Fabrication of alumina ceramics with functional gradient structures by digital light processing 3D printing technology

Alumina ceramics with different unit numbers and gradient modes were prepared by digital light processing (DLP) 3D printing technology. The side length of each functional gradient structure was 10 mm, the porosity ratio was controlled to 70%, and the number of units were (1 × 1 × 1 unit) and (2 × 2 × 2 unit) respectively. The different gradient modes were named FCC, GFCC-1, GFCC-2 and GFCC-3. SEM, XRD, and other characterization methods proved that these gradient structures of alumina ceramics had only α-Al2O3 phase and good surface morphology. The mechanical properties and energy absorption properties of alumina ceramics with different functional gradient structures were studied by compression test. The results show that the gradient structure with 1 × 1 × 1 unit has better mechanical properties and energy absorption properties when the number of units is different. When the number of units is the same, GFCC-2 and GFCC-3 gradient structures have better compressive performance and energy absorption potential than FCC structures. The GFCC-2 gradient structure with 1 × 1 × 1 unit has a maximum compressive strength of 19.62 MPa and a maximum energy absorption value of 2.72 × 105 J/m3. The good performance of such functional gradient structures can provide new ideas for the design of lightweight and compressive energy absorption structures in the future.     

Synthesis and characterization of a long side-chain double-cation crosslinked anion-exchange membrane based on poly(styrene-b-(ethylene-co-butylene)-b-styrene)

By choosing a triple block polymer, poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS), as the backbone and adopting a long side-chain double-cation crosslinking strategy, a series of SEBS-based anion-exchange membranes (AEMs) was successively synthesized by chloromethylation, quaternization, crosslinking, solution casting, and alkalization. The 70C16-SEBS-TMHDA membrane showed high OH⁻ conductivity (72.13 mS/cm at 80 °C) and excellent alkali stability (only 10.86% degradation in OH⁻ conductivity after soaking in 4-M NaOH for 1700 h at 80 °C). Furthermore, the SR was only 9.3% at 80 °C and the peak power density of the H₂/O₂ single cell was up to 189 mW/cm² at a current density of 350 mA/cm² at 80 °C. By introducing long flexible side chains into a polymer SEBS backbone, the structure of the hydrophilic–hydrophobic microphase separation in the membrane was constructed to improve the ionic conductivity. Additionally, network crosslinked structure improved dimensional stability and mechanical properties.     

Genetic diversity by AFLP analysis within Jatropha curcas L. populations in the State of São Paulo,Brazil

The genetic diversity of 5 populations of Jatropha curcas L. (Euphorbiaceae), a species cultivated in tropical countries and used in biodiesel production, was analyzed by amplified fragment length polymorphism (AFLP). Plants from distinct populations found in the State of São Paulo, Brazil, had their genetic diversity characterized by using three primer combinations. The number of polymorphic bands obtained reached 184 and the base pair length of bands ranged from 75 to 350, with average PIC values of 0.418. Accessions from the Aguas de Santa Barbara population presented the highest percentage of polymorphic loci (89.76%), followed by the populations of Catanduva (84.24%), Jales (80.98%), Jurucê (78.80%) and Taquaritinga (70.65%). Plants collected from the populations of Taquaritinga and Jales presented the smallest and highest genetic diversities, respectively, measured by using both Nei's genetic variability index (h = 0.2242 and 0.2973) and Shannon's index (I = 0.3359 and 0.4319). The results obtained indicated that 73.1% of genetic variability corresponds to intrapopulational variation and 26.8% to variation among populations. The clustering dendrogram using Jacquard showed four clusters. Three clusters with low genetic diversity grouped most of individuals collected in distinct regions (63.3% JU, 47.0% JA and 82.5% TA) and the fourth with the higher genetic diversity was composed with basically individuals collected in CA and AS, but it also had samples collected in JU, JA and TA, where it is possible to select individuals to be included in breeding programs.     

Fluoride-mediately solvothermal synthesis and tunable photocatalytic selectivity of urchin-like ZrO2 hollow microspheres

Photocatalysts often show excellent performances on the basis of their surface state of exposed faces with high reactivity, but unfortunately surfaces of this type are usually concealed into the interior of crystals for their high surface energy. We report here a possibility that for fluorine-terminated surfaces of monoclinic ZrO₂, these higher-energy surfaces could be retained and exposed. Urchin-like ZrO₂ hollow microspheres (UZHS) composed of nanoribbons with exposed (010) facets are obtained through a fluoride mediately solvothermal method. We prove the stabilization effect of fluorine adsorption on (010) facets by density functional theory calculations. More interestingly, UZHS exhibit tunable photocatalytic selectivity in dye degradation. The fluorinated UZHS exhibit good performances both on decomposing Congo red (CR) and methylene blue, while the surface-modified UZHS by calcination only favor decomposition of CR.     

Calorimetric study of ytterbium orthovanadate YbVO4 polycrystalline ceramics

The heat capacity of ytterbium orthovanadate was first measured by adiabatic calorimetry in the temperature range T?=?12.28–344.06?K. No obvious anomalies were observed on the curve obtained. The values of standard thermodynamic functions in the temperature range T?=?0–400 K were calculated. Based on low-temperature calorimetry data obtained, previously published data on the high-temperature heat capacity of ytterbium orthovanadate were corrected. The anomalous contribution to heat capacity for YbVO₄ was compared with the data known for YbPO₄.     

Functional substrates for the gradual release of agents

This work describes the functionalization of a natural and a man-made textile substrate, namely cotton and polyamide 6.6, with inclusion agents, β-cyclodextrins (β-CDs) that are able to release gradually to the user active ingredients. In this study we used aescin (aesculus hippocastanum extract), which is a natural agent with benefits for the treatment of varicose veins.¹H NMR and UV–vis data supported the role of β-CDs as an aescin complexing agent, and the covalent nature of the linkage between β-cyclodextrins and the textile substrates, which showed a wash fastness to more than 45 washing cycles.     

Polymer electrolytes and interfaces in solid-state lithium metal batteries

The polymer electrolyte based solid-state lithium metal batteries are the promising candidate for the high-energy electrochemical energy storage with high safety and stability. Moreover, the intrinsic properties of polymer electrolytes and interface contact between electrolyte and electrodes have played critical roles for determining the comprehensive performances of solid-state lithium metal batteries. In this review, the development of polymer electrolytes with the design strategies by functional units adjustments are firstly discussed. Then the interfaces between polymer electrolyte and cathode/anode, including the interface issues, remedy strategies for stabilizing the interface contact and reducing resistances, and the in-situ polymerization method for enhancing the compatibilities and assembling the batteries with favorable performances, have been introduced. Lastly, the perspectives on developing polymer electrolytes by functional units adjustment, and improving interface contact and stability by effective strategies for solid-state lithium metal batteries have been provided.     

A Novel Approach to Analyzing the Occupancy of the Geo/Geo/∞ Queueing System

Discrete time queueing systems have been successfully used to model packet queues in computer and digital communications systems. In this article we introduce a novel approach to analyzing the Geo^X/Geo^Y/∞ queueing system, which is suitable for modelling high speed computer and communications systems. The approach is based on characterizing the system by a functional equation which is then solved recursively to give identical results to those obtained using other approaches.     

Pyrolysis of Miscanthus Giganteus and wood pellets: TG-FTIR analysis and reaction kinetics

Characterisation of two biomass fuels (pelletised Miscanthus Giganteus and wood) was performed using thermogravimetric analysis with measurement of products by means of Fourier transform infrared spectroscopy (TG-FTIR). Three heating rate profiles were applied (10, 30 and 100 °C/min), with a final temperature of 900 °C. HCN and HNCO were found to be the major N-products, while the NH₃ fraction was detected to a minor extent. Kinetic parameters were obtained from the TG-FTIR results using a model based on parallel first-order reactions with a Gaussian distribution of activation energies. On the basis of the above kinetic analysis and product yields, input files for the functional group-devolatilisation, vaporisation, cross-linking biomass-pyrolysis model were prepared. The fit of model parameters to TG-FTIR product-evolution data was found to be generally good, but the model-predicted yields for some species did not fit experimental data at all heating rates. Further improvements in the model are needed to resolve above difficulty.     

金属/Al2O3基纳米复合材料研究最新进展

金属／Al2O3纳米复合材料在保持原有金属的功能特性时，还可以获得 很好的力学性能，是有良好发展前景的一种纳米复合材料。本文回顾了近年来金属／Al2O3基纳米复合材料在制备工艺，微观结构和力学性能，增韧强化机理方面的最新进展，并指出了今后的研究方向。