Experimental investigation on the invert stability of operating railway tunnels with different drainage systems using 3D printing technology

In recent years, the invert anomalies of operating railway tunnels in water-rich areas occur frequently, which greatly affect the transportation capacity of the railway lines. Tunnel drainage system is a crucial factor to ensure the invert stability by regulating the external water pressure (EWP). By means of a three-dimensional (3D) printing model, this paper experimentally investigates the deformation behavior of the invert for the tunnels with the traditional drainage system (TDS) widely used in China and its optimized drainage system (ODS) with bottom drainage function. Six test groups with a total of 110 test conditions were designed to consider the design factors and environmental factors in engineering practice, including layout of the drainage system, blockage of the drainage system and groundwater level fluctuation. It was found that there are significant differences in the water discharge, EWP and invert stability for the tunnels with the two drainage systems. Even with a dense arrangement of the external blind tubes, TDS was still difficult to eliminate the excessive EWP below the invert, which is the main cause for the invert instability. Blockage of drainage system further increased the invert uplift and aggravated the track irregularity, especially when the blockage degree is more than 50%. However, ODS can prevent these invert anomalies by reasonably controlling the EWP at tunnel bottom. Even when the groundwater level reached 60 m and the blind tubes were fully blocked, the invert stability can still be maintained and the railway track experienced a settlement of only 1.8 mm. Meanwhile, the on-site monitoring under several rainstorms further showed that the average EWP of the invert was controlled within 84 kPa, while the maximum settlement of the track slab was only 0.92 mm, which also was in good agreement with the results of model test.     

A mineralogical approach to evaluating laboratory scale acid rock drainage characterisation tests

Effective management of the risks associated with acid rock drainage (ARD) requires the ability to identify material with a potential to generate ARD reliably. With the increasing prevalence of quantitative mineralogy (Quantitative XRD, auto-SEM), opportunity exists to use mineralogy at all stages in ARD characterisation and prediction. This study uses a mineralogical approach across the head grade samples and the residues obtained under leach conditions of several common ARD characterisation tests (Acid Neutralising Capacity, Net Acid Generation), as well as the University of Cape Town (UCT) biokinetic test to evaluate the extent to which acid-neutralising minerals react. The results show the contribution of the carbonates to the acid neutralising capacity, as well as the partial dissolution of intermediate weathering silicate minerals such as chlorite and mica.     

公路隧道喷射混凝土套拱加固结构力学特性

为研究喷射混凝土套拱加固前后二次衬砌与混凝土套拱的受力状况,依托陕西汉中至留坝段八里关隧道,运用有限元软件建立隧道混凝土结构套拱加固分析模型,并通过现场监测获取二次衬砌与套拱间的接触压力、套拱格栅拱架钢筋应力、套拱混凝土应力,将数值模拟结果与现场测试结果相结合,得出套拱结构的一般受力变化规律。结果表明:套拱加固前衬砌结构的最不利荷载位置位于施工缝附近的拱顶、拱肩与拱脚处; 由于衬砌局部变形与温度应力的影响,套拱混凝土应力变化呈现反复“上升-下降-上升”最后趋于稳定的特点; 套拱的作用是控制二次衬砌的进一步变形,套拱施作后所承受荷载较小,套拱反作用力远小于围岩作用于衬砌的应力,在应力计算中不应将衬砌与套拱作为整体计算; 套拱结构数值模拟所得的结果与现场测试套拱结构内力(轴力、弯矩)的大小及分布相似度高,但在衬砌裂损严重部位,数值模拟所得结果误差较大,应以现场测试结果为准。     

基于ANP-SWOT的上海公路废弃物资源化发展对策研究

随着公路系统的新陈代谢，大量废弃物给城市的资源与环境协调发展带来了巨大压力，以沥青路面再生技术为路径的公路废弃物资源化符合循环经济的理念，是我国公路建设迈向生态文明的必然选择。通过 ANP-SWOT 对上海公路废弃物资源化发展战略进行实证分析，发现当前形势下其优势和机遇较为明显，确定以 SO 策略为核心的推广战略为最佳选择，并提出一系列配套发展策略，为推动上海公路废弃物资源化提供参考。     

普通稠油油藏启动压力梯度求解方法与应用

利用微观尺度管流模型,结合普通稠油流变特征,提出了在考虑稠油流变性条件下微观启动压力梯度计算方法.对渤海渤中18块不同渗透率岩心进行室内驱替实验,通过对实验数据的回归分析,得到不同粘度普通稠油油藏启动压力梯度与地层平均渗透率关系,并绘制了启动压力梯度的图版.将研究结果应用于普通稠油油藏,给出了利用启动压力梯度确定极限泄油半径及合理井距的理论计算方法.     

射孔枪+内置式压力计托筒+水力泵新三联作试油(测试)工艺技术在大港油田研制与应用

该工艺技术是在原三联作(TCP+MFE+JET)基础上,根据大港油田勘探试油(测试)的需要,研制开发出的又一新技术,与原三联作相比,一趟管柱不但完成求产、测压、泵排工作,而且还能进行酸化等措施,提高了资料品质,减少了作业成本。经过6井次现场应用,全部达到了设计要求,取得了工艺、资料、成本、速度的较大进步,具有较高推广应用价值。     

Collection Conduits Including Subsurface Drains

Numerous types of pipes and channels with spatially increasing flows in environmental engineering applications are identified by type and function and referred to as collection conduits. An overview of methods for designing and analyzing collection conduits is provided. Full conduits with nonuniform and uniform inflow are first considered. Dimensional analysis is then employed to demonstrate the relationship between variables for open channels; that leads to the identification of possibilities for generalized numerical solutions. Prior collection conduit applications are discussed within the framework of the dimensional analysis (which also pertains to some constant-flow applications). A previously unpublished generalized numerical solution for rectangular collection conduits is presented. Subsurface drains are addressed with particular emphasis, including the use of numerical methods to develop a new generalized chart and relation to other design methods. Among the important conclusions for subsurface drains is that the somewhat common practice of using Manning’s equation alone for such problems is not generally adequate. Examples and practical design suggestions are included, and the use of computer-based numerical methods is discussed more generally.     

Inhibition of acid rock drainage from uranium ore waste using a conventional neutralization and precipitation treatment

Glass columns (length 50 cm, i.d. 4 cm) containing 900 g of uranium ore waste were subjected to a three-step process: (1) acid drainage generation, (2) neutralization and precipitation treatment and, again, (3) acid drainage generation. In the first acid generation step, lasting about one year, different variables (pyrite addition, inoculation and irrigation solution) were tested by measuring effluent pH, redox potential, total iron and sulphate. Conditions of acid generation were satisfactorily reproduced, reaching stable pH values around 2.0 that were determined mainly by pyrite addition and the type of irrigation solution used (distilled water or ferrous sulphate). The neutralization and precipitation treatment consisted of alternating irrigations of a neutralizing solution (CaO saturated plus NaOH) and a precipitating solution (ferric sulphate saturated). This treatment caused accumulation of basic iron sulphate and iron oxide precipitates according to SEM studies. After this treatment, the barrier effect created by the reaction products was checked, using irrigation solutions similar to the first step. The effluents collected showed higher pH and lower redox potential, total iron and sulphate values than those observed before the treatment, evidencing inhibition of acid drainage generation.     

Model Validation for Bridge-Road-Vehicle Dynamic Interaction System

The dynamic response of highway bridges subjected to moving truckloads has been observed to be dependent on (1) dynamic characteristics of the bridge; (2) truck configuration, speed, and lane position on the bridge; and (3) road surface roughness profile of the bridge and its approach. Historically, truckloads were measured to determine the load spectra for girder bridges. However, truckload measurements are either made for a short period of time [for example, weigh-in-motion (WIM) data] or are statistically biased (for example, weigh stations) and cost prohibitive. The objective of this paper is to present results of a 3D computer-based model for the simulation of multiple trucks on girder bridges. The model is based on the grillage approach and is applied to four steel girder bridges tested under normal truck traffic. Actual truckload data collected using a discrete bridge WIM system are used in the model. The data include axle loads, truck gross weight, axle configuration, and statistical data on multiple presence (side by side or following). The results are presented as a function of the static and dynamic stresses in each girder and compared with code provisions for dynamic load factor. The study provides an alternate method for the development of live-load models for bridge design and evaluation.     

公路边坡培植柠条的探讨

介绍了河曲公路所处的自然环境 ,阐述了人工铲草的利与弊 ,进而提出了边坡培植柠条的效益分析 ,并对培植柠条的苗期管理及与养护生产的关系进行了介绍