Impact behavior and fractographic study of carbon nanotubes grafted carbon fiber-reinforced epoxy matrix multi-scale hybrid composites

Carbon nanotubes are the most promising reinforcement for high performance composites. Multiwall carbon nanotubes were directly grown onto the carbon fiber surface by catalytic thermal chemical vapor deposition technique. Multi-scale hybrid composites were fabricated using the carbon nanotubes grown fibers with epoxy matrix. Morphology of the grown carbon nanotubes was investigated using field emission scanning electron microscopy and transmission electron microscopy. The fabricated composites were subjected to impact tests which showed 48.7% and 42.2% higher energy absorption in Charpy and Izod impact tests respectively. Fractographic analysis of the impact tested specimens revealed the presence of carbon nanotubes both at the fiber surface and within the matrix which explained the reason for improved energy absorption capability of these composites. Carbon nanotubes presence at various cracks formed during loading provided a direct evidence of micro crack bridging. Thus the enhanced fracture strength of these composites is attributed to stronger fiber–matrix interfacial bonding and simultaneous matrix strengthening due to the grown carbon nanotubes.     

纤维在沥青混合料中的应用研究

选用工程中常用的几种纤维,结合工程应用要求,试验分析了纤维的吸湿性、耐热性,并通过网篮析漏试验、动态剪切试验和沉锥试验,讨论了纤维对沥青的稳定和吸附作用,以及纤维对沥青混合料“加筋”效果和作用机理。研究表明有的纤维“吸附、稳定”性能好,而有的纤维“加筋、桥接”效果好,在应用纤维时,应根据纤维的主要特点以及沥青混合料的使用要求来选用。     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.     

燃煤电厂融合多信号光纤火焰检测器的开发研究

介绍一种新型光纤燃煤炉火焰检测器，阐述其系统组成及特点，并提出了基于模糊推理的多信号融合处理方法。     

Holographic polymer‐dispersed liquid crystal fabrication under electric field

The transmission mode of holographic polymer‐dispersed liquid crystals (HPDLCs) was developed an under electric field. It is reported that orientation of LC molecules under an electric field induces orientation of oligomer molecules giving rise to low off‐state diffraction and small grating shrinkage. Copyright © 2005 Society of Chemical Industry     

Experimental Investigation of FRP-Strengthened RC Beam-Column Joints

The results of a comprehensive experimental program, aimed at providing a fundamental understanding of the behavior of shear-critical exterior reinforced concrete (RC) joints strengthened with fiber reinforced polymers (FRP) under simulated seismic load, are presented in this study. The role of various parameters on the effectiveness of FRP is examined through 2/3-scale testing of 18 exterior RC joints. Conclusions are drawn on the basis of certain load versus imposed displacement response characteristics, comprising the strength (maximum lateral load), the stiffness, and the cumulative energy dissipation capacity. The results demonstrate the important role of mechanical anchorages in limiting premature debonding, and they provide important information on the role of various parameters, including: area fraction of FRP; distribution of FRP between the beam and the column; column axial load; internal joint (steel) reinforcement; initial damage; carbon versus glass fibers; sheets versus strips; and effect of transverse beams.     

Deflection Calculation of FRP Reinforced Concrete Beams Based on Modifications to the Existing Branson Equation

Fundamental concepts of tension stiffening are used to explain why Branson’s equation for the effective moment of inertia Ie does not predict deflection well for fiber reinforced polymer (FRP) reinforced concrete beams. The tension stiffening component in Branson’s equation is shown to depend on the ratio of gross-to-cracked moment of inertia (Ig/Icr), and gives too much tension stiffening for beams with an Ig/Icr ratio greater than 3. FRP beams typically have an Ig/Icr ratio greater than 5, leading to a much stiffer response and underprediction of computed deflections as observed by others in the past. One common approach to computing deflection of FRP reinforced concrete beams has been to use a modified form of the Branson equation. This paper presents a rational development of appropriate modification factors needed to reduce the tension stiffening component in Branson’s original expression to realistic levels. Computed deflections using this approach give reasonable results with the right modification factor, and compare well with a more general unified approach that incorporates a realistic tension stiffening model. Comparison is made with the existing and past correction factors recommended by ACI 440 for predicting deflection of FRP beams. The method presently used by ACI 440 gives reasonable estimates of deflection for glass and carbon FRP reinforced beams. However, this method underestimates deflection of aramid FRP reinforced beams and is restricted to rectangular sections. A proposal is made for adoption of a simple modification factor that works well for all types of FRP bar and beam cross-sectional shape.     

Proposed Design of a CFRP Flange-to-Flange Connection for Precast Prestressed Double Tee Systems

The current methods of connecting the flanges of precast double tee members, and their respective short comings in specific situations, are described. A new carbon fiber-reinforced polymer (CFRP) flange-to-flange connection is proposed to eliminate the problems associated with repair requirements for the current connections. Design expressions for the currently used mechanical anchorage and the proposed CFRP connection are presented. A comparative calculation for the two systems is given.     

Nucleation of copper on an assembly of carbon microelectrodes

The initial stage of copper electrodeposition on the electrochemically activated assembly of carbon microelectrodes from an acid solution of copper sulfate was investigated using cyclic voltammetry, potentiostatic pulse technique and electrochemical impedance spectroscopy. Analysis of the experimental current transients has been carried out using a non-linear fitting procedure according to the model that takes into account spherical diffusion towards a disc-shaped microelectrode. The higher values of diffusion coefficient in comparison with those observed on planar electrodes were explained with an increased diffusion caused by the electrode geometry. Impedance spectra showed two time constants, the high-frequency related to the charge transfer process and the low-frequency corresponded to the deposit morphology.     

A Family of Far‐Infrared‐Transmitting Glasses in the Ga–Ge–Te System for Space Applications

Conditions of formation of bulk tellurium chalcogenide glasses, containing 70–80 at % Te associated to Ga and Ge are described. The characteristic temperatures are measured: the glass‐transition temperature, T_g, is situated in the range 140–185 °C and the difference T_x – T_g, where T_x is the onset crystallization temperature, is in the range 76–113 °C. Moreover, the optical transmission window is exceptional, ranging from 1.99 μm in the bandgap up to 28 μm in the phonon region. Developed within the framework of requirements for the Darwin mission (a search for and study of extrasolar planets), feasibility of infrared optical fibers formed from these glasses is studied. Drawing experiments are conducted with the glass Ga₂‐Ge₃Te₁₅, which possesses the maximum T_x – T_g, and a first optical fiber is presented.