用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

一种新型回路电阻测试仪的研究与设计

针对传统低压回路电阻测试仪只能在被测设备停电时使用的一大限制,本文提出并设计了一种新型低压回路电阻测试仪。该仪器可在低压设备运行状态下对其回路电阻进行测量,在保证测量精度的前提下减少了设备停电率,大大提高了工作效率。     

A practical Equivalent Electrical Circuit model for Proton Exchange Membrane Fuel Cell (PEMFC) systems

An alternative Equivalent Electrical Circuit for Proton Exchange Membrane Fuel Cells is modelled in this study. Both I–V characteristics and H₂ consumptions corresponding to generated power under load and no-load conditions are investigated. For this purpose, H₂ consumptions and I–V characteristics of three different sized PEMFCs are tested. There is a very good harmony between the model results and measured values (relative error %0.7, %6.4 and %2.5 for FC-A, FC-B and FC-C respectively). In the proposed model current passes only on parallel resistance and not on serial resistance at no-load condition. Thus, a FC with higher parallel resistance should be preferred. Another key output of this study is that based on the proposed model, performance comparison of FCs can be performed with the parameters defined in this work. Proposals made in this study can easily be used for performance analysis of FCs under for both steady state and transient analysis.     

Study of planar structure applying reciprocity technique combined with MGEC and analysis of discontinuity

The 3D structure electromagnetic computation presents several difficulties related to the volume mesh. In fact, the entire volume space must be taken into account even the smallest details. In this article, we propose a formulation based on the reciprocity theorem combined with the generalized equivalent circuit method to model a planar 3D structure with both coaxial and planar excitation. The major advantage of this formulation is the fact to reduce the computational volume into 2D ones in the discontinuity plane. In addition, we focused on the calculation of the discontinuity between the excitation source and the planar structure to determine the exact behavior of the electric coaxial excitation model. The obtained current density, electric field distributions, and the input impedance are presented and discussed in the following sections. An approximately good agreement of input impedance with those obtained by the simulator and measurement is shown.     

声波测井换能器激发响应实验研究

声波测井换能器的激发响应由换能器振动时所表现出来的动态阻抗和激发电路参数决定。而换能器的动态（阻抗）参数随压电晶体及其装配方式（力学边界条件）改变。为了测量换能器动态参数的影响，采用声波测井仪器常用的压电晶体和升压变压器，通过改变激发脉冲宽度和直流电压进行了实验，结果发现：在换能器两端的瞬态响应中，一共有三个二阶网络响应，分别对应于不同的频率。最低的一个影响声波测井波形的基线、与换能器主频接近的一个决定激发效率以及电路与压电晶体之间的匹配关系，是激发电路设计中比较关键的，其参数可以通过导纳圆测量仪器得到。     

有互感和电源的电容耦合电路的量子涨落

通过正则变换和幺正变换的方法研究了有互感和电源存在的情况下的介观电容耦合电路的量子涨落。结果表明电荷和电流的量子涨落与电源无关。当电路元件确定时，如果L1／L2的值很大或很小，耦合对涨落的影响很大。互感从有到无的过程中，回路1中电流的涨落和回路中2中电荷的涨落有明显的变化。换句话说，互感的有无对涨落的大小起着举足轻重的作用。     

正交数字上变频器AD9857的使用

介绍数字正交上变频器AD9857的原理、功能和基本使用方法以及如何通过单片机8051实现对它的编程控制。     

超宽带极窄脉冲设计与产生

超宽带(UWB)技术是以持续时间极短的脉冲作为传输载体进行数据通信的无线新技术。基于BJT雪崩特性,本文采用并行同时触发的工作方式,设计并产生了高重复速率的UWB脉冲电路发生器,极大地减少了时延,缩短了上升时间,提高了脉冲的幅度,并从等效电路法的观点分析计算了脉冲的特性参数,理论结果与实测结果具有较好的一致性。     

Molecular correlations in sheared thermotropic copolyesters showing banded textures

Banded textures produced in a thermotropic liquid crystal polymer by shearing between glass slides are examined by using both transmission electron and polarized light microscopy. The periodic variation in director orientation about the shear axis, as measured by light microscopy, is shown to be distinctly different from that indicated by electron diffraction. Measurements of birefringence and observation of Zernicke phase contrast indicate periodic variations in optical properties of the polymer, in step with the bands. Such effects are accounted for in terms of a synchronous rotation of the planar aromatic groups about the molecular chain axes. Evidence for an out-of-plane component of molecular orientation is also presented.     

Generation of Technology-Independent Retargetable Analog Blocks

This paper introduces a complete methodology for retargeting of analog cells to different sets of specifications. This methodology is technology-independent, thus allowing the migration, from one technology to another, of the circuit under retargeting. Careful integration of the device sizing and layout generation tasks via the incorporation of layout constraints during the sizing process allows to generate fully functional designs in a few minutes. The methodology is illustrated via the retargeting of a fully-differential Miller-compensated two-stage operational amplifier for a new set of specifications and two different technological processes.An erratum to this article can be found at