沙漠地区高精度地震资料处理技术

受静校正及各种类型干扰的影响,西部沙漠地区地震资料的高精度处理较东部地区有更大的难度。对准噶尔盆地中部Ⅱ区、Ⅲ区、Ⅳ区、顺托果勒等区块地震资料在振幅恢复、静校正、去除各类噪音、高精度速度分析及叠前、叠后子波处理等方面进行了大量的试验与研究,形成了较为系统的高精度地震资料处理技术,在西部不同区块地震资料处理中取得了较好的应用效果。     

一种基于混沌同步的噪音衰减算法

论文提出了一种混沌通信系统的噪音衰减算法,该算法利用混沌同步现象在接收端获得正确的噪音估计值,从而从接收信号中滤除噪音恢复出正确的信号。通过数值仿真试验表明该方法是可行的。     

菱镁矿固硫特性的理论分析

对菱镁矿在固体燃料燃烧过程中的固硫特性进行了理论研究，所得结论对进一步将菱镁矿作为固体燃料燃烧过程中的固硫剂具有非常重要的意义。     

Σ-ΔA/D转换技术及仿真

Σ－ΔＡ／Ｄ转换技术近年来颇受重视，因为基于该技术的Ａ／Ｄ转换器能达到很高的分辨率（１６ｂｉｔ以上），并另具一系列优点。本文对Σ－ΔＡ／Ｄ转换器的基本原理，包括过采样（Ｏｖｅｒｓａｍｐｌｉｎｇ），噪声成形（ＮｏｉｓｅＳｈａｐｉｎｇ），以及数字抽取滤波（ＤｉｇｉｔａｌＤｅｃｉｍａｔｉｏｎＦｉｌｔｅｒｉｎｇ）等内容，均作了叙述。作者还对一个２０ｂｉｔΣ－Δ转换器的算法进行了计算机仿真。该转换器采用了高阶ＭＡＳＨ噪声成形技术，而其数字抽取滤波部分则由梳状滤波器与级联的半带滤波器构成。文章中给出了仿真结果。     

挠性胶管的阻尼减振机理初探

建立了挠性胶管阻尼耗能的简化模型。以此为基础分析了挠性胶管的阻尼耗能的一般规律,并得出了一些新的结论。     

舰船水声隐身技术(二)

本文探讨了水声隐身性能对舰船战技术性能的影响 ,舰船水噪声的主要噪声源、水噪声的治理措施及其展望。     

Quantitative demonstration and cost considerations of a software fault removal methodology

This paper presents a demonstration of a methodology for fault removal during software development. The methodology encompasses the entire development history, from system and software requirements generation to system test. Thus it considers not only the faults during software testing after formal configuration controls have been invoked, but also the faults discovered prior to that phase: during system and software requirements generation, preliminary design, detailed design and code and unit testing. The agents for fault discovery used in verification and validation are called activities, techniques and tools (AT & Ts) in this paper, each having a certain maximum potential or capability for fault discovery. The AT & Ts considered include the usual specification review activities, and also certain tools not normally applied in ‘standard’ software development, such as automated requirements aids. Application of the methodology yields numbers of residual faults as of each phase of development, including those remaining to be discovered during operations and maintenance. Some previous experience and data on residual faults correspond to these results, indicating that the methodology and choice of parameters are reasonable. The methodology also allows one to calculate a relative loss due to delay in fault discovery, which, as is well known, rises rapidly when faults are not discovered during the phase in which they are generated.     

高炉煤气脉冲布袋除尘技术的应用

介绍了韶钢6号高炉脉冲布袋除尘技术的工艺流程、主要设备、控制措施及节能效果。     

Corrosion Behavior of 316LN and 316 Stainless Steels During Long-term Exposure to Aerated 0.5 M NaCl Using Electrochemical Noise Technique

In the present work 316LN as well as 316 stainless steel (SS) coupons each of dimensions (0.025 × 0.018 × 0.006 m³) in well-polished condition were used as two nominal electrodes which were immersed in the aerated solution of 0.5 M NaCl. Correlated current and potential electrochemical noise (EN) signals were collected at 1 Hz sampling frequency for 1 h daily over a period of 30 days. The detrended EN data were used to calculate the noise resistance (R _N) as well as the spectral noise resistance at zero frequency (R _SN^o) values and other statistical parameters. To study the nature of pits and distribution of their diameters as well as depths, extensive observations of the pitted and the blank specimens were carried out using Confocal Laser Scanning Microscopy (CLSM). The current and the potential records of the two alloys showed distinct differences in their corrosion behavior. It was observed that within less than 4 h of immersion, 316SS showed signals indicative of unstable pitting and onset of stable pitting was noticed after 48 h of exposure. However, until about 24 h, 316LN showed just the random signals and unstable pitting was observed after 28 h. The signals clearly indicated continuous growth of the stable pits in 316SS as against the repassivation of the unstable pits in 316LN after 7 days exposure. It was observed that R _N values showed a continuous decrease in the case of 316SS, but were quite stable in the case of 316LN over the exposure period. Concurrent to these observations it was observed that 316SS specimen was extensively pitted. The frequency distributions of pit diameters as well pit depths were observed to be highest at 10-20 μm and 5-10 μm, respectively. However, pits with as large as 70-80 μm diameter and as deep as 20-25 μm too were observed. No pits were observed in case of 316LN even after 30 days of exposure, an observation that corroborates well with the stable R _N values. Thus, in the present investigation, the long-term tests using EN technique coupled with CLSM studies conclusively prove that many unstable pits initiated in 316SS turn into stable ones resulting in insidious localized corrosion attack whereas the unstable pits initiated in 316LN get passivated in the simulated coastal environment.