Enhanced gaseous hydrogen solubility in ferritic and martensitic steels at low temperatures

Metals that are exposed to high pressure hydrogen gas may undergo detrimental failure by embrittlement. Understanding the mechanisms and driving forces of hydrogen absorption on the surface of metals is crucial for avoiding hydrogen embrittlement. In this study, the effect of stress-enhanced gaseous hydrogen uptake in bulk metals is investigated in detail. For that purpose, a generalized form of Sievert's law is derived from thermodynamic potentials considering the effect of microstructural trapping sites and multiaxial stresses. This new equation is parametrized and verified using experimental data for carbon steels, which were charged under gaseous hydrogen atmosphere at pressures up to 1000 bar. The role of microstructural trapping sites on the parameter identification is critically discussed. Finally, the parametrized equation is applied to calculate the stress-enhanced hydrogen solubility of thin-walled pipelines and thick-walled pressure vessels during service.     

The influence of carbon atom distribution in precursors with 1:1 carbon to silicon atoms ratio on structure and thermal evolution of obtained silicon oxycarbide based materials

In this work, a number of precursors with 1:1 silicon to carbon atoms ratio and various carbon atom distributions were synthesized and pyrolyzed in order to obtain silicon oxycarbide based materials. The different carbon atom distributions were obtained using both simple monomers with only one silicon atom, as well as large monomers containing either four or sixteen silicon atoms with predefined carbon atom positions. The silicon oxycarbide based materials were investigated using IR, XRD, ²⁹Si MAS NMR and elemental analysis after annealing at various temperatures, as well as TG. The research shows that carbon atom distribution has great impact on the structure of final material and can be used to tailor the material for its projected uses.     

Feedforward control of the transverse strip profile in hot-dip galvanizing lines

Hot-dip galvanizing is a standard technology to produce coated steel strips. The primary objective of the galvanizing process is to establish a homogeneous zinc layer with a defined thickness. One condition to achieve this objective is a uniform transverse distance between the strip and the gas wiping dies, which blow off excessive liquid zinc. Therefore, a flat strip profile at the gas wiping dies is required. However, strips processed in such plants often exhibit residual curvatures which entail unknown flatness defects of the strip. Such flatness defects cause non-uniform air gaps and hence an inhomogeneous zinc coating thickness. Modern hot-dip galvanizing lines often use electromagnets to control the transverse strip profile near the gas wiping dies. Typically, the control algorithms ensure a flat strip profile at the electromagnets because the sensors for the transverse strip displacement are also located at this position and it is unfeasible to mount displacement sensors directly at the gas wiping dies. This brings along that in general a flatness defect remains at the gas wiping dies, which in turn entails a suboptimal coating.In this paper, a model-based method for a feedforward control of the strip profile at the position of the gas wiping dies is developed. This method is based on a plate model of the axially moving strip that takes into account the flatness defects in the strip. First, an estimator of the flatness defects is developed and validated for various test strips and settings of the plant. Using the validated mathematical model, a simulation study is performed to compare the state-of-the-art control approach (flat strip profile at the electromagnets) with the optimization-based feedforward controller (flat strip profile at the gas wiping dies) proposed in this paper. Moreover, the influence of the distance between the gas wiping dies and the electromagnets is investigated in detail.     

Fretting-induced friction and wear in large flat-on-flat contact with quenched and tempered steel

Fretting may cause severe surface damage and lead to unexpected fatigue failure. Our test apparatus was designed based on reciprocating, large, annular flat-on-flat contact without any edge effects in the direction of the fretting movement. Fretting wear tests were run with quenched and tempered steel with different normal pressures and sliding amplitudes under gross sliding conditions. The development of the friction coefficient and total wear mass depended mostly on the accumulated sliding distance. Initially, friction and wear were highly adhesive but gradually changed to abrasive due to third body accumulation in the interface.     

高精度薄壁钢套类零件制造工艺

薄壁钢套类零件是机械制造中常碰到的一类难加工零件,由于其不同的功能用途和典型结构特点,其制造有一定难度,在实际生产过程中,经常出现加工制造后的零件尺寸精度、形状精度、形位精度达不到使用及设计要求。本文较系统地阐述了薄壁钢套类零件的典型制造工艺方法以及在制造过程中的变形分析和应对措施。     

Modelling dislocation assisted tempering during rolling contact fatigue in bearing steels

Rolling contact fatigue in bearing steels is manifested by dark-etching regions, which are attributed to deformation induced tempering. In order to quantitatively explain this phenomenon, a model is suggested for martensite tempering assisted by dislocation glide during rolling contact fatigue. In the model, dislocations transport carbon from the matrix to carbide particles, provided that the carbon is located at a certain distance range from the dislocation contributing to the tempering process. By calculating the amount of carbon in the matrix, the kinetics of carbide thickening and hardness reduction are computed. It is found that the dark-etching region kinetics can be controlled by both bearing operation conditions (temperature and deformation rate) and microstructure (type, size, and volume fraction of carbides). The model is validated against tested bearings, and its limitations are discussed.     

毒品滥用流行病模型的稳定性分析

现有毒品滥用流行病模型假设吸毒者康复后对毒品拥有永久"免疫"力，而忽视了其再次成为毒品易感者的可能性。针对这一问题，通过考虑社区治疗和隔离治疗两种措施，分析了毒品滥用人群的演化过程，提出了基于暂时"免疫"力的毒品滥用流行病模型，并计算了模型的基本再生数，讨论了模型平衡点的存在性和稳定性。当基本再生数小于1时，模型存在一个局部渐进稳定的无毒平衡点；当基本再生数大于1时，模型存在唯一的地方病平衡点，并利用几何方法证明了地方病平衡点的全局稳定性；当基本再生数等于1时，如果满足一定条件，模型出现后向分支现象。数值模拟验证了上述所有结果。研究结果表明提高隔离治疗率、改善社区治疗效果和降低接触传染率可以有效抑制毒品滥用的流行。     

Effect of steel slag on 3D concrete printing of geopolymer with quaternary binders

A new type of 3D-printable ‘one-part’ geopolymer was synthesized with fly ash (FA), granulated blast furnace slag (GBFS), steel slag (SS) and flue gas desulfurization gypsum (FGD). The effects of SS content (0–40%) on the rheological properties, 3D-printability, mechanical anisotropy and reaction kinetics of geopolymer were investigated. The yield stress and plastic viscosity monotonically decreased with the increasing SS content. Contrarily, the geopolymer with 10% of SS presented better extrudability, buildability and mechanical strength than those with 0, 20%, 30% and 40% of SS. This was mainly attributed to the conflicting influence of SS on geopolymerization, of which the OH^? produced by hydration of SS raised the alkalinity of the reaction system and accelerated the dissolution of SiO₄^4? and AlO₄^5?, while the low reactivity prohibited the following polymerization process. Furthermore, the 3D-printed geopolymer presented more compact microstructure and less mechanical anisotropy thanks to the crosslinking of morphologically complementary products, including N(C)-A-S-H, C–S–H, AFt and CH, formed via synergistic reaction of FA-GBFS-SS-FGD system.     

Sex and Depot Differences in Palmitoleic Acid Content of Human Blood and Fat

Palmitoleic acid has been classified as an insulin-sensitizing lipokine, but evidence for this from human studies has been inconsistent. We hypothesized that this is related to either the types of samples or conditions under which samples are collected. We measured plasma palmitoleic acid and total free fatty acids (FFA) using ultra-performance liquid chromatography in blood samples collected from 34 adults under a variety of conditions. We collected duplicate samples of adipose (n = 10), FFA (n = 9), and very low density lipoprotein triacylglycerol (VLDL-TAG) (n = 7) to measure the palmitoleic acid as a percentage of total fatty acids. We tested whether the percentage of palmitoleic acid was correlated with insulin resistance, as measured by homeostatic model of insulin resistance (HOMA-IR). Adipose stearoyl-coenzyme A desaturase 1 (SCD-1) protein was measured by capillary Western blotting. FFA-palmitoleic acid percentage increased as a function of total FFA and was greater (p < 0.005) in females than males. Adipose palmitoleic acid percentage was greater in females than males (p < 0.001), as was adipose SCD-1. Palmitoleic acid was greater in femoral fat than in abdominal fat in both females and males (p < 0.001), and correlated positively with HOMA-IR only in females. The test–retest reliability values for percentage palmitoleic acid were 7 ± 10% for adipose, 24 ± 26% for VLDL, and 53 ± 31% for FFA. Because FFA-palmitoleic acid percentage varies as a function of total FFA, investigators should re-evaluate how palmitoleic acid data is presented. The positive relationship between adipose palmitoleic acid and HOMA-IR in females suggests that it is not a potent insulin-sensitizing lipokine in humans.     

Finite element analysis of femoral components paper III – hip joints

Finite element analysis of the hip implant is conducted in this paper for representative femoral cross-section geometries and development of stress in the presence of bone cement is elucidated. Differences in cement stresses generated by varying implant cross-sections were compared with conventional features derived from representative implants. The analysis was performed under idealized implant assemblies by constraining the implant movement in the assembly. The cross-sections and implant geometries used are generic and intended to be representative of available geometries. This paper is a part of student research projects, prepared from a series of activities in biomedical implant research currently underway at Ohio Northern and Arkansas Tech Universities.