用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

Analysis and proposition of limiting current density measurement protocol

Limiting current density at different temperatures, backpressures, and balance gases can be used to separate molecular diffusion resistance, Knudsen diffusion resistance and local transport resistance of membrane electrode assembly (MEA). However, the measurement of limiting current density has no unified protocol. The diverse choices in the literature, either in the control of current or voltage or in the atmosphere like relative humidity and O₂ concentrations, make it difficult to compare the results and identify the true bottleneck hindering the mass transport. In this work, the current-voltage curves obtained by current scanning/stepping and voltage scanning/stepping methods under dilute O₂ of different concentrations and a wide range of relative humidity were measured and analyzed systematically. It is found that the voltage stepping method is superior to the other three ways of control for the reliable determination of the limiting current density. Aided with simultaneous electrochemical impedance spectroscopy measurement, the limiting current density can be determined with pinpoint accuracy. When the limiting current density is just used to qualitatively evaluate different MEA, the voltage scanning method can be used instead for its high time efficiency. The selection of the atmosphere also plays an important role in suppressing the distortion from excessive water and reducing the spurious contribution from proton conduction resistance. It is found that O₂ concentrations at 0.5 vol% and relative humidity at 90% can give the best estimation of O₂ transport resistance in membrane electrode assembly.     

Charge source and the charging mechanism of the contact electrification of polymer powder

The charge sources, as well as the charging mechanism of the contact electrification (CE) of polymers, are still debatable. Since CE is accompanied by destruction, it is considered that “hard contacting” via ball milling can induce covalent bond scission and produce naked-activated-charge sources. Regarding “soft contacting” via nano-scale sliding, which does not induce covalent bond scission, a frontier-electron, “f-electron,” of the naked-activated-charge source is crucial to electron transfer among the naked-activated-charge sources. Here, we configure naked-activated-charge-source models, naked-activated-mechano-anion, and naked-activated-mechano-cation, which are produced by mechanical energy induced heterogeneous covalent bond scission, as well as naked-activated-mechano-radicals that are produced by homogeneous covalent bond scission. Regarding “soft contacting” among naked-activated-charge sources in a vacuum, f-electron can be transferred from a donor to an acceptor if the energy level of the donor is higher than that of the acceptor. The net amount of the normalized transferred-f-electrons is obtained by adopting settings in which the average energy level of the naked-activated-charge sources (as the donors) is higher than that of the sources employed as acceptors. Thus, the surfaces comprising the donors and acceptors will exhibit positive and negative net surface charges, respectively. We conclude that net surface charges depend on the average energy level of naked-activated-charge sources. Further, we observe that the alignment of polyethylene (PE)-polyvinyl chloride (PVC)-polytetrafluoroethylene (PTFE) to the average energy level is identical to that of the triboelectric series.     

超宽带大功率合成器设计北大核心CSCD

在80 MHz~1 GHz频段,单个功率管输出功率能达到100 W以上,为研制输出功率400 W的功率放大器,文中设计了四路功率合成器。该合成器需要实现功率容量大、工作频带宽、体积小的设计目标。在功率容量方面,文中采用悬置带状线结构,其功率容量远远大于微带线结构;在工作频带方面,采用切比雪夫九节阻抗变换器,将工作带宽拓宽为80 MHz~1 GHz;在体积方面,文中合成器的功率合成部分采用Y型节级联实现四路功率合成,阻抗变换部分采用切比雪夫阻抗变换器进行阻抗变换,该结构相较于磁环巴伦功率合成器,不但具有损耗小、平坦度高的优点,而且通过将阻抗变换器设计成曲折的形状,进一步缩小了合成器体积。仿真与实测结果显示该合成器在80 MHz~1 GHz范围内还具有较高的平坦度,合成效率可达90%以上。     

An active balancer with rapid bidirectional charge shuttling and adaptive equalization current control for lithium-ion battery strings

This article proposes an active balancer, which features bidirectional charge shuttling and adaptive equalization current control, to fast counterbalance the state of charge (SOC) of cells in a lithium-ion battery (LIB) string. The power circuit consists of certain bidirectional buck-boost converters to transfer energy among the different cells back and forth. Owing to the characterization of the open-circuit voltage (OCV) vs SOC in LIB being relatively smooth near the SOC middle range, the SOC-inspected balance strategy can achieve more precise and efficient equilibrium than the voltage-based control. Accordingly, a compensated OCV-based SOC estimation is put forward to take into account the discrepancy of SOC estimation. Besides, the varied-duty-cycle (VDC) and curve-fitting modulation (CFM) methods are devised herein to tackle the problems of slow equalization rate and low balance efficacy, which arise from the diminution in balancing current as the SOC difference between the cells decreases in the later duration of equalization especially. The proposed strategies have taken the battery nonlinear characteristic and circuit parameter nonideality into account and can adaptively modulate the duty cycle with the SOC difference to keep balancing current constant throughout the balancing cycle. Simulated and experimental results are given to demonstrate the feasibility and effectiveness of the same prototype constructed. Compared with the fixed duty cycle and the VDC methods, the proposed CFM has the best balancing efficiency of 81.4%, and the balance time is shortened by 27.1% and 18.6%, respectively.     

基于声源定位的高校在线巡课系统设计与研究

随着网络建设以及信息化教学方法在高校教学过程中的应用普及,越来越多的高校使用在线巡课系统对教师的教学过程进行跟踪和管理,以便发现课堂教学中的亮点、问题和不足。文章提出的在线巡课系统,基于声源定位的技术,对传统的在线巡课系统做出了改进,解决了已有巡课系统中“只闻其声,不见其人”的问题,能够更直观地跟踪到教师的教学过程,包括教学行为以及师生互动过程,有效提升教务人员巡课效果和体验感受。     

Inverse identification of constitutive parameters from heat source fields: A local approach applied to hyperelasticity

In this paper, a new inverse identification method of constitutive parameters is developed from full kinematic and thermal field measurements. It consists in reconstructing the heat source field from two different approaches by using the heat diffusion equation. The first one requires the temperature field measurement and the value of the thermophysical parameters. The second one is based on the kinematic field measurement and the choice of a thermo-hyperelastic model that contains the parameters to be identified. The identification is carried out at the local scale, ie, at any point of the heat source field, without using the boundary conditions. In the present work, the method is applied to the challenging case of hyperelasticity from a heterogeneous test. Due to large deformations undergone by the rubber specimen tested, a motion compensation technique is developed to plot the kinematic and the thermal fields at the same points before reconstructing the heterogeneous heat source field. In the present case, the constitutive parameter of the Neo-Hookean model has been identified, and its distribution has been characterized with respect to the strain state at the surface of a cross-shaped specimen.     

综放高瓦斯矿井煤层瓦斯涌出量综合预测

为了成功预测竹林山煤矿综放高瓦斯矿井大采高工作面煤层瓦斯涌出量,以主采3号煤层为主要研究对象,针对3号煤层以往开采情况,通过布设测点测量其煤层瓦斯含量和了解相邻矿井瓦斯含量,采用分源预测法、回归法及统计法等预测方法得到了3号煤层瓦斯含量的分布规律,并绘制了3号煤层的瓦斯含量等值线图。对矿井不同生产时期的瓦斯含量进行预测,得到了生产前期、中期及后期采区的最大绝对瓦斯涌出量和最大相对瓦斯涌出量,说明了竹林山煤矿各个时期均属于高瓦斯矿井。     

A new design strategy for DC/DC LLC resonant converter: Concept,modeling, and fabrication

In this paper, a new design procedure for LLC converter has been introduced. In fact, this method is a computer-based design algorithm based on a numerical technique. In the process of designing, the value of the resonant element is obtained by solving the LLC converter fundamental equation. This converter will be controlled by using state feedback, such as output voltage variable. As a matter of fact, in a control system, the change of output voltage (because of load variation) will affect the switching frequency, so the output voltage will be tuned. In the designing process, the fundamental equations of LLC converter are obtained, and the value of the resonant elements is calculated. Also, a comparison analysis is carried out between the proposed and typical methods. The simulation is done to investigate the validity of the proposed method. Moreover, a prototype is manufactured, and the experimental test is done to evaluate its applicability.     

Compensation of voltage disturbances using PEMFC supported Dynamic Voltage Restorer

The continuity of supply and quality of power are the two main significant aspects of today’s power delivery system. The Dynamic Voltage Restorer (DVR) is a series connected custom power device which improves the quality of power delivered to the consumers. This paper deals with the effectual exploitation of DVR for interconnecting the proton exchange membrane fuel cell (PEMFC) stack to the grid based on optimized proportional integral (PI) and fuzzy logic (FL) Controller. The real coded Genetic algorithm (GA) is used to optimize the PI controller parameters. The PEMFC operated boost converter is used to boost up the fuel cell output voltage to balance the DC side necessities of the voltage source converter (VSC). The proposed DVR provides balanced and unbalanced voltage sag/swell compensation, harmonic reduction as well as an active power injection to the grid. The designed method also protects the sensitive loads from source side power quality disturbances including short term interruption. In addition, the harmonic compensation performance of the proposed work is validated by comparing with the results of the H^∞ controller based DVR under medium level voltage condition. The simulation results from MATLAB/SIMULINK are discussed to prove the effectiveness of the planned method.