Experimental study and model predictions on helium release in an enclosure with single or multiple vents

This paper presents experiments performed at Canadian Nuclear Laboratories (CNL) to examine the dispersion behaviour of helium in a polycarbonate enclosure that was representative of a residential parking garage. The purpose was to gain a better understanding of the effect of buoyancy- or wind-driven natural ventilation on hydrogen dispersion behaviour. Although hydrogen dispersion studies have been reported extensively in the literature, gaps still exist in predictive methods for hazard analysis. Helium, a simulant for hydrogen, was injected near the centre of the floor with a flow rate ranging from 5 to 75 standard litres per minute through an upward-facing nozzle, resulting in an injection Richardson number ranging between 10^?1 and 10². The location of the nozzle varied from the bottom of the enclosure to near the ceiling to examine the impact of the nozzle elevation on the development of a stratified layer in the upper region of the enclosure. When the injection nozzle was placed at a sufficiently low elevation, the vertical helium profile always consisted of a homogenous layer at the top overlaying a stratified layer at the bottom. To simulate outdoor environmental conditions, a fan was placed in front of each vent to examine the effect of opposing or assisting wind on the dispersion. The helium transients in the uniform layer predicted with analytical models were in good agreement with the measured transients for most tests. Model improvements are required for adequately predicting transients with primarily stratified profiles or strong opposing wind.     

控制爆破法处理卡钻事故

介绍了在包头市某工程实施管道穿越黄河施工中,采用爆破法处理卡钻的经验。针对深水环境条件及钻杆内径小不宜采用集团装药的条件,确定采用"小直径爆破筒,钻杆内部装药"的爆破方案,阐述了爆破设计及施工注意事项。可供类似工程参考。     

The short- and long-run efficiency of energy,precious metals,and base metals markets: Evidence from the exponential smooth transition autoregressive models

The aim of this paper is to investigate the long and short-run relationship between spot and futures prices of the energy, precious metals, and base metals markets. We analyze daily data from January 1985 to February 2019. The empirical findings based on the cointegration test, which follows a nonlinear process, suggest that the spot prices of energy and metals assets have long-run relationships with their futures prices. Nonparametric Granger causality test results also indicate bi-directional causality among futures and spot prices. These findings indicate that the energy and metals markets are informationally efficient in the sense of Fama (1970).     

基于残差决策的自动飞行控制系统远程实时故障诊断

针对自动飞行控制系统结构复杂、关联部件众多,发生故障时诊断时间长,从而影响飞机运行效率的问题,提出一种基于飞机通信寻址报告系统(ACARS)的远程实时故障诊断方案。首先,分析自动飞行控制系统的故障特点,设计搭建检测滤波器;然后,利用ACARS数据链实时发送的自动飞行控制系统的关键信息进行相关部件的残差计算,并根据残差决策算法进行故障诊断及定位;最后,针对不同故障部件残差间的差异大、决策门限无法统一的缺点,提出基于二次差值的残差决策改进算法,减缓了检测对象的整体变化趋势,降低了随机噪声和干扰的影响,避免了将瞬态故障诊断为系统故障的情况。实验仿真结果表明,基于二次差值的改进残差决策算法避免了多决策门限的复杂性,在采样时间为0.1 s的情况下,故障检测所需时间大约为2 s,故障检测时间大幅降低,有效故障检测率大于90%。     

A model- and simulation-based approach for tolerancing and verifying the functional capability of micro/nano-structured workpieces

The evaluation of functional features of manufactured workpieces is based on GO- and NO-GO-test results, which are obtained by comparing measured geometric characteristics with nominal dimensions and tolerances specified by the designer. These geometrical specifications are based on a tolerancing system, which was originally defined for the function mating capability. Against the background of upcoming lots of other new functions (like reduction of flow resistance, light absorption, reduction of friction, diffraction of light, self-cleaning or mass transmission) are to be realized with our products – particularly by micro- and nano scaled features. If the verification process will deliver the prediction of the achievable degree of functionality, the usability of a part can be assessed more accurately and in consequence quality and economics can be improved. So, a new principle for tolerancing and verifying turns out to be necessary. In this paper the fundamental deficit of the actual tolerancing and specification systems GPS and ASME Y14.5 is derived and the path for enlarging the system by preposing a functional model is shown. To verify the functional capability of the workpieces an approach based on simulations done with the parameterized mathematical–physical model of the function is suggested. Advantages of this approach will be discussed and demonstrated by examples with microstructured inking rolls, crankshafts and injection valves.     

Vertical cyclic loading response of geosynthetic-encased stone column in soft clay

Dynamic responses of the geosynthetic-encased stone column (GESC) supported embankment under traffic loads have become a hot topic. This study investigates the responses of GESC improved ground under vertical cyclic loading. A series of laboratory tests in a designed model test tank have been carried out with different loading parameters (varied loading amplitudes and frequencies), different column dimensions (varied encasement lengths and column diameters). In the tests, the soil-column stress distribution, accumulated settlement of loading plate, excess pore water pressure in the surrounding soil and lateral bulging of the stone column are monitored. Experimental results indicate that the vertical stress on the stone column increases with the increment of encasement length, and decreases with the increment of column diameter, loading amplitude and loading frequency. The increasing stress on the surrounding soil leads to a greater accumulated settlement of the loading plate and excess pore water pressure, while the increasing stress on the column leads to larger lateral bulging of the column. Excess pore water pressure dissipates effectively through vertical and horizontal drainage channels provided by the stone column and the sand bed. The geosynthetic encasement prevents the clay from obstructing the drainage channel by filtration and guarantees the drainage effect.     

TCBR-HMM: An HMM-based text classifier with a CBR system

This paper presents an innovative solution to model distributed adaptive systems in biomedical environments. We present an original TCBR-HMM (Text Case Based Reasoning-Hidden Markov Model) for biomedical text classification based on document content. The main goal is to propose a more effective classifier than current methods in this environment where the model needs to be adapted to new documents in an iterative learning frame. To demonstrate its achievement, we include a set of experiments, which have been performed on OSHUMED corpus. Our classifier is compared with Naive Bayes and SVM techniques, commonly used in text classification tasks. The results suggest that the TCBR-HMM Model is indeed more suitable for document classification. The model is empirically and statistically comparable to the SVM classifier and outperforms it in terms of time efficiency.     

Model checking temporal knowledge and commitments in multi-agent systems using reduction

Though modeling and verifying Multi-Agent Systems (MASs) have long been under study, there are still challenges when many different aspects need to be considered simultaneously. In fact, various frameworks have been carried out for modeling and verifying MASs with respect to knowledge and social commitments independently. However, considering them under the same framework still needs further investigation, particularly from the verification perspective. In this article, we present a new technique for model checking the logic of knowledge and commitments (CTLKC⁺). The proposed technique is fully-automatic and reduction-based in which we transform the problem of model checking CTLKC⁺ into the problem of model checking an existing logic of action called ARCTL. Concretely, we construct a set of transformation rules to formally reduce the CTLKC⁺ model into an ARCTL model and CTLKC⁺ formulae into ARCTL formulae to get benefit from the extended version of NuSMV symbolic model checker of ARCTL. Compared to a recent approach that reduces the problem of model checking CTLKC⁺ to another logic of action called GCTL¹, our technique has better scalability and efficiency. We also analyze the complexity of the proposed model checking technique. The results of this analysis reveal that the complexity of our reduction-based procedure is PSPACE-complete for local concurrent programs with respect to the size of these programs and the length of the formula being checked. From the time perspective, we prove that the complexity of the proposed approach is P-complete with regard to the size of the model and length of the formula, which makes it efficient. Finally, we implement our model checking approach on top of extended NuSMV and report verification results for the verification of the NetBill protocol, taken from business domain, against some desirable properties. The obtained results show the effectiveness of our model checking approach when the system scales up.