Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

JETS,PLUMES AND BUOYANT JETS IN STATIC ENVIRONMENT

Turbulence represents an essential aspect in atmospheric and oceanic circulations.In particu-lar,it is a preponderant factor in the dispersion of pollutants of artificial or natural origin.Thevertical turbulent jets,plumes and buoyant jets discharging into static environment is one of themost important and basic flow patterns related with the environment pollution.These flows havenumerous important applications,for example,thrust augmentors,waste disposal plumes fromstacks and combustion systems,and significant problems of turbulent diffusion.     

ETR Ⅱ-30调速器液压控制系统

ETRⅠ-30调速器是瑞士爱舍维斯工厂生产的具有PID调节规律的电液调速器。本文对其液压控制系统作了较详细的介绍,供有关人员参考。     

建(构)筑物机械拆除方法综述

介绍了几种常用的建(构)筑物机械拆除方法,对其工作原理、特点、应用条件及局限性加以分析和说明。     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

钨铜合金药型罩及其性能

钨铜合金药型罩的应用可以提高射流对均质钢靶的侵彻能力.这一提高得益于射流密度的提高以及断裂时间的延长. 本文对钨铜合金射流及其断裂形态通过X光照像进行了研究.它的旋转效应及其炸高特性也进行了实验研究. 钨铜合金药型罩的威力实验在φ30 mm的破甲弹上进行.在相同装药条件下与紫铜罩相比,威力提高20～30%.     

SISAK快速化学分离装置的建立

SISAK(Short-lived Isotopes Studies by the AKUFVE technique)技术是目前使用最广泛的快速化学分离方法之一,主要应用在短寿命核素的分离和鉴别、超重元素的人工合成以及化学性质研究等方面的工作中.本文简单地叙述了SISAK技术的流程、原理和发展现状,介绍了自行建立的国内第一套基于SISAK技术的快速化学分离装置,并通过从裂变产物中分离短寿命核素这一实例验证了SISAK技术在快速化学分离中的优越性.     

热流体喷射变形机理与喷嘴结构

高速短程纺技术能生产三维卷曲短纤维,该技术的关键之一是热流体喷射装置。本文介绍了热流体喷射装置的演变与特点及它的加工机理和某些已应用的实际装置。