蛋类礼盒包装结构的缓冲性能研究

目的研究蛋类礼盒包装结构的缓冲性能。方法以蛋类尺寸为基础,建立可发性聚乙烯(expandable polyethylene. EPE)缓冲单元结构和组合结构,进行静态仿真分析和实验验证,比较结构在形状、叠合层数、组合形式等参数变化时的载荷与位移。结果结构层数变化相同时,单元结构的极限载荷从143N增加到236 N,组合结构的极限载荷从224 N增加到476 N,均呈近线性增长。结论蛋类礼盒包装中,组合结构的承载能力优于单元结构,通过单元结构的组合,可满足不同蛋类的包装要求。     

Experimental study on the heat transfer and flow characteristics of nanorefrigerants inside a corrugated tube

The heat transfer and flow characteristics of MWCNT-R141b nanorefrigerant with different mass fractions have been studied through experiments. Experimental results were compared with existing correlations. A two-step method was used to prepare the nanorefrigerants. Span-80 was used as surfactant with an average particle diameter of 20 nm. Transmittance method was used to evaluate the stability of nanorefrigerants. Results showed that the stability of MWCNT-R141b nanorefrigerant, which is the added dispersant, was good during the experiments. The 0.3 wt% MWCNT-R141b nanorefrigerants had optimal heat transfer enhancement effects compared with pure refrigerants. The maximum Nusselt number increased by 40%. The specific pressure drop of nanorefrigerant increased as the Reynolds number (Re) increased, and the specific pressure drop of the pure refrigerant was minimum, which is similar to R141b.     

Effect of strain rate on the dynamic compressive mechanical behaviors of rock material subjected to high temperatures

Strain rate is not only an important measure to characterize the deformation property, but also an important parameter to analyze the dynamic mechanical properties of rock materials. In this paper, by using the SHPB test system improved with high temperature device, the dynamic compressive tests of sandstone at seven temperatures in the range of room temperature to 1000 °C and five impact velocities in the range of 11.0–15.0 m/s were conducted. Investigations were carried out on the influences of strain rate on dynamic compressive mechanical behaviors of sandstone. The results of the study indicate that the enhancement effects of strain rates on dynamic compressive strength, peak strain, energy absorption ratio of sandstone under high temperatures still exist. However, the increase ratios of dynamic compressive strength, peak strain, and energy absorption ratio of rock under high temperature compared to room temperature have no obvious strain rate effects. The temperatures at which the strain rates affect dynamic compressive strength and peak strain most, are 800, and 1000 °C, respectively. The temperatures at which the strain rates affect dynamic compressive strength and peak strain weakest, are 1000 °C, and room temperature, respectively. At 200 and 800 °C, the strain rate effect on energy absorption ratio are most significant, while at 1000 °C, it is weakest. There are no obvious strain rate effects on elastic modulus and increase ratio of elastic modulus under high temperatures. According to test results, the relationship formula of strain rate with high temperature and impact load was derived by internalizing fitting parameters. Compared with the strain rate effect at room temperature condition, essential differences have occurred in the strain rate effect of rock material under the influence of high temperature.     

Friction compensation controller for load varying machine tool feed drive

The load applied to a machine tool feed drive changes during the machining process as material is removed. This load change alters the Coulomb friction of the feed drive. Because Coulomb friction accounts for a large part of the total friction the friction compensation control accuracy of the feed drives is limited if this nonlinear change in the applied load is not considered. This paper presents a new friction compensation method that estimates the machine tool load in real time and considers its effect on friction characteristics. A friction observer based on a Kalman filter with load estimation is proposed for friction compensation control considering the applied load change. A specially designed feed drive testbed that enables the applied load to be modified easily was constructed for experimental verification. Control performance and friction estimation accuracy are demonstrated experimentally using the testbed.     

Theoretical study of a thermoelectric-assisted vapor compression cycle for air-source heat pump applications

This paper proposes a thermoelectric-assisted vapor compression cycle (TVCC) for applications in air-source heat pump systems which could enhance the heating capacity of the system. Performances of TVCC are calculated and then compared with that of basic vapor compression cycle (BVCC). The simulation results show that when coefficients of performance (COPs) of the two cycles are almost equal, the TVCC under maximum COP condition of the thermoelectric modules still performs better than BVCC by 13.0% in heating capacity through selecting the appropriate intermediate temperature. In addition, the TVCC can also achieve an improvement of 16.4%–21.7% in both the heating COP and capacity when compared with the BVCC with an assistant electric heater that is provided with the equivalent power input of thermoelectric heat exchanger. Thus, the TVCC could be beneficial to the applications in small heat pumps if there is always need for auxiliary electric heat.     

Producing fully-lamellar microstructure for wrought beta-gamma TiAl alloys without single α-phase field

Fine-grained fully-lamellar (FL) microstructure is desired for TiAl components to serve as compressor/turbine blades and turbocharger turbine wheels. This study deals with the process and phase transformation to produce FL microstructure for Mo stabilized beta-gamma TiAl alloys without single α-phase field. Unlike the α + γ two-phased TiAl or beta-gamma TiAl with single α-phase field, the wrought multi-phase TiAl–4/6Nb–2Mo–B/Y alloys exhibit special annealing process to obtain FL microstructure. Short-term annealing at temperatures slightly above β-transus is recommended to produce the desired FL microstructure. The related mechanism is to guarantee the sufficient diffusion homogenization of β stabilizers during single β-phase annealing, and further avoid α decomposition by α → γ + β when cooling through α + β + γ phase field. The colony boundary β phase contributes to fine-grained nearly FL microstructure, by retarding the coarsening of the α phase grains.     

Assessment of spray quality from an external mix nozzle and its impact on SQL grinding performance

Spray quality is the critical factor which decides the efficacy of Small Quantity Lubrication (SQL) technology in a high specific energy involved machining process like grinding. Yet, the understanding about spray quality, the actual process mechanics and its effect on machining performance is inadequate. The present work is an attempt to establish a correlation between the spray input variables, quality of the spray and machining performance of SQL grinding through modelling and experiments. Using computational fluid dynamic techniques, the variation of droplet size, droplet velocity, number of droplets and heat transfer coefficient have been analysed at different input parameters and the computed trends have been verified and validated. CFD modelling of spray indicates that it is possible to produce aerosol medium with high heat dissipation ability at moderately high air pressure and low flow rate. It also shows that any increase in atomising air pressure favourably leads to notable increase in wetting area and also results in substantial enhancement in heat dissipation ability. Reduction of residual stress is thus remarkably good. On the other hand, grinding fluid flow rate, if increased, offers significantly better lubricity and reduces the grinding force which also reduces tensile residual stress. Short spell grinding test results are found to be in good agreement with CFD results.     

异构分层无线网络中基于逗留时间的动态流量均衡算法研究

为使异构分层无线网络能服务更多的移动用户,提出了一种基于逗留时间的动态流量均衡算法.该算法首先根据用户移动模型计算其在小区内的逗留时间,然后基于小区呼叫到达率和重叠覆盖小区的流量状态来确定一个周期内呼叫转移的数量,最后依据逗留时间门限值将重负载小区中满足条件的呼叫转移到轻负载的重叠覆盖小区中.为降低切换呼叫掉线率,还对异构网间的呼叫切换策略做了改进.仿真实验结果表明,本算法在新呼叫阻塞率和切换呼叫掉线率等性能指标上比传统方法有显著的提高.     

对CFG桩质量缺陷的探讨

根据具体工程的概况及水文地质条件，分析了CFG桩在地下水位出现大面积缩颈现象和复合地基载荷试验达不到设计要求的原因，并介绍了地基补强措施，以满足工程质量的要求。     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.