Finite-time adaptive fuzzy control for a class of output constrained nonlinear systems with dead-zone

The article investigates the finite-time adaptive fuzzy control for a class of nonlinear systems with output constraint and input dead-zone. First, by skillfully combining the barrier Lyapunov function, backstepping design method, and finite-time control theory, a novel adaptive state-feedback tracking controller is constructed, and the output constraint of the nonlinear system is not violated. Second, the fuzzy logic system is used to approximate unknown function in the nonlinear system. Third, the finite-time command filter is introduced to avoid the problem of “complexity explosion” caused by repeated differentiations of the virtual control signal in conventional backstepping control schemes. Meanwhile, a new saturation function is added in the compensating signal for filter error to improve control accuracy. Finally, based on Lyapunov stability analysis, all the signals of the closed-loop are proved to be semi-globally uniformly ultimately bounded, and the tracking error converges to a small neighborhood region of the origin in a finite time. A simulation example is presented to demonstrate the effectiveness for the proposed control scheme.     

Influence of pulse-jet cleaning pressure on performance of compact dust collector with pleated filter operated in clean-on-time mode

To operate a bag filter continuously, pulse-jet cleaning of dust particles from the filter medium is commonly required, and the pulse-jet pressure significantly affects the filter performance. In this study, the accumulation structure of residual dust particles inside and on the surface of a filter medium at different pulse-jet pressures was investigated by constructing a simple model, and the influence of the dust structure on the filter performance was clarified. Using a simple model, we determined the effective ratio of filtration area β, which represents the ratio of the filterable area to the total filtration area, the true resistance coefficient due to the primary dust layer ζ_p’ thinly deposited on the filter surface, and the true resistance coefficient inside the filter media itself ζ_f’_. The effective ratio of filtration area β decreased with operation time for all pulse-jet pressures; however, it maintained a high value when the pulse-jet pressure was high. The validity of β analyzed by the model was verified using two different methods, and the results showed good agreement, indicating that the model is effective in identifying real conditions. The true resistance coefficient due to the primary dust layer ζ_p’ decreased as the pulse-jet pressure increased; however, the true resistance coefficient inside the filter media itself ζ_f’ was the highest at 0.5 MPa. In addition, the dust collection efficiency was different at each pulse-jet pressure, which was considered to be caused by the difference in the dust particle accumulation structure.     

The effect of particle size distribution on the microstructure and properties of Al2O3 ceramics formed by stereolithography

Stereolithography (SL) shows advantages for preparing alumina-based ceramics with complex structures. The effects of the particle size distribution, which strongly influence the sintering properties in ceramic SL, have not been systematically explored until now. Herein, the influence of the particle size distribution on SL-manufactured alumina ceramics was investigated, including bending strength at room temperature, post-sintering shrinkage, porosity, and microstructural morphology. Seven particle size distributions of alumina ceramics were studied (in μm/μm: 30/5, 20/3, 10/2, 5/2, 5/0.8, 3/0.5, and 2/0.3); a coarse:fine particle ratio of 6:4 was maintained. At the same sintering temperature, the degree of sintering was greater for finer particle sizes. The particle size distribution had a larger influence on flexural strength, porosity and shrinkage than sintering temperature when the particle size distribution difference reached 10-fold but was weaker for 10 μm/2 μm, 5 μm/2 μm and 5 μm/0.8 μm. The sintering shrinkage characteristics of cuboid samples with different particle sizes were studied. The use of coarse particles influenced the accuracy of small-scale samples. When the particle size was comparable to the sample width, such as 30 μm/5 μm and 5 mm, the width shrinkage was consistent with the height shrinkage. When the particle size was much smaller than the sample width, such as 2 μm/0.3 μm and 5 mm, the width shrinkage was consistent with the length shrinkage. The results of this study provide meaningful guidance for future research on applications of SL and precise control of alumina ceramics through particle gradation.     

高等级生物安全实验室通风空调系统冗余设计原则探讨

对比分析了国内外标准有关高等级生物安全实验室通风空调系统冗余设计的要求。结合我国已有高等级生物安全实验室,重点分析了送风机、排风机、排风高效过滤器冗余设计的具体实施形式和存在的问题,给出了冗余设计原则建议。     

一种新的多渐消因子容积卡尔曼滤波

将强跟踪思想引入容积卡尔曼滤波（cubature Kalman filter，CKF），建立强跟踪CKF能有效克服CKF在模型不确定、状态突变等情况下，滤波性能下降的问题。通过分析现有多渐消因子计算方法，发现它们均只利用了协方差矩阵的对角线元素，并没有考虑各个状态之间的相关性，不能充分发挥多渐消因子的优势。为此，本文提出渐消因子矩阵，基于正交原理推导渐消因子矩阵的求解方法，提出多渐消因子强跟踪CKF算法。多渐消因子强跟踪CKF算法突破了传统多渐消因子为向量的限制，也不再要求渐消因子取值要大于1。仿真验证了算法具有更好的滤波精度何鲁棒性，能更好的满足工程应用的要求。     

基于残差决策的自动飞行控制系统远程实时故障诊断

针对自动飞行控制系统结构复杂、关联部件众多,发生故障时诊断时间长,从而影响飞机运行效率的问题,提出一种基于飞机通信寻址报告系统(ACARS)的远程实时故障诊断方案。首先,分析自动飞行控制系统的故障特点,设计搭建检测滤波器;然后,利用ACARS数据链实时发送的自动飞行控制系统的关键信息进行相关部件的残差计算,并根据残差决策算法进行故障诊断及定位;最后,针对不同故障部件残差间的差异大、决策门限无法统一的缺点,提出基于二次差值的残差决策改进算法,减缓了检测对象的整体变化趋势,降低了随机噪声和干扰的影响,避免了将瞬态故障诊断为系统故障的情况。实验仿真结果表明,基于二次差值的改进残差决策算法避免了多决策门限的复杂性,在采样时间为0.1 s的情况下,故障检测所需时间大约为2 s,故障检测时间大幅降低,有效故障检测率大于90%。     

A modified particle swarm optimization with multiple subpopulations for multimodal function optimization problems

In this paper, a modified particle swarm optimization (PSO) algorithm is developed for solving multimodal function optimization problems. The difference between the proposed method and the general PSO is to split up the original single population into several subpopulations according to the order of particles. The best particle within each subpopulation is recorded and then applied into the velocity updating formula to replace the original global best particle in the whole population. To update all particles in each subpopulation, the modified velocity formula is utilized. Based on the idea of multiple subpopulations, for the multimodal function optimization the several optima including the global and local solutions may probably be found by these best particles separately. To show the efficiency of the proposed method, two kinds of function optimizations are provided, including a single modal function optimization and a complex multimodal function optimization. Simulation results will demonstrate the convergence behavior of particles by the number of iterations, and the global and local system solutions are solved by these best particles of subpopulations.     

Carbon nanotube filter for heavy metal ion adsorption

This study investigated carbon nanotube filtration technology using catalyst particles supported on silicalite-1–biomorphic carbon materials (BCMs). Aqueous solutions of Mn(II), Cu(II), Cr(III), Cd(II), and Pb(II) were used to test the efficiency of heavy metal ions removal. Carbon nanotubes (CNTs) were synthesized and grown on BCMs by the chemical vapor deposition method catalyzed with the catalyst (Co, Fe, and Ni). The synthesized CNTs with Co– and Fe– nanoparticles were typically multi-walled carbon nanotubes, and they showed good crystallinity (I_D/I_G = 1.05) and yield of (11.10 and 8.86) %. The removal efficiency of Mn(II), Cu(II), Cr(III), Cd(II), and Pb(II) ions using Co-catalyzed CNT filter was 97.57%, 98.01%, 97.89%, 97.42%, and 99.99%, respectively.     

Multiobjective PSO based adaption of neural network topology for pixel classification in satellite imagery

The proposed work involves the multiobjective PSO based adaption of optimal neural network topology for the classification of multispectral satellite images. It is per pixel supervised classification using spectral bands (original feature space). This paper also presents a thorough experimental analysis to investigate the behavior of neural network classifier for given problem. Based on 1050 number of experiments, we conclude that following two critical issues needs to be addressed: (1) selection of most discriminative spectral bands and (2) determination of optimal number of nodes in hidden layer. We propose new methodology based on multiobjective particle swarm optimization (MOPSO) technique to determine discriminative spectral bands and the number of hidden layer node simultaneously. The accuracy with neural network structure thus obtained is compared with that of traditional classifiers like MLC and Euclidean classifier. The performance of proposed classifier is evaluated quantitatively using Xie-Beni and β indexes. The result shows the superiority of the proposed method to the conventional one.