规测井资料、岩石物理实验分析数据及试油成果。研究储层四性关系，确定区块的低孔、低渗储层评价标准。进一步对油层进行分类，有针对性地为油层压裂提供施工层位和准确的储层参数。通过商543区块实例，阐述了选择压裂层位的方法。     

大同市水资源开发利用状况与承载能力的思考

文中分析了大同市水资源开发利用的状况，并对水资源承载能力的有关问题进行了讨论。     

Magnetic Properties of Fe-Doped Rutile

Ball-milling method was applied to dissolve Fe into titanium dioxide (TiO₂). X-ray diffraction indicated the starting anatase changed to a rutile-type structure with oxygen deficiency after ball milling. Transmission electron microscopy and X-ray absorption experiments were conducted to examine the possible existence of magnetic impurities in the ball-milled powders after they were leached in HCl solutions. Temperature dependence of the resistivity shows semiconducting behavior and the magnetic hysteresis loops at 5 and 300 K exhibit ferromagnetic characteristics. Fe-doped TiO₂ films were also prepared by pulsed laser deposition. The magnetic properties of the films are discussed.     

水资源承载力及其研究

文章简要介绍了我国水资源情况,分析了我国水资源承载力与可持续发展的关系,并阐述了水资源承载力 研究的特点和方法。     

万家寨引黄工程北干1号隧洞Ⅳ标155-274型TBM主轴承总成组装概要

文中对万家寨引黄工程北干线1号隧洞Ⅳ标使用的155—274型TBM主轴承总成各部件组装过程及其相应的技术要求进行了概要的描述，目的是进一步熟悉155—274型TBM主轴承总成的各个部件并加深对主轴承工作原理的理解。     

压型钢板组合楼板承载力的有限元分析

压型钢板组合楼板是 2 0世纪发展起来的一种新型结构形式。它具有显著的优势 ,如轻质、高强 ,施工快捷等 ,将在未来的建筑领域中大有作为。组合楼板的承载力主要取决于钢板 -混凝土界面处的抗剪强度。建立了一个二维有限元模型来研究单向组合板的性能。并将计算结果与试验数据进行对比 ,验证了模型的有效性     

川西马井构造下白垩统含气性识别与评价

川西马进地区下白垩统含气性识别在测井解释上 ,主要在于储层含气水差异分辨较困难 ,气和水在测井曲线上的响应比较接近 ,过去解释的部分气层经测试却产水 ,常规的测井解释方法很难将二者区分开。以钻井录井显示和测试结果为依据 ,利用交会图分析技术 ,成功地对储层含气、水性质进行了识别 ;利用模糊聚类分析技术对含气性差异与含水性差异进行了判别。在此基础上 ,对含气性进行评价。