铜晶体的疲劳损伤微观机制

对Cu单晶体、双晶体和多晶体疲劳损伤微观机制的总结结果表明：在中、低应变范围Cu单晶体的疲劳裂纹主要沿驻留滑移带萌生,而在高应变范围则沿粗大形变带萌生;Cu双晶体中疲劳裂纹总是优先沿大角度晶界萌生和扩展,而小角度晶界则不萌生疲劳裂纹;对于Cu多晶体,疲劳裂纹主要沿大角度晶界萌生,有时也沿驻留滑移带萌生,而孪晶界面两侧由于滑移系具有相容的变形特征而未观察到疲劳裂纹萌生．     

Al双晶体的晶界疲劳效应SCIEI

通过Al双晶体疲劳试验,研究了晶界对循环变形和疲劳裂纹扩展的影响。实验结果表明,晶界疲劳效应集中体现于晶界影响区,表现为不相容塑性应变在该区内产生内应力,并由此可激发次级滑移,甚至产生晶界裂纹;在常幅循环应力下,随超Ⅰ阶段裂纹逐渐接近晶界,裂纹分叉、前沿碎裂,扩展速率降低,直至在晶界影响区中央达到一最小值。本文提出了晶界诱发裂纹顶端屏蔽机制,并以此解释了上述超Ⅰ阶段裂纹对微观组织敏感的扩展行为。     

金属材料疲劳损伤的界面效应

总结了不同金属材料在低周疲劳过程中典型的晶界、孪晶界、相界和微电子互连界面的损伤开裂行为. 纯Cu中疲劳裂纹萌生的难易顺序为: 小角度晶界、驻留滑移带和大角度晶界. 对于纯Cu与铜合金中退火孪晶界, 是否萌生疲劳裂纹与合金成分有关, 随合金元素的加入降低了层错能, 退火孪晶界相对容易萌生疲劳裂纹. 对于Cu--Ag二元合金, 由于存在不同的晶界和相界面, 是否萌生疲劳裂纹取决于界面两侧晶体的取向差, 通常两侧取向差大的界面容易萌生疲劳裂纹. 在微电子互连界面中, 疲劳裂纹萌生位置与焊料成分和时效时间有关,对于Sn--Ag/Cu互连界面, 疲劳裂纹通常沿焊料与界面化合物结合处萌生; 对于Sn--Bi/Cu互连界面, 随时效时间增加会出现明显的由于Bi元素偏聚造成的界面脆性.     

铜双晶体中晶界及组元晶体的疲劳寿命

本文对具有单,双滑移取向组元晶体的近生趣晶界铜双晶体进行拉－拉循环变形,得出铜双晶体中晶界及组元晶体的Ｓ－Ｎ曲线,比较了铜双晶体晶界及组元晶体疲劳寿命的差别,发现在相同的应力幅下晶界的疲劳寿命明显低于组元晶体的疲劳寿命。     

不同应力状态下6063铝合金断裂机制原位拉伸研究

用SEM-520原位拉伸实验对可以实现不同应力的6063铝合金试件的断裂过程做了详细研究和分析.研究结果表明:不同应力状态下的铝合金试样在拉伸过程在其表面上都产生了大量的滑移带,但断裂机制不同.随着三轴应力度的降低,断裂从正断向剪断过渡,试件断口也由韧窝断裂模式向剪切断裂模式演变;6063铝合金晶界是其最薄弱环节,大量微裂纹产生于晶界,随着载荷的增加,微裂纹长大和扩展,与此同时,在局部变形带中沿晶界和滑移带又产生了新的微裂纹,微裂纹之间通过扩展或剪切而连接导致试样断裂;试样最小截面上的三轴应力度越小,试样断口的2个面上韧窝的取向越明显,而且断口越光滑.     

EFFECT OF ZIGZAG GRAIN BOUNDARY ON CREEP RUPTURE OF A 10Cr-15Co-Ni-BASE WROUGHT SUPERALLOY

应用两种热处理制度分别获得弯曲晶界和平直晶界,研究两种晶界状态对10Cr-15Co-Ni基变形高温合金蠕变断裂过程的影响,重点探讨弯曲晶界改善合金热强性原因。研究表明,弯曲晶界对裂纹的萌生、长大及扩展,对裂纹的形态及断裂方式,都有显著的影响。弯曲晶界能有力地阻止晶界滑动及推迟裂纹连接,使晶内参与更多的变形,弯晶的主要作用体现在蠕变第三阶段。合金经弯晶处理后蠕变断裂寿命提高26％。     

弯曲晶界对10Cr-15Co-Ni基变形高温合金蠕变断裂的影响

应用两种热处理制度分别获得弯曲晶界和平直晶界,研究两种晶界状态对10Cr-15Co-Ni基变形高温合金蠕变断裂过程的影响,重点探讨弯曲晶界改善合金热强性原因。研究表明,弯曲晶界对裂纹的萌生、长大及扩展,对裂纹的形态及断裂方式,都有显著的影响。弯曲晶界能有力地阻止晶界滑动及推迟裂纹连接,使晶内参与更多的变形,弯晶的主要作用体现在蠕变第三阶段。合金经弯晶处理后蠕变断裂寿命提高26％。     

不同应力状态下铝合金变形及损伤机理的研究

利用改装的Arcan夹具对铝合金（6063）的蝶形试样进行0°，30°，45°，60°，90°的拉伸及拉伸卸载试验，研究了铝合金在不同应力状态下变形及损伤机理。结果表明：铝合金在不同应力状态下的工程应力一应变曲线明显不同。0°加载时，在蝶形中心产生微孔洞，微孔洞之间剪切，从而产生了微裂纹。随着微裂纹的扩展、连接导致试样断裂。随着试样中三轴应力度的减小，在蝶形试样中心的剪切应力不断增大，同时在蝶形试样中的剪切变形带越来越集中。显微裂纹首先在剪切带中产生，随着微裂纹的扩展导致试样的断裂。90°拉伸时，在蝶形中心形成明显的剪切变形带。90°加载时，在试样中产生的剪切带是形变剪切带而非相变剪切带。利用有限元软件ABAQUS对不同角度拉伸试验进行模拟，从而得出了不同应力状态下的塑性区的形状和大小。     

热轧参数对铸态AZ91镁合金组织与性能的影响

通过不同道次压下量和轧制道次的热轧成形实验,研究了不同变形条件对AZ91铸态镁合金组织和析出相演变的影响,以及合金在热轧变形中的开裂行为。实验结果表明:对AZ91镁合金多道次、小压下量轧制是实现其累积大塑性变形的途径之一。在实验轧制条件下,AZ91镁合金塑性变形仍以孪生变形为主,动态再结晶并未明显进行,仅在晶界及析出相附近发生部分不连续动态再结晶。轧制变形过程中,β-Mg_(17)Al_(12)相呈短条棒状或颗粒状分布于晶界附近,且尺寸更为细小。在晶界附近分布的脆性析出相成为微裂纹萌生的源头,随着累积变形量的增加,部分Mg_(17)Al_(12)相被轧碎形成二次裂纹,裂纹进一步沿晶界扩展,造成明显开裂现象。     

海洋柔性立管用钢的疲劳断裂行为

采用GPS100高频疲劳试验机研究了海洋柔性立管用钢在温轧工艺下的疲劳断裂行为。结果表明,海洋柔性立管用钢疲劳寿命随加载应力幅的升高而不断下降;疲劳裂纹产生于试样表面,裂纹源区可见变形带及河流花样,裂纹扩展区存在大量二次裂纹,瞬断区疲劳裂纹呈韧性断裂特征。在疲劳裂纹扩展过程中,裂纹的扩展能力因大角度晶界的铁素体和高强度贝氏体的相互作用而受到限制,同时在晶界处形成的二次裂纹同样可减缓扩展速率,达到提高疲劳寿命的效果。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

THERMODYNAMICS STUDY ON THE DECOMPOSITION OF CHROMITE WITH KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

INFLUENCE OF HEAT TREATMENT ON DAMPING BEHAVIOUR OF THE MAGNESIUM WROUGHT ALLOY AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.