Experimental study of a refrigerant charged solar collector

The performance of a heat-pipe solar collector was investigated experimentally using refrigerants R11 as the working fluid. The unit is fabricated locally and its performance is evaluated under Beirut Solar conditions. The heat transfer from the heat pipes to the hot-water storage tank took place through a circular end condenser section of the heat-pipe integrated within the collector frame. Tests of single heat pipes showed that the thermal performance of the heat pipe were dependent on its tilt angle, condenser section length and configuration, and type of internal wick used. A circular condenser end of the heat-pipe performed better than a straight condenser due to increased surface area for heat transfer. The R11-charged solar collector with integrated condenser for secondary cooling of water had an efficiency in early operation hours that reached values higher than 60% for the forced circulation mode. The instantaneous system efficiencies varied from 60 to 20%, which are in the range of conventional water solar collectors. System response was fast and sensitive to the incident solar radiation. The thermosyphonic mode of the system operation generated build up of stored energy in the condenser, resulting in oscillating-type flow thus reducing system efficiency below values obtained with forced circulation. © 1998 John Wiley & Sons, Ltd.     

Experimental study of a multi-tube ICS solar water heating system in mild climates

Since a majority of residential and industrial building hot water needs are around 50°C, an integrated solar water heater could provide a bulk source that blends collection and storage into one unit. These collectors incorporate thermal storage within the collector itself. The storage pipe surface serves as the absorber surface. Most ICS systems use only one tank, but some use a number of tanks in series. While the simplicity of ICS systems is attractive, they are generally suitable only for applications in mild climates with small thermal storage requirements. A multi-tube ICS solar hot water system with eight cylindrical water storage tanks (pipes) in horizontal (East-West) orientation was designed and outdoor tests of experimental model were performed in mild climate of north (Caspian Sea) region of Iran. Experimental results such as water temperature profiles, mean daily efficiency, water temperature stratification and thermal losses during night are presented and discussed for this model. Experimental results showed that the daily mean efficiency is comparable to other ICS systems and also acceptable thermal performance of this type of ICS system has been observed.     

Performance enhancement of high temperature latent heat thermal storage systems using heat pipes with and without fins for concentrating solar thermal power plants

A key drawback of using latent heat thermal storage systems for concentrating solar thermal power plants is the low thermal conductivity of the phase change material during the melting and solidification processes. This paper investigates an approach for reducing the thermal resistance by utilising axially finned heat pipes. A numerical model simulating the phase change material melting and solidification processes has been developed. This paper also includes the models of the evaporation and condensation of the heat pipe working fluid. The results show that by adding four axial fins and including the evaporation and condensation, the overall thermal performance of the storage system is enhanced significantly compared to having bare heat pipes. After 3 h a total of 106% increase in energy storage is obtained during the charging process. The results also show that the combined effect of incorporating the evaporation/condensation process and adding the fins leads to a threefold increase in the heat storage during the first 3 h. During the discharge process, there was a 79% increase in energy discharged and also the combined effect of incorporating the evaporation/condensation as well as adding the fins results in an almost four fold increase in the heat extracted within the first 3 h. A parametric analysis has also been carried out to analyse the effect of the finned heat pipe parameters after incorporating evaporation and condensation of the heat pipe working fluid.     

Theoretical investigation of the performance of a novel loop heat pipe solar water heating system for use in Beijing,China

A novel loop heat pipe (LHP) solar water heating system for typical apartment buildings in Beijing was designed to enable effective collection of solar heat, distance transport, and efficient conversion of solar heat into hot water. Taking consideration of the heat balances occurring in various parts of the loop, such as the solar absorber, heat pipe loop, heat exchanger and storage tank, a computer model was developed to investigate the thermal performance of the system. With the specified system structure, the efficiency of the solar system was found to be a function of its operational characteristics - working temperature of the loop heat pipe, water flow rate across the heat exchanger, and external parameters, including ambient temperature, temperature of water across the exchanger and solar radiation. The relationship between the efficiency of the system and these parameters was established, analysed and discussed in detail. The study suggested that the loop heat pipe should be operated at around 72 °C and the water across the heat exchanger should be maintained at 5.1 l/min. Any variation in system structure, i.e., glazing cover and height difference between the absorber and heat exchanger, would lead to different system performance. The glazing covers could be made using either borosilicate or polycarbonate, but borosilicate is to be preferred as it performs better and achieves higher efficiency at higher temperature operation. The height difference between the absorber and heat exchanger in the design was 1.9 m which is an adequate distance causing no constraint to heat pipe heat transfer. These simulation results were validated with the primary testing results.     

Analytical study of the heat transfer limits of a novel loop heat pipe system

A novel loop heat pipe system was designed for use in solar hot water heating and an analytical model was developed to investigate its thermal performance and determine six major limits to system operation, i.e. capillary limit, entrainment limit, viscous limit, boiling limit, sonic limit, and filled liquid mass limit. Relations among the limits and several associated parameters, i.e. the heat pipe operating temperature, wicks type, heat pipe diameter, and height difference between the absorbing pipes array and condenser (heat exchanger), were established through a comprehensive analyses. It was found that the levels of capillary, entrainment, viscous, sonic, and filled liquid mass limits increased with the increasing temperature; however, the boiling limit was in the adverse trend. It was also found that the mesh screen wicks were able to obtain a higher capillary limit than sintered powder wicks, whilst other limits remained same. Larger pipe diameters would lead to higher operating limits. The height difference between the condenser (heat exchanger) and absorbing pipes (absorber) was the most important factor impacting on heat transfer capacities of the system, and largely affected the capillary limit of the system. It was noted when the pipe (inner) diameter increased to 5.6 mm or above, the governing limit of the system switched from entrainment to capillary. Relationship between the system governing limit, i.e. capillary limit, and the above addressed parameters were analysed. Adequate system configuration and operating conditions were suggested, which were summarized as follows: 6 mm of pipe inner diameter with mesh screen wicks, 58°C of heat pipe operating temperature, and 1.3 m height difference between absorber and condenser (heat exchanger). Copyright © 2010 John Wiley & Sons, Ltd.     

Improvements of gravity assisted wickless heat pipes

The performance of conventional gravity assisted heat pipes and modified heat pipes with a separator in the adiabatic section is investigated experimentally. Heat pipes with a three layered wick in the evaporator section, in addition to the separator, are investigated. The performance of the modified heat pipes was compared to a reference gravity assisted heat pipe. Experiments were conducted on heat pipes of three lengths with a common diameter at constant evaporator and condenser lengths. The effect of varying the adiabatic length was, thus, investigated distinctly in normal heat pipes and in modified heat pipes with a separator. Water was employed as the working fluid in all heat pipes. The experimental program included five inclination angles and a heat flux range form 5 to 32 kW/m². The presence of the adiabatic separator caused a marked improvement in all heat pipes tested for all lengths and inclination angles. A pronounced reduction in heat pipe evaporator temperature was obtained, which is accompanied by an improvement in the heat transfer coefficient. A correlation was developed for prediction of the heat transfer coefficient for gravity assisted heat pipes with an adiabatic separator. The correlation took into consideration the effect of the varying adiabatic length. The correlation was in good agreement with the experimental data.     

Optimization of a wickless heat pipe flat plate solar collector

The transient thermal behaviour of wickless heat pipe flat plate solar collectors has been analyzed with regard to various parameters. These parameters include global solar radiation intensity, inlet cooling water temperature, absorber plate material and thickness, ratio of pitch distance to wickless heat pipe diameter and ratio of condenser section length to total wickless heat pipe length. The results show that the selection of an absorber plate having a high value of conduction heat transfer rate per unit temperature difference is limited by the pitch distance.     

Enhancement of latent heat energy storage using embedded heat pipes

Latent heat thermal energy storage (LHTES) utilizing heat pipes or fins is investigated experimentally. Photographic observations, melting and solidification rates, and PCM energy storage quantities are reported. Heat pipe effectiveness is defined and used to quantify the relative performance of heat pipe-assisted and fin-assisted configurations to situations involving neither heat pipes nor fins. For the experimental conditions of this study, inclusion of heat pipes increases PCM melting rates by approximately 60%, while the fins are not as effective. During solidification, the heat pipe-assisted configuration transfers approximately twice the energy between a heat transfer fluid and the PCM, relative to both the fin-assisted LHTES and the non-heat pipe, non-fin configurations.     

A study on the new separate heat pipe refrigerator and heat pump

A new separate heat pipe refrigerator and heat pump is suggested based on the general three temperature thermal jet refrigerator and heat pump cycle. Sub-cooled hot water or other appropriate liquid heated by low grade heat sources forms the hot end and another heat pipe containing evaporator and condenser ends, adiabatic section of two-phase ejector and throttling tube is as the cold end of the separate heat pipe system. Performance relations for the thermal jet refrigerator and heat pump of such system is analyzed and a method of thermodynamic performance analysis is recommended. Primary prediction shows the feasibility of such heat pipe system for cold and warm water supply.     

The effects of multiple covers with condensation and optical degradation of a polyethylene windscreen on the performance of a sky cooling system

This study evaluates the performance of a heat-pipe-augmented sky radiator system modelled using MATLAB. It was developed to simulate thermal networks with the following nodes: polyethylene cover(s), radiator plate with selective surface, heat pipe condenser end, heat pipe evaporator end, thermal storage fluid, fluid container wall, and room. Applying a windscreen of polyethylene that is mostly transparent to long-wave radiation, a drawback is its susceptibility to optical property degradation. Sky fractions of 100% were possible in cities with small cooling loads (Rock Springs, Seattle, San Diego and Denver). Sky fractions of over 50% were achieved in New Orleans and Houston and over 40% in Miami. A second study examined the degradation of polyethylene cover material. Louisville and two challenging climates (Miami and New Orleans) were simulated. In the Louisville, Miami and New Orleans climate, performance was reduced by 2.7, 14.1 and 9.0%, respectively, due to degradation of the cover’s material.     

System optimization and experimental research on air source heat pump water heater

This paper deals with the system optimization of air source heat pump water heater (ASHPWH), including calculating and testing. The ASHPWH system consists of a heat pump, a water tank and connecting pipes. Air energy is absorbed at the evaporator and pumped to storage tank via a Rankine cycle. The coil pipe/condenser releases condensing heat of the refrigerant to the water side. An ASHPWH using a rotary compressor heated the water from initial temperature to the set temperature (55 °C). The capillary tube length, the filling quantity of refrigerant, the condenser coil tube length and system matching are discussed accordingly. From the testing results, it could be seen that the system performance COP could be improved obviously.     

Flower-type pulsating heat pipe for a solar collector

Inspired by the sunflower, we report a new structure of a solar collector that integrates a pulsating heat pipe (PHP) into a flat-plate collector. The proposed flower-type PHP solar collector is designed after a sunflower with petals that absorb sunlight and transfer nutrients to the stem after photosynthesis. The evaporator section adopts the shape of a flower to absorb sunlight fully, and the condenser section is rolled into a cylinder and placed in the lower part of the structure. A systematic experimental study is conducted upon start-up, and the performance characteristics, with acetone as the working fluid, are evaluated. We also did a heat loss analysis, which has a deviation of 8%. The effects of the mass flow rate of cooling water, filling ratio, length of the condenser section, and solar intensity are assessed. As the temperature of the heat absorber plate increases, the thermal resistance of the PHP can decrease to a minimum of 0.14°C/W. Under sunny weather conditions, the instantaneous thermal efficiency of the system with a filling ratio of 50% reaches 50%. Besides, we discussed the unstable operation conditions and possible dryout phenomenon that happened inside the PHP.     

Thermal performance of linear Fresnel reflecting solar concentrator with trapezoidal cavity absorbers

Thermal performance of the four identical trapezoidal cavity absorbers for linear Fresnel reflecting solar device were studied and compared. The absorbers were designed for operating in conjunction with a prototype Fresnel solar reflector. Rectangular and round pipe sections were used as absorber by placing in the trapezoidal cavity. The absorber pipes were coated with ordinary dull black board paint and black nickel selective surface. The bottom of the cavity was provided with plane glass to allow the solar radiation to be reflected from the Fresnel reflector. The other three sides of the cavity absorber were insulated to reduce heat loss. Thermal performance of the Fresnel reflecting concentrator with each trapezoidal cavity absorber was studied experimentally at different concentration ratio of the reflector. The study revealed that the thermal efficiency was influenced by the concentration ratio and selective surface coating on the absorber. The thermal efficiency decreased with the increase in the concentration ratio of the Fresnel reflecting collector. The selective surface coated absorber had a significant advantage in terms of superior thermal performance as compared to ordinary black painted absorber. The round pipe (multi-tube) receiver had higher surface area to absorb solar energy as compared to rectangular pipe receiver. Thermal efficiency of the solar device with round pipe absorber was found higher (up to 8%) as compared to rectangular pipe absorber.     

Optimal flow control of a forced circulation solar water heating system with energy storage units and connecting pipes

This paper focuses on pump flow rate optimization for forced circulation solar water heating systems with pipes. The system consists of: an array of flat plate solar collectors, two storage tanks for the circulation fluid and water, a heat exchanger, two pumps, and connecting pipes. The storage tanks operate in the fully mixed regime to avoid thermal stratification. The pipes are considered as separated components in the system so as to account for their thermal effects. The objective is to determine optimal flow rates in the primary and secondary loops in order to maximize energy transfer to the circulation fluid storage tank, while reaching user defined temperatures in the water storage tank to increase thermal comfort. A model is developed using mainly the first and second laws of thermodynamics. The model is used to maximize the difference between the energy extracted from the solar collector and the combined sum of the energy extracted by the heat exchanger and corresponding energies used by the pumps in the primary and secondary loops. The objective function maximizes the overall system energy gain whilst minimizing the sum of the energy extracted by the heat exchanger and corresponding pump energy in the secondary loop to conserve stored energy and meet the user requirement of water tank temperatures. A case study is shown to illustrate the effects of the model. When compared to other flow control techniques, in particular the most suitable energy efficient control strategy, the results of this study show a 7.82% increase in the amount of energy extracted. The results also show system thermal losses ranging between 5.54% and 7.34% for the different control strategies due to connecting pipe losses.     

A new type of solar water heater

This investigation reports a new type of solar water heating system without water pipes on the collector surface or a separate storage tank. The water to be heated continuously flows perpendicularly from an upper transparent cover to a porous absorber and is stored in a small volume beneath this assembly. Three different systems were designed, manufactured and tested but only one proved to be successful; this design indicated higher thermal efficiency compared to conventional collectors at high flow rates whereas at low flow rates the opposite is true.     

Effect of load pattern on solar-boosted heat pump water heater performance

The performance of a solar-boosted heat pump water heater (HPWH) operating under full load and part load conditions was determined in an outdoor experimental study. The system utilised flat unglazed aluminium solar evaporator panels to absorb solar and ambient energy. Absorbed energy was transferred to the water tank by means of the heat pump and a wrap around condenser coil on the outside of the tank. The system COP was found to be in the range of 5–7 under clear daytime conditions and 3–5 under clear night-time conditions. Using part load testing of the HPWH system it was found that concentrating the coils in the lower portion of the tank could increase the efficiency of the condenser coil. It was also shown that there exists a generalised linear relationship that can be used to describe the system COP in terms of the temperature difference between the water in the storage tank and the ambient air.     

Energy analysis and modeling of a solar assisted house heating system with a heat pump and an underground energy storage tank

An analytical model is presented and analyzed to predict the long term performance of a solar assisted house heating system with a heat pump and an underground spherical thermal energy storage tank. The system under investigation consists of a house, a heat pump, solar collectors and a storage tank. The present analytical model is based on a proper coupling of the individual energy models for the house, the heat pump, useful solar energy gain, and the transient heat transfer problem for the thermal energy storage tank. The transient heat transfer problem outside the energy storage tank is solved using a similarity transformation and Duhamel’s superposition principle. A computer code based on the present model is used to compute the performance parameters for the system under investigation. Results from the present study indicate that an operational time span of 5–7 years will be necessary before the system under investigation can attain an annually periodic operating condition. Results also indicate a decrease in the annually minimum value of the storage tank temperature with a decrease in the energy storage tank size and/or solar collector area.     

Numerical Study of Convection Melting Inside Ice Storage Systems by the Lattice Boltzmann Model

Abstract

The internal melt ice-on-coil tank with horizontal pipes is widely used in ice storage systems. The tank’s discharge process is greatly affected by the natural convection process that is caused by melting of the phase change material outside the pipes. To achieve an optimal arrangement of the pipes, a double-population lattice Boltzmann model was developed to simulate the transient solid-liquid phase change behavior in a section of an internal-melt ice-on-coil thermal storage tank with nine aligned built-in horizontal pipes. The evolutions in the phase change interface and melting rate was illustrated with different pipe shapes and pipe connections. Based on the melting rate, the whole melting process was divided into three stages: sharp decrease stage, continuous decrease stage, and snail-melting stage. The numerical results showed that a high melting rate was obtained by preferentially assigning the high-temperature pipes to the upper part of the tank, while a stable melting rate could be obtained when high-temperature pipes were preferentially assigned to the bottom part of the tank.     

Heat pipe with PCM for electronic cooling

This article experimentally investigates the thermal performances of a heat pipe with phase change material for electronic cooling. The adiabatic section of heat pipe is covered by a storage container with phase change material (PCM), which can store and release thermal energy depending upon the heating powers of evaporator and fan speeds of condenser. Experimental investigations are conducted to obtain the system temperature distributions from the charge, discharge and simultaneous charge/discharge performance tests. The parameters in this study include three kinds of PCMs, different filling PCM volumes, fan speeds, and heating powers in the PCM cooling module. The cooling module with tricosane as PCM can save 46% of the fan power consumption compared with the traditional heat pipe.     

Heat transfer aspects of an elevated linear absorber

This paper describes aspects of the design methodology and heat transfer calculations for an elevated north–south oriented linear absorber. The absorber is part of a direct steam generation solar thermal concentrating system based on the Australian compact linear Fresnel reflector (CLFR) concept. The basic absorber design is an inverted air cavity with a glass cover enclosing a selective surface. This arrangement has been shown previously to offer good optical and thermal performance from measurements on a 4 kW_thermal outdoor test apparatus. Two main design aims are discussed here: Firstly to maximise the heat transfer between the absorbing surface and the steam pipes, and secondly, to ensure that the absorber surface temperature is sufficiently uniform so as not to cause thermal degradation of the selective surface. Results are given of the absorber temperature distribution obtained from finite element analysis. Sufficiently low temperature differences between the fluid surface and the absorbing surface (<20 K) can be achieved with satisfactory pipe separations and sizes, and with practical absorber plate thicknesses.