A continuum-based modeling of MEMS devices for estimating their resonant frequencies

A continuum-based modeling of coupled electrostatics-structure interactions is presented for the frequency computations of MEMS devices. The present general formulation of electrostatics accounting for free space is validated first by specializing it to one-dimensional uniform motion of conducting surfaces and comparing the resulting electrostatics to conventional lumped models. The general coupled electrostatics-structure interactions are then applied for the prediction of resonant frequencies of MEMS devices due to bias-voltage changes and temperature variations. Comparisons of predicted resonant frequencies obtained by the present coupled electrostatics-structure interaction models with experimental results available in the literature demonstrate that the proposed continuum-based interaction modeling yields high-confidence predictions of resonant frequencies of MEMS devices.     

Holographic polymer‐dispersed liquid crystal fabrication under electric field

The transmission mode of holographic polymer‐dispersed liquid crystals (HPDLCs) was developed an under electric field. It is reported that orientation of LC molecules under an electric field induces orientation of oligomer molecules giving rise to low off‐state diffraction and small grating shrinkage. Copyright © 2005 Society of Chemical Industry     

Probabilistic analysis of a static frame model

This paper describes our efforts during our participation in the Sandia Validation Workshop. The focus of the paper is the calibration of material models and simulation of random fields to characterize the variations of material properties across spatial field. Both parametric and non-parametric methods were used to represent uncertainty. Part of the challenge of this problem is the small amount of data that is available for the necessary probabilistic analyses in support of calibration, validation, accreditation and prediction activities. The analysis methods and corresponding results are described.     

Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Effect of electric field on the hydrodynamics of fluidized nanoparticles

The effect of electric field on the hydrodynamics of nanoparticles was studied in a fluidized rectangular bed, with electrodes attached to two parallel walls. It was shown that the electric field of the order of 3 times the gravity markedly decreased the bed expansion and increased the solids volume fraction of nanoparticles fluidized by air. In these experiments, a light diode assembly was utilized to infer the local solids volume fractions within a rectangular bed of 10 nm silica particles. These experimental measurements yielded a two dimensional solids volume fraction distribution within the rectangular bed. The experimental results provided some new insights into the distribution of solids within the bed. The agglomerate diameters were computed using a momentum balance with the drag given by the Ergun equation and the empirical Richardson-Zaki method. Both methods yielded agglomerate diameters of the order of 100 μm and showed dependence on the strength of the electric field. The electric field decreased the granular temperature of the nanoparticles.     

Structural and Superconducting Property Variations with Nominal Mg Non‐Stoichiometry in MgxB2 and Its Enhancement of Upper Critical Field

By applying a combination of characterisation tools, changes in structural and superconducting properties with nominal Mg non‐stoichiometry in Mg_xB₂ are found. The non‐stoichiometry produces enhanced in‐field critical current densities (J_c's) and upper critical field / irreversibility field (H_c2/H_irr(T)) values. Upper critical fields of ～ 21 T (4.2 K) were obtained in nominal Mg‐deficient samples compared to ～ 17 T (4.2 K) for near‐stoichiometric samples.     

An analysis of shielding against DC magnetic fields generated by electric railways. Evaluation of effective permeability of fine structure

This paper describes an effective analysis of magnetic shielding based on homogenization. The analyses become time‐consuming if the problems include the magnetic substances having fine structure. The homogenization of the structure makes it possible to analyze effectively the magnetic fields. The authors introduce a method to estimate the effective permeability of the homogenized substance. This method can be applied to any periodic structure made of magnetic substance. The magnetic shielding effects by the structures against direct‐current (DC) fields generated by electric railways are analyzed by using the present method. As a result, it is found that the overhead way and the protective fence near the railway work as a magnetic shield, whose effects can be improved by appropriate arrangement of those constructions. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 160(4): 7–15, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20310     

Analysis of brushless three-phase synchronous generator without exciter

Recently, a demand for small-capacity generators has been increasing as electric sources in small ships and automobiles or as portable electric sources driven by engines. It is desired that the structure of small-capacity generators be simple and robust, and that the generators be highly reliable, easily maintained and controlled. This paper describes an analysis of the original brushless synchronous generator without exciter. The output voltage can be adjusted in the wide range by controlling the stator dc current. To analyze the characteristics of this generator, the finite element method is applied. It is found that the results of theoretical analysis agree well with the experimental results.     

Performance prediction of a hybrid‐excitation synchronous machine with axially arranged excitation poles and permanent‐magnet poles

This paper presents a method of predicting the steady‐state performance of a new hybrid‐excitation synchronous machine (HESM) theoretically. The field pole of this HESM is axially divided into two parts; one is an excitation part and the other a permanent‐magnet (PM) part. A nonlinear equivalent circuit, which can include the saliency of the rotor and the magnetic saturation due to the iron core, is derived. Based on this equivalent circuit, the steady‐state performance of the HESM is calculated, and the results are confirmed through experiments. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(2): 43–49, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20033