咪唑类离子液体高效吸收二氯甲烷

合成了一系列常规离子液体1-丁基-3-甲基咪唑四氟硼酸盐([Bmim][BF4])、1-丁基-3-甲基咪唑六氟磷酸盐([Bmim][PF6])、1-丁基-3-甲基咪唑双三氟甲磺酰亚胺盐([Bmim][NTf2])、1-丁基-3-甲基咪唑双氰胺盐([Bmim][DCA])、1-丁基-3-甲基咪唑硫氰酸盐([Bmim][SCN])、1-乙基-3-甲基咪唑硫氰酸盐([Emim][SCN])和N-丁基吡啶硫氰酸盐([BPy][SCN]),用智能重量分析仪(IGA)测定不同温度和分压下离子液体吸收二氯甲烷(DCM)的容量。结果表明,[Bmim][SCN]具有最高的二氯甲烷吸收容量(1.46 g/g, 303.15 K, 60 kPa),5次循环后吸收能力无明显下降,[Bmim][SCN]基本可完全再生,能循环使用。量化计算结果表明[SCN]?可与二氯甲烷形成氢键,增强其对二氯甲烷的吸收能力。     

离子液体-水体系的相平衡

通过对1-丁基-3-甲基咪唑四氟硼酸盐([bmim][PF4])离子液体 水体系相平衡及NaCl、NaBF4和氯化1-丁基-3-甲基咪唑([bmim]Cl)对离子液体 水体系相平衡的影响进行了研究,结果表明: 离子液体[bmim][BF4] H2O二元体系具有典型的最高上临界溶解温度(UCST)行为,其最高上临界温度为5.3℃左右,临界组成为50%(水的质量分数); NaCl和NaBF4降低 [bmim][BF4] H2O体系的混溶性,而[bmim]Cl增加该体系的混溶性.由此得到一种简单定性地判断离子液体[bmim][BF4]中可能存在的杂质种类和水平的方法,并利用此结果可设计纯化该离子液体的绿色工艺.     

磺基琥珀酸二己酯钠盐表面活性剂

品种：1）磺基琥珀酸二正己酯钠盐；2）磺基琥珀酸二（α-乙基丁基）酯钠盐；3）磺基琥珀酸二（α-甲基戊基）酯钠盐；4）磺基琥珀酸二（4-甲基-α-戊基）酯钠盐。     

含离子液体乙腈-正丙醇体系的等压汽液平衡

常压(101.3 kPa)下, 测定了如下体系的汽液平衡数据:乙腈-正丙醇-氯化1-苄基-3-甲基咪唑([BzMIM][Cl])、乙腈-正丙醇-溴化1-苄基-3-甲基咪唑([BzMIM][Br])、乙腈-正丙醇-溴化1-己基-3-甲基咪唑([HMIM][Br]), 考察了3种离子液体对乙腈-正丙醇体系相平衡行为的影响。实验结果表明, 3种离子液体都能够提高乙腈对正丙醇的相对挥发度, 3种离子液体提高相对挥发度的顺序为 [BzMIM][Cl] > [BzMIM][Br] > [HMIM][Br]。用NRTL模型对测得的汽液平衡数据进行了关联, 关联结果与实验结果具有良好的一致性。     

1-丁基-3-甲基咪唑四氟硼酸盐离子液体的热分解动力学研究

利用非等温热重分析法(TG),研究了高纯氮气气氛下1-丁基-3-甲基咪唑四氟硼酸盐([bmim][BF4])的热分解动力学及机理函数。采用等转化率法和多元非线性回归法测定了[bmim][BF4]的热分解动力学。等转化率法表明[bmim][BF4]的活化能为E和指前因子logA分别为:198 kJ/mol和11.94 s-1。多元非线性回归法表明[bmim][BF4]的热分解机理模型函数为:n级自催化反应(Cn),反应级数为n=1.1426,所对应的机理模型函数为fα=1-α1.14261+1.0024α,指前因子logA和活化能E分别11.18 s-1和188 kJ/mol。另外,等转化率法和多元非线性回归法测得的活化能与量子化学计算法得到的活化能值均相吻合。     

磺基琥珀酸二己酯钠盐表面活性剂的结构与性能的关系

对由四种醇(正已醇,2-甲基戊醇、2-乙基丁醇和4-甲基-2戊醇)为原料,合成的四种不同己基的阴离子表面活性剂磺基琥珀酸二正己酯钠盐、磺基琥珀酸二(2-甲基戊基)酯钠盐、磺基琥珀酸二(2-乙基丁基)酯钠盐和磺基琥珀酸二(4-甲基2-戊基)酯钠盐表面化学和应用性能进行了测定,对这四种化合物的表面化学和应用性能与己基结构的关系进行了关联。结果表明：随着己基上支链数增加,化合物的表面张力和临界胶束浓度增加,己基、2-甲基戊基、2-乙基丁基和4-甲基-2．戊基,相应产物的表面张力(γCMC)分别为31．8,32．2,33．5和34／2mN／m,临界胶束浓度(CMC)分别为12．6,28．6,34．8和39．2mmol／L。随着己基上支链数增加,乳化能力、渗透性能和分散能力均减弱。     

烃基咪唑和吡啶鎓氢氧化物碱性离子液体的合成

以KOH或NaOH作碱试剂,考察了溶剂对1-丁基-3-甲基咪唑溴鎓([bmim]Br)合成1-丁基-3-甲基咪唑鎓氢氧化物([bmim]OH)碱性离子液体的影响,并采用强碱性阴离子交换树脂法合成[bmim]OH.结果表明:在室温下,溶剂10mL,[bmim]Br和KOH的物质的量之比为1:1.1的条件下,以乙醇为溶剂反...     

六氟磷酸盐对碳酸二甲酯-甲醇相平衡的影响

为验证1-丁基-3-甲基咪唑六氟磷酸盐([BMIM][PF_6])和1-辛基-3-甲基咪唑六氟磷酸盐([OMIM][PF_6])作为分离碳酸二甲酯+甲醇共沸体系萃取剂的可行性,在101.3 kPa下,用改进的Othmer釜测定了(甲醇+碳酸二甲酯+[BMIM][PF_6])和(甲醇+碳酸二甲酯+[OMIM][PF_6])的汽液平衡数据。用NRTL模型对汽液平衡实验数据进行了关联。实验结果表明:六氟磷酸阴离子液体的加入,使甲醇对碳酸二甲酯的相对挥发度增加,甲醇+碳酸二甲酯体系共沸点消失。在较高的甲醇摩尔分数下,[OMIM][PF_6]对甲醇的盐析作用略强于[BMIM][PF_6]。NRTL模型关联得出二元交互作用参数,可用于[BMIM][PF_6]和[OMIM][PF_6]分离碳酸二甲酯-甲醇物系的设计计算。     

咪唑类离子液体的合成与表征

通过两步法合成了阳离子含亲水性咪唑离子基和疏水烷基链结构、阴离子相同的1-乙基-3-甲基咪唑醋酸盐([Emim]Ac)、1-丁基-3-甲基咪唑醋酸盐([Bmim]Ac)、1-己基-3-甲基咪唑醋酸盐([Hmim]Ac)3种离子液体。利用红外光谱对其进行结构表征,并探究温度对pH的影响;考察温度、离子液体质量浓度、有机溶剂对电导率的影响;测定临界胶束浓度和溶解性。结果表明,[Emim]Ac、[Bmim]Ac、[Hmim]Ac碱性递减,其在不同溶剂中的电导率随温度(28～60℃)的升高、离子液体质量浓度(6～20 g/L)的增加而增大,且受溶剂性质影响;临界胶束浓度分别为11.46、9.92 g/L和9.72 g/L;其溶解性随溶剂极性的增强、侧链烷基的伸长而增大。     

离子液体支撑液膜的CO2/CH4分离性能

由于离子液体对CO₂具有较好的溶解选择性,离子液体支撑液膜分离CO₂越来越受到关注。比较了含3种不同阴离子的常规离子液体([bmim][BF₄]、[bmim][PF₆]、[bmim][Tf₂N])作为支撑液膜的液膜相分离CO₂/CH₄的性能,考察了咪唑环上烷基链长对离子液体支撑液膜性能的影响。考虑向离子液体中引入胺基和羧基等亲CO₂基团,制备了1-丁基-3-甲基咪唑丙氨酸离子液体([bmim][β-Ala]),考察了 [bmim][β-Ala]支撑液膜分离CO₂/CH₄的性能,并对在CO₂渗透测试前后的支撑液膜进行了FT-IR分析,发现氨基酸离子液体中的-NH₂和CO₂的较强作用以及该离子液体的高黏性影响了CO₂的透过性,使[Bmim][β-Ala]支撑液膜的CO₂透过率低。     

Surface tension and viscosity of 1-butyl-3-methylimidazolium iodide and 1-butyl-3-methylimidazolium tetrafluoroborate, and solubility of lithium bromide+1-butyl-3-methylimidazolium bromide in water

The surface tension and viscosity of 1-butyl-3-methylimidazolium iodide ([bmim][I]) and 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF₄]) were measured over a temperature range of 298. 15 to 323.15 K. It was found that both the viscosity and surface tension decrease with increasing temperature and that the surface tension and viscosity values of [bmim][I] were higher than those of [bmim][BF₄]. Additionally, the solubility of lithium bromide (2)+1-butyl-3-methylimidazolium bromide ([bmim][Br]) (3) in water (1) was measured at three different mass ratios (w₂/w₃=4 and 7, w₃=0) by using a visual polythermal method. The solubility of the suggested systems was better than that of lithium bromide in water.     

Physical and electrochemical properties of 1-butyl-3-methylimidazolium bromide, 1-butyl-3-methylimidazolium iodide,and 1-butyl-3-methylimidazolium tetrafluoroborate

The density, viscosity, refractive index, heat capacity, heat of dilution, ionic conductivity, and electrochemical stability of 1-butyl-3-methylimidazolium bromide ([bmim][Br]), 1-butyl-3-methylimidazolium iodide ([bmim][I]), and 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF₄]) were measured at room temperature or over a temperature range of 293.2 to 323.2 K. The density and refractive index values of [bmim][I] appeared to be the highest among three ionic liquids (ILs). However, the experimental viscosity values of [bmim][Br] were higher than those of [bmim][BF₄], while the heat capacities and heats of dilution of [bmim][BF₄] were higher than those of [bmim][Br]. The cyclic voltammogram of [bmim][br] and [bmim][BF₄] indicated electrochemical windows in the stability range from 2.7 V of [bmim][[Br] to 4.7 V of [bmim][BF₄].     

Purification of ionic liquids by supercritical CO2 monitored by infrared spectroscopy

Transmission infrared and Attenuated Total Reflection (ATR) in situ infrared spectroscopies were combined for the time-resolved monitoring of both liquid and supercritical phases during extraction of water and other impurities from ionic liquids with supercritical carbon dioxide (scCO₂). Cleaning and drying by scCO₂ at 100 bar and 40 °C proved to be efficient for all ionic liquids tested, including 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF₄]), 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF₆]), and 1-butyl-3-methylimidazolium trifluoromethansulfonate ([bmim][TfO] or [bmim] triflate). Despite the moderate solubility of water in scCO₂ compared to other classical solvents, the amount of water decreased continuously during the drying. The extraction could be followed by simple transmission IR spectroscopy of the supercritical phase. During the extraction, organic impurities and water were removed rapidly from the ionic liquid phase as scCO₂ improved the transport properties in the ionic liquids.     

有机物在离子液体中无限稀释活度因子及液液界面张力的定量机构-性质关系

用PM3半经验量子化学方法计算了烷烃、烯烃和芳烃等的疏水性参数lgP、偶极矩、前线分子轨道能隙和水合能等结构描述符,与实验测定的烃类在1-丁基-3-甲基咪唑六氟磷酸盐（［C₄MIM］［PF₆］）、1-烯丙基-3-甲基咪唑四氟硼酸盐（［AMIM］［BF₄］）、1-异丁烯基-3-甲基咪唑四氟硼酸盐（［MPMIM］［BF₄］）和［MPMIM］［BF₄］-AgBF₄ 4种离子液体中的无限稀释活度因子进行定量结构-性质关系（QSPR）研究,建立的QSPR模型具有良好的关联和预测能力.同时测定了烃类等溶质与离子液体［C₄MIM］［PF₆］的液液界面张力,发现其与无限稀释活度因子有相似的变化趋势,据此采用同样的结构描述符,建立了溶质与［C₄MIM］［PF₆］界面张力的QSPR模型,模型的关联能力良好.     

离子液体[bmim][Tf2N]的分子动力学模拟

建立了离子液体1-正丁基3-甲基咪唑双（三氟甲基磺酰基）酰亚胺（[bmim][Tf₂N]）的全原子模型,并分别在五种不同的温度和五种不同的压力下对其进行了分子动力学模拟。将[bmim][Tf₂N]密度的模拟结果与实验结果进行了比较,两者吻合良好,验证了模型准确性。此外,还对[bmim][Tf₂N]内部的相互作用能随温度和压力的变化规律进行了分析,结果表明：离子液体内部的库仑能、范德华能、长程作用能均随温度的升高而增加,系统达到平衡所需时间随之变短;相对温度而言,压力对离子液体内部相互作用能的影响较小;在各种相互作用能中,范德华能随温度和压力的变化最大;温度和压力对离子液体的构型不会产生影响。     

Desulfurization of Diesel Fuel by Extraction with Lewis-Acidic Ionic Liquid

Abstract

Ionic liquids were found to be highly selective for the extractive removal of aromatic sulfur compounds from fuels at room temperature. The efficiency of ionic liquids for the removal of aromatic sulfur compounds is dependent on the properties and structure of the ionic liquids. In this work, the Lewis-acidic ionic liquid 1-butyl-3-methylimidazolium tetrahalogenoferrate(III) ([BMIM] [FeCl₄]) was synthesized and demonstrated to be more effective for the removal of aromatic sulfur compounds from diesel over ionic liquids 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF₆]) and 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM] [BF₄]) because of its Lewis-acidic property. The ionic liquids favorably extracted organic compounds with a higher density of aromatic π-electrons. [BMIM][FeCl₄] ionic liquid can be regenerated through reextraction by hexane, and could be used in multiple steps for the removal of sulfur compounds from diesel.     

Critical properties and acentric factors of ionic liquids

Since most ionic liquids (ILs) decompose before reaching their critical state, the experimental measurement of their critical properties are not possible. In this study, the critical temperatures, critical pressures and acentric factors of ten commonly investigated ILs were determined by making an optimum fit of the calculated vapor-liquid equilibrium data of binary mixtures of CO₂+IL to the experimental values found in literature. For this purpose, the Peng-Robinson equation of state (PR EoS) and the differential evolution optimization method were used. The ILs considered were 1-ethyl-3-methylimidazolium hexafluorophosphate ([emim][PF₆]), 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide ([emim][Tf₂N]), 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF₄]), 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF₆]), 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide ([bmim][Tf₂N]), 1-hexyl-3-methylimidazolium tetrafluoroborate ([hmim][BF₄]), 1-hexyl-3-methylimidazolium hexafluorophosphate ([hmim][PF₆]), 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide ([hmim][Tf₂N]), 1-octyl-3-methylimidazolium tetrafluoroborate ([omim][BF₄]) and 1-octyl-3-methylimidazolium hexafluorophosphate ([omim][PF₆]). To evaluate the ability of the determined parameters in predicting the phase behavior of systems other than the systems that were used for parameter optimization, both sets of parameters obtained in this work and that of Valderrama et al. were used to predict bubble-point pressures of CHF₃+[bmim][PF₆] (by using the PR EoS and the Soave-Redlich-Kwong equation of state. The bubble-point pressures of CO₂+IL systems optimized in this study by the PR EoS were also determined using the Soave-Redlich-Kwong equation of state (SRK EoS). In addition, liquid densities of pure ILs were predicted using a generalized correlation proposed by Valderrama and Abu-Shark. In all cases, the various predicted properties of these ten ILs, were in better agreement with the experimental data, using the critical properties and acentric factor obtained in this study, compared to the values suggested by Valderrama et al.     

乙腈+[C4mim][Cl]、乙腈+[C4mim][BF4]、乙腈+[C6mim][Cl]的气液平衡测定与关联（英文）

Vapor pressures were measured for acetonitrile+1-butyl-3-methylimidazolium chloride ([C4mim][Cl]),+1-butyl-3-methylimidazolium tetrafluoroborate ([C4mim][BF4]) and+1-hexyl-3-methylimidazolium chloride ([C6mim][Cl]) at temperatures of 313 to 353 K by a quasi-static method. The experimental data for the binary sys-tems were correlated by the non-random two liquid (NRTL) equation with an average absolute relative deviation (AARD) of within 1.84%. The results indicate that the three ionic liquids (ILs) can result in a negative deviation from the Raoult's law for the binary solutions containing acetonitrile, and the affinity between ILs and acetonitrile mole-cules fol ows the order [C4mim][BF4]+acetonitrile N [C4mim][Cl]+acetonitrile N [C6mim][Cl]+acetonitrile.     

High-pressure solubility of carbon dioxide in imidazolium-based ionic liquids with anions [PF6] and [BF4]

The solubility of carbon dioxide in three ionic liquids (ILs) under supercritical fluid condition was measured at pressures up to 32 MPa and at temperatures of 313.15, 323.15, and 333.15 K in a high-pressure view cell. The imidazolium-derivative ionic liquids 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF₆]), 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF₄]), and 1-octyl-3-methylimidazolium tetrafluoroborate ([omim][BF₄]) were employed in this research. The effects of pressure, temperature, nature of anion and cation as well as the water content on the solubility of CO₂ in the ILs were investigated experimentally. The solubility of CO₂ in the IL was higher for the ILs with longer cationic alkyl group and for the ILs with lower anion polarity. The lower the water content or the lower the temperature as well as the higher the pressure, the higher was the solubility of CO₂.     

Vapor pressure measurement and correlation of acetonitrile+1-butyl-3-methylimidazolium chloride,+1-butyl-3-methylimidazolium tetrafluoroborate,and+1-hexyl-3-methylimidazolium chloride

Vapor pressures were measured for acetonitrile+1-butyl-3-methylimidazolium chloride ([C4mim][Cl]),+1-butyl-3-methylimidazolium tetrafluoroborate ([C4mim][BF4]) and+1-hexyl-3-methylimidazolium chloride ...