Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

直接氯化法合成对硝基氯化苄

介绍了以对硝基甲苯和氯气为原料 ,在催化剂存在下合成对硝基氯化苄的方法 ,考察了催化剂种类、反应温度、溶剂配比等因素对反应的影响 ,优化的反应条件为 :对硝基甲苯用量 1 3 7g,对硝基甲苯 /邻二氯苯 (摩尔比 ) =1∶ 0 .6,w (偶氮二异丁腈 ) =0 .6% ,反应时间 3 h,反应温度 1 60℃ ,产物单程收率大于 65 % ;将反应混合物中未反应的原料分离后 ,以无水乙醇为溶剂结晶纯化 ,物料 /溶剂 (摩尔比 ) =1∶ 1 .5时晶体含量在 99.0 %以上 ,结晶收率达 67     

医用聚氯乙烯材料的表面光接枝改性

研究了在不排氧氛围下 ,紫外光照射 ,以二苯甲酮 (BP)为光引发剂 ,甲基丙烯酸缩水甘油酯(GMA)在医用聚氯乙烯 (PVC)薄膜表面的气相接枝聚合。探讨了反应条件对接枝结果的影响 ,并用正交法指出了影响因素的显著性。用傅立叶红外 (FT- IR)、水接触角作为接枝改性结果的表征。FT- IR谱图表明 GMA已接枝到 PVC膜表面。水接触角由接枝前的 78°下降到 5 4°     

十二酰胺丙基二甲基羟乙基氯化铵与十二烷基硫酸钠水溶液的表面吸附和胶束形成

利用十二酰胺丙基二甲胺和氯乙醇反应 ,合成了十二酰胺丙基二甲基羟乙基氯化铵 (DDHA)阳离子表面活性剂 ,将其与十二烷基硫酸钠 (SDS)以不同摩尔比进行混合 ,测定了混合系统的表面张力 ,计算了单一系统和混合系统的饱和吸附量、分子最小截面积 ,表面层和胶束中 DDHA的摩尔分率及分子间相互作用参数 ,目视观察了混合系统的浑浊情况。结果表明 :在降低γcmc和 cmc方面 ,DDHA SDS混合系统有协同效应 ,表面层和胶束的组成与二组分配比有关 ,但是非对称的 ,等物质的量混合物中 ,DDHA在胶束和表面层中具有较大的摩尔分数。DDHA与 SDS在实验测定的各混合系统中都不出现混浊     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

Immobilization and activation of vanadium(III) and titanium(III) single‐site catalysts for ethylene polymerization using MgCl2‐based supports

Significant increases in the activity of vanadium(III) amidinate catalysts for ethylene polymerization have been obtained by immobilization on a MgCl₂‐based support prepared by reaction of AlEt₃ with a MgCl₂/ethanol adduct. Catalyst immobilization and activation on this type of support prevents the rapid decay in activity observed under homogeneous polymerization conditions with unsupported catalysts. Stable polymerization activity is also observed with analogous titanium(III) complexes. Polyethylene with narrow molecular weight distribution and spherical particle morphology is obtained without reactor fouling. Copyright © 2005 Society of Chemical Industry     

Improvement of the deflocculating power of polyacrylates in ceramic slips by small additions of quaternary ammonium salts

In this work, we examine the effect of small additions of cationic quaternary ammonium salts (QAS) of different molecular weight on the rheology of an industrial ceramic suspension deflocculated with sodium polyacrylate and sodium metasilicate. The observed shear thinning behaviors obey the typical power law of fluid rheology. In order to characterize the rheological behavior of these slurries, three new parameters are introduced: a low shear rate consistency index and two transient viscosities, distant from the equilibrium, after increasing and decreasing the shear rates. These parameters vary with polyacrylate molecular weight and on additions of small quantities of QAS, which we found to be useful for decreasing the slurry viscosity.     

氯化铁催化合成富马酸二甲酯

氯化铁可代替硫酸催化酯化反应，探讨了氯化铁催化合成富马酸二甲酯的条件，操作简便，反应温和，无腐蚀，减少了污染与产品纯化。     

KCl与NaCl在低盐固态法酱油发酵中的应用比较

对KCl与NaCl在低盐固态酱油发酵中的应用进行了比较研究。结果表明：用KCl代替NaCl，KCl的浓度要高于NaCl才能抑制发酵期间杂茵的污染，且使用KCl的发酵效果比NaCl要好。     

Validation of a Method of Determination of Apparent Diffusivity Versus Composition in Solids

A method is presented for computing the values of apparent diffusivity in solids with respect to the concentration of the diffusing substance (water or sodium chloride). This method does not require any assumption upon the mathematical relationship between diffusivity and concentration. It can be applied to experimental measurements of local concentration versus position within the solid (profiles) with relatively few measurements (circa 10) and a mathematical smoothing of the experimental data by using an artificial neural network model. The method was first validated on simulated data obtained by using a constant diffusivity value and on experimental profiles when the relation between diffusivity and concentration was given. It was then applied to original experimental moisture profiles obtained by putting gelatin gels with different initial moisture contents into contact for up to 14 days. The method was also successfully applied to five sets of experimental moisture and sodium chloride profiles taken from the literature and obtained from different food products. Apparent diffusivities calculated by our method were found in agreement with those obtained by authors using different numerical methods to compute the diffusivity values.