A hybrid homogeneously weighted moving average control chart for process monitoring: Discussion

The sensitivity of a monitoring scheme depends on many factors including the variance of the charting statistic which is very important in the computation of the control limits. This paper discusses the computation of the variance of the recently proposed hybrid homogeneously weighted moving average (HHWMA) $\overline{X}$ scheme which was based on an incorrect assumption. The correct variance is used to evaluate the run-length characteristics of the HHWMA $\overline{X}$ scheme. It is observed that the incorrect variance has a significant impact on the sensitivity (or performance) of the HHWMA $\overline{X}$ scheme.     

Effect of strain rate on the dynamic compressive mechanical behaviors of rock material subjected to high temperatures

Strain rate is not only an important measure to characterize the deformation property, but also an important parameter to analyze the dynamic mechanical properties of rock materials. In this paper, by using the SHPB test system improved with high temperature device, the dynamic compressive tests of sandstone at seven temperatures in the range of room temperature to 1000 °C and five impact velocities in the range of 11.0–15.0 m/s were conducted. Investigations were carried out on the influences of strain rate on dynamic compressive mechanical behaviors of sandstone. The results of the study indicate that the enhancement effects of strain rates on dynamic compressive strength, peak strain, energy absorption ratio of sandstone under high temperatures still exist. However, the increase ratios of dynamic compressive strength, peak strain, and energy absorption ratio of rock under high temperature compared to room temperature have no obvious strain rate effects. The temperatures at which the strain rates affect dynamic compressive strength and peak strain most, are 800, and 1000 °C, respectively. The temperatures at which the strain rates affect dynamic compressive strength and peak strain weakest, are 1000 °C, and room temperature, respectively. At 200 and 800 °C, the strain rate effect on energy absorption ratio are most significant, while at 1000 °C, it is weakest. There are no obvious strain rate effects on elastic modulus and increase ratio of elastic modulus under high temperatures. According to test results, the relationship formula of strain rate with high temperature and impact load was derived by internalizing fitting parameters. Compared with the strain rate effect at room temperature condition, essential differences have occurred in the strain rate effect of rock material under the influence of high temperature.     

Electroactive polymers containing 3-arylcarbazolyl units as hole transporting materials for OLEDs

Monomers and their polymers containing 3-arylcarbazolyl electrophores have been synthesized by the multi-step synthetic route. The materials were characterized by thermo-gravimetric analysis, differential scanning calorimetry and electron photoemission technique. The polymers represent materials of high thermal stability having initial thermal degradation temperatures in the range of 331–411 °C. The glass transition temperatures of the amorphous polymeric materials were in the rage of 148–175 °C. The electron photoemission spectra of thin layers of monomers showed ionization potentials in the range of 5.6–5.65 eV. Hole-transporting properties of the polymers were tested in the structures of organic light emitting diodes with Alq₃ as the green emitter. The device containing hole-transporting layers of polyether with 3-naphthylcarbazolyl groups exhibited the best overall performance with a maximum current efficiency of 3.3 cd/A and maximum brightness of about 1000 cd/m².     

燃煤锅炉除尘专用滤料的开发

介绍机械制造厂燃煤锅炉的烟尘特点,分析滤料失效的原因,提出一套针对该工况的滤料解决方案。介绍针对复杂工况条件所选用的纤维种类以及复合面层原料成分配比的确定,最终选用针刺工艺加工并对该新产品的基本性能进行了测试分析。     

The World robot summit disaster robotics category – achievements of the 2018 preliminary competition

The World Robot Summit is a robot Olympics and aims to be held in a different country every four years from 2020. The concept of the Plant Disaster Prevention challenge is daily inspections, checks, and emergency response in industrial plants, and in this competition, robots must carry out these types of missions in a mock-up plant. The concept of the Tunnel Disaster Response and Recovery challenge is emergency response to tunnel disasters, and is a simulation competition whereby teams compete to show their ability to deal with disasters, by collecting information and removing debris. The Standard Disaster Robotics challenge assesses, in the form of a contest, the standard performance levels of a robot that are necessary for disaster prevention and emergency response. The World Robot Summit Preliminary Competition was held at Tokyo Big Sight in October 2018, and 36 teams participated in the Disaster Robotics Category. UGVs and UAVs contended the merits of new technology for solving complex problems, using core technologies such as mobility, sensing, recognition, performing operations, human interface, autonomous intelligence etc., as well as system integration and implementation of strategies for completing missions, gaining high-level results.     

无源光网络标准发展及关键技术研究

无源光网络(Passive Optical Network,PON)作为当今接入网的主要技术解决方案,具有带宽使用效率高、传输距离远、抗干扰能力强等特点.通过研究PON技术的发展动态,本文首先归纳了各种PON技术的产生背景和应用特点,整理出各技术间的连接关系及主要标准;其次介绍了PON技术的帧结构,并对带宽、波长、传输模式等PON技术的主要参数进行了汇总;然后将国内外研究热点进行划分,围绕媒体访问控制协议、帧结构、动态带宽分配算法、节能机制等关键技术,阐述了其研究现状及在PON中的重要作用;最后对PON技术的发展趋势进行了展望.     

测井资料在优选压裂层位中的应用

压裂是低孔、低渗油层改造的主要增产措施。根据常规测井资料、岩石物理实验分析数据及试油成果。研究储层四性关系，确定区块的低孔、低渗储层评价标准。进一步对油层进行分类，有针对性地为油层压裂提供施工层位和准确的储层参数。通过商543区块实例，阐述了选择压裂层位的方法。     

Methods of Verifying Continuous Automatic Belt Weighers: State and Prospects

The basic methods of verifying continuous automatic belt weighers are described. A comparative analysis of these methods on the basis of experimental studies is made and ways of implementing the results in industry are recommended.     

Mathematical modelling and numerical simulation of ordered porosity metal materials formation

Ordered porosity metal materials belong to a relatively new class of porous materials named gasars. This paper presents a mathematical model of the complex physical phenomena in the production of gasars. Analyses for heat transfer, solidification kinetics and gas diffusion were coupled to describe the formation of unique gasar structure. Several criterial functions were introduced to provide significant quantitative information about the relationship between the operating technological parameters and the final structure. The computational outcomes of the numerical simulation were compared with the characteristics of real gasar ingots. The model was applied to determine the boundary conditions that would provide approximately constant physical conditions on the solidification front. The structure sensitiveness of gasars with respect to the different technological parameters is discussed.