6BTA 5.9 G2-1 Cummins engine performance and emission tests using methyl ester mahua (Madhuca indica) oil/diesel blends

Neat mahua oil poses some problems when subjected to prolonged usage in CI engine. The transesterification of mahua oil can reduce these problems. The use of biodiesel fuel as substitute for conventional petroleum fuel in heavy-duty diesel engine is receiving an increasing amount of attention. This interest is based on the properties of bio-diesel including the fact that it is produced from a renewable resource, its biodegradability and potential to exhaust emissions. A Cummins 6BTA 5.9 G2- 1, 158 HP rated power, turbocharged, DI, water cooled diesel engine was run on diesel, methyl ester of mahua oil and its blends at constant speed of 1500 rpm under variable load conditions. The volumetric blending ratios of biodiesel with conventional diesel fuel were set at 0, 20, 40, 60, and 100. Engine performance (brake specific fuel consumption, brake specific energy consumption, thermal efficiency and exhaust gas temperature) and emissions (CO, HC and NOx) were measured to evaluate and compute the behavior of the diesel engine running on biodiesel. The results indicate that with the increase of biodiesel in the blends CO, HC reduces significantly, fuel consumption and NOx emission of biodiesel increases slightly compared with diesel. Brake specific energy consumption decreases and thermal efficiency of engine slightly increases when operating on 20% biodiesel than that operating on diesel.     

The use of Koroch seed oil methyl ester blends as fuel in a diesel engine

An experimental investigation was carried out on a small direct injection (DI) diesel engine, fuelling the engine with 10% (B10), 20% (B20), 30% (B30) and 40% (B40) blending of Koroch seed oil methyl ester (KSOME) with diesel. The performance and combustion characteristics of the engine at various loads are compared and analyzed. The results showed higher brake specific fuel consumption (BSFC) and lower brake thermal efficiency (BTE) for the KSOME blends. The engine indicated power (IP) was more for the blends up to B30, but found to be reduced for the blend B40 when compared to that of diesel. The engine combustion parameters such as pressure crank angle diagram, peak pressure, time of occurrence of peak pressure, net heat-release rate, cumulative heat release, ignition delay and combustion duration were computed. The KSOME blends exhibited similar combustion trend with diesel. However, the blends showed an early start of combustion with shorter ignition delay period. The study reveals the suitability of KSOME blends up to B30 as fuel for a diesel engine mainly used in generating sets and the agricultural applications in India without any significant drop in engine performance.     

Heat release and engine performance effects of soybean oil ethyl ester blending into diesel fuel

The engine performance impact of soybean oil ethyl ester blending into diesel fuel was analyzed employing heat release analysis, in-cylinder exergy balances and dynamometric tests. Blends with concentrations of up to 30% of soybean oil ethyl ester in volume were used in steady-state experiments conducted in a high speed turbocharged direct injection engine. Modifications in fuel heat value, fuel-air equivalence ratio and combustion temperature were found to govern the impact resulting from the addition of biodiesel on engine performance. For the analyzed fuels, the 20% biodiesel blend presented the best results of brake thermal efficiency, while the 10% biodiesel blend presented the best results of brake power and sfc (specific fuel consumption). In relation to mineral diesel and in full load conditions, an average increase of 4.16% was observed in brake thermal efficiency with B20 blend. In the same conditions, an average gain of 1.15% in brake power and a reduction of 1.73% in sfc was observed with B10 blend.     

Performance of jatropha oil blends in a diesel engine

Results are presented on tests on a single-cylinder direct-injection engine operating on diesel fuel, jatropha oil, and blends of diesel and jatropha oil in proportions of 97.4%/2.6%; 80%/20%; and 50%/50% by volume. The results covered a range of operating loads on the engine. Values are given for the chemical and physical properties of the fuels, brake specific fuel consumption, brake power, brake thermal efficiency, engine torque, and the concentrations of carbon monoxide, carbon dioxide and oxygen in the exhaust gases. Carbon dioxide emissions were similar for all fuels, the 97.4% diesel/2.6% jatropha fuel blend was observed to be the lower net contributor to the atmospheric level. The trend of carbon monoxide emissions was similar for the fuels but diesel fuel showed slightly lower emissions to the atmosphere. The test showed that jatropha oil could be conveniently used as a diesel substitute in a diesel engine. The test further showed increases in brake thermal efficiency, brake power and reduction of specific fuel consumption for jatropha oil and its blends with diesel generally, but the most significant conclusion from the study is that the 97.4% diesel/2.6% jatropha fuel blend produced maximum values of the brake power and brake thermal efficiency as well as minimum values of the specific fuel consumption. The 97.4%/2.6% fuel blend yielded the highest cetane number and even better engine performance than the diesel fuel suggesting that jatropha oil can be used as an ignition-accelerator additive for diesel fuel.     

The experimental study on the performance,combustion and emission characteristics of a diesel engine using diesel – biodiesel – diethyl ether blends

ABSTRACT

In the present research work, the experimental analysis has been executed to investigate the influence of diethyl ether as an oxygenated additive to the diesel-biodiesel blend on the performance, combustion and emission characteristics of a diesel engine. The biodiesel (Frying oil methyl ester) was prepared by the transesterification process, and the biodiesel was added (40% by volume) to the diesel fuel to prepare the diesel-biodiesel blend (D60FME40). The diethyl ether was added to the diesel-biodiesel blends D60FM35 (diesel 60% + biodiesel 35% by volume) and D60FM30 (diesel 60% + biodiesel 30% by volume) with suitable volume proportions of 5% and 10% respectively to form diesel-biodiesel-diethyl ether blends ((D60FM35DEE5) & (D60FM30DEE10)). Initially, the test was conducted with diesel fuel to obtain the baseline reference reading. Then, the reading was compared with results taken from the engine using a diesel-biodiesel blend (D60FME40) and diethyl ether blends (D60FM35DEE5) & (D60FM30DEE10). The results reveal that the maximum brake thermal efficiency was obtained with diesel fuel and it was higher than the diesel-biodiesel blend and diethyl ether blends. The peak in-cylinder gas pressure and heat release rate in the premixed stage was less for the diesel-biodiesel blend, but it was increased with the addition of diethyl ether to the blend. The diesel-biodiesel-diethyl ether blends show less carbon monoxide and hydrocarbon emissions except for NO_X emission as compared to the diesel and diesel-biodiesel blend, especially at the engine rated power.     

A study on the performance and emission of a diesel engine fueled with Jatropha biodiesel oil and its blends

Biodiesel either in neat form or as a mixture with diesel fuel is widely investigated to solve the twin problem of depletion of fossil fuels and environmental degradation. The main objective of the present study is to compare performance, emission and combustion characteristics of biodiesel derived from non edible Jatropha oil in a dual fuel diesel engine with base line results of diesel fuel. The performance parameters evaluated were: brake thermal efficiency, brake specific fuel consumption, power output. As a part of combustion study, in-cylinder pressure, rate of pressure rise and heat release rates were evaluated. The emission parameters such as carbon monoxide, carbon dioxide, un-burnt hydrocarbon, oxides of nitrogen and smoke opacity with the different fuels were also measured and compared with base line results. The different properties of Jatropha oil after transestrification were within acceptable limits of standards as set by many countries. The brake thermal efficiency of Jatropha methyl ester and its blends with diesel were lower than diesel and brake specific energy consumption was found to be higher. However, HC, CO and CO₂ and smoke were found to be lower with Jatropha biodiesel fuel. NO_x emissions on Jatropha biodiesel and its blend were higher than Diesel. The results from the experiments suggest that biodiesel derived from non edible oil like Jatropha could be a good substitute to diesel fuel in diesel engine in the near future as far as decentralized energy production is concerned. In view of comparable engine performance and reduction in most of the engine emissions, it can be concluded and biodiesel derived from Jatropha and its blends could be used in a conventional diesel engine without any modification.     

Evaluating combustion,performance and emission characteristics of diesel engine using karanja oil methyl ester biodiesel blends enriched with HHO gas

With a specific end goal to take care of the worldwide demand for energy, a broad research is done to create alternative and cost effective fuel. The fundamental goal of this examination is to investigate the combustion, performance and emission characteristics of diesel engine using biodiesel blends enriched with HHO gas. The biodiesel blends are gotten by blending KOME obtained from transesterification of karanja oil in various proportions with neat diesel. The HHO gas is produced by the electrolysis of water in the presence of sodium bicarbonate electrolyte. The constant flow of HHO gas accompanied with biodiesel guarantees lessened brake specific fuel consumption by 2.41% at no load and 17.53% at full load with increased the brake thermal efficiency by 2.61% at no load and 21.67% at full load contrasted with neat diesel operation. Noteworthy decline in unburned hydrocarbon, carbon monoxide, carbon-dioxide emissions and particulate matter with the exception of NO_x discharge is encountered. The addition of EGR controls this hike in NO_x with a slight decline in the performance characteristics. It is clear that the addition of HHO gas with biodiesel blends along with EGR in the test engine improved the overall characterization of engine.     

Performance, emission and combustion characteristics of biodiesel fuelled variable compression ratio engine

Experiments has been carried out to estimate the performance, emission and combustion characteristics of a single cylinder; four stroke variable compression ratio multi fuel engine fuelled with waste cooking oil methyl ester and its blends with standard diesel. Tests has been conducted using the fuel blends of 20%, 40%, 60% and 80% biodiesel with standard diesel, with an engine speed of 1500 rpm, fixed compression ratio 21 and at different loading conditions. The performance parameters elucidated includes brake thermal efficiency, specific fuel consumption, brake power, indicated mean effective pressure, mechanical efficiency and exhaust gas temperature. The exhaust gas emission is found to contain carbon monoxide, hydrocarbon, nitrogen oxides and carbon dioxide. The results of the experiment has been compared and analyzed with standard diesel and it confirms considerable improvement in the performance parameters as well as exhaust emissions. The blends when used as fuel results in the reduction of carbon monoxide, hydrocarbon, carbon dioxide at the expense of nitrogen oxides emissions. It has found that the combustion characteristics of waste cooking oil methyl ester and its diesel blends closely followed those of standard diesel.     

Effect of diethyl ether additive in Jatropha biodiesel-diesel fuel blends on the variable compression ratio diesel engine performance and emissions characteristics at different loads and compression ratios

An investigational analysis was performed to assess the effect of diethyl ether (DEE) that acts as an oxygenated additive in Jatropha biodiesel and diesel fuel blends on the performance enhancement and emission reduction of a variable compression ratio (CR) diesel engine. The DEE (10% vol) is added to different concentration levels of Jatropha biodiesel (B5, B10, and B20). The Jatropha biodiesel (JME) is prepared by the transesterification reaction and DEE is prepared through acid distillation of ethanol. The various tests were conducted by varying the loads at 25%, 50%, 75%, and 100% (3, 6, 9, and 12 kg). The DEE was entirely miscible with diesel and Jatropha biodiesel, the addition of DEE increases the cetane and calorific value, kinematic viscosity of the fuel blends compared with neat diesel or Jatropha biodiesel. The results illustrate that at higher loads and CRs, the engine performance parameters such as brake thermal efficiency enhances and reduces the brake-specific fuel consumption for DEE-Jatropha biodiesel-diesel fuel blends. Blend A3 (10% DEE + 20% JME + 70% diesel) demonstrated an overall improvement in the engine performance parameters and emission characteristics compared with A1, A2, and diesel fuel blends. It is concluded that the DEE-JME-diesel fuel blend is a promising source of fuel for diesel engine at maximum load.     

Combined impact of varying biogas mass flow rate and rice bran methyl esters blended with diesel on a dual-fuel engine

ABSTRACT

For fetching day-to-day energy needs, current energy requirement majorly depends on fossil fuels. But ambiguous matter like abating petroleum products and expanding air pollution has enforced the experts to strive for another fuel which can be used as an alternative or reduce the applications of fossil fuels. Considering the issues, the main objective of the present study is to find the feasibility by using blends of rice bran oil biodiesel and diesel which are used as pilot fuels by blending 10% and 20% biodiesel in fossil diesel and biogas, introduced as gaseous fuel by varying its mass flow rate in a dual-fuel engine mode. An experimentation study was carried out to find the performance and emission parameters of the engine relative to pure diesel. The results were very much similar to the majority of researchers who used biodiesel and gaseous fuels in a dual-fuel engine. Brake specific fuel consumption (BSFC) of the engine was noticed to have increased, while brake thermal efficiency was on the lower side in dual fuel mode in comparison with regular diesel. In relation with conventional diesel, it was noticed that combined effect of rice bran methyl esters and varying mass flow rate of biogas showed a decrement in NO _x and smoke emissions, whereas HC and CO exhalations were on higher side when biogas and biodiesel were utilized collectively in dual-fuel engine. Hence, it was concluded that combination of blends of biodiesel and diesel and introduction of biogas in the engine can be a promising combination which can be used as a substitute fuel for addressing future energy needs.     

Analysis of blended fuel properties and engine performance with palm biodiesel–diesel blended fuel

Depleting fossil fuel sources accompanied by continuously growing energy demands lead to increased interest in alternative energy sources. Blended biodiesel–diesel fuel has been approved as a commercial fuel at a low blending ratio. However, problems related to fuel properties are persistent at high blending ratios. Hence, in this study, the feasibility of biodiesel produced from palm oil was investigated. Characterization of blended fuel properties with increasing palm biodiesel ratio is conducted to evaluate engine performance test results. The qualifying of blended fuel properties was used to indicate the maximum blending ratio suitable for use in unmodified diesel engines according to the blended fuel standard ASTM D7467. The property test results revealed that blended fuel properties meet blended fuel standard requirements at up to 30% palm oil biodiesel. Furthermore, blending is efficient for reduction of the pour point from 14 °C for unblended biodiesel to less than 0 °C at a 30% biodiesel blending ratio. However, the energy content reduces by about 1.42% for each 10% increment of biodiesel. Engine test results demonstrated that there was no statistically significant difference for engine brake thermal efficiency among tested blended fuels compared to mineral diesel, and the lowest engine cyclic variation was achieved with blended fuel B30.     

Properties and use of jatropha curcas oil and diesel fuel blends in compression ignition engine

In the present investigation the high viscosity of the jatropha curcas oil which has been considered as a potential alternative fuel for the compression ignition (C.I.) engine was decreased by blending with diesel. The blends of varying proportions of jatropha curcas oil and diesel were prepared, analyzed and compared with diesel fuel. The effect of temperature on the viscosity of biodiesel and jatropha oil was also studied. The performance of the engine using blends and jatropha oil was evaluated in a single cylinder C.I. engine and compared with the performance obtained with diesel. Significant improvement in engine performance was observed compared to vegetable oil alone. The specific fuel consumption and the exhaust gas temperature were reduced due to decrease in viscosity of the vegetable oil. Acceptable thermal efficiencies of the engine were obtained with blends containing up to 50% volume of jatropha oil. From the properties and engine test results it has been established that 40–50% of jatropha oil can be substituted for diesel without any engine modification and preheating of the blends.     

Effect of an emission-reducing soluble hybrid nanocatalyst in diesel/biodiesel blends on exergetic performance of a DI diesel engine

The present study was set to explore the effect of a novel soluble hybrid nanocatalyst in diesel/biodiesel fuel blends on exergetic performance parameters of a DI diesel engine. Experiments were carried out using two types of diesel/biodiesel blends (i.e., B5 and B20) at four concentrations (0, 30, 60 and 90 ppm) of the hybrid nanocatalyst, i.e., cerium oxide immobilized on amide-functionalized multiwall carbon nanotubes (MWCNT). Furthermore, the exergy analysis was performed at five different loads and two engine speeds. The results obtained revealed that the exergetic parameters were profoundly influenced by engine speed and load. In general, increasing engine speed and load increased the magnitude of the destructed exergy. Moreover, the exergy efficiency increased by increasing engine load, while it decreased by elevating engine speed. However, the applied fuel blends had approximately similar exergetic efficiency and sustainability index. Interestingly, a remarkable reduction in emissions was obtained by incorporating the soluble catalyst nanoparticles to the diesel/biodiesel blends. Thus, it could be concluded that the diesel/biodiesel blends containing amide-functionalized MWCNTs-CeO₂ catalyst might substitute the use of pure diesel fuel without any unfavorable change in the exergetic performance parameters of the DI engines.     

Enhancing compression ignition engine performance using biodiesel/diesel blends and HHO gas

The proposed experimental study aims to investigate the effect of adding HHO gas with a constant flowrate (50% of the engine capacity) on the thermal efficiency for six different Biodiesel/diesel blends, which are 0B, 10B, 15%B, 20B, 25B and 30B. For all the studied fuelling scenarios, it was decided to mix HHO gas with the inlet air perpendicularly on the air streamline by a constant flowrate aiming to enhance the thermal efficiency of the engine. The study assumed maintain the rotational speed of the engine is constant (four different speeds) while varying the engine torque. The experimental results were recorded for four different rotational speeds of the engine, which are 1500, 1750, 2000 and 2250 RPM. Obtained results investigated that, increasing biodiesel content resulted in reducing the engine's brake thermal efficiency and increasing its brake specific fuel consumption due to the relatively lower heat content of the biodiesel comparing with conventional diesel. Adding HHO gas to the engine resulted in enhancing the thermal efficiency due to its high heat content and it was observed that; 20B with HHO gas supply provided the highest brake thermal efficiency of the engine as well as reducing its brake specific fuel consumption.     

The effects of turbocharger on the performance and exhaust emissions of a diesel engine fuelled with biodiesel

This paper investigates the effects of turbocharger on the performance of a diesel engine using diesel fuel and biodiesel in terms of brake power, torque, brake specific consumption and thermal efficiency, as well as CO and NO_x emissions. For this aim, a naturally aspirated four-stroke direct injection diesel engine was tested with diesel fuel and neat biodiesel, which is rapeseed oil methyl ester, at full load conditions at the speeds between 1200 and 2400 rpm with intervals of 200 rpm. Then, a turbocharger system was installed on the engine and the tests were repeated for both fuel cases. The evaluation of experimental data showed that the brake thermal efficiency of biodiesel was slightly higher than that of diesel fuel in both naturally aspirated and turbocharged conditions, while biodiesel yielded slightly lower brake power and torque along with higher fuel consumption values. It was also observed that emissions of CO in the operations with biodiesel were lower than those in the operations with diesel fuel, whereas NO_x emission in biodiesel operation was higher. This study reveals that the use of biodiesel improves the performance parameters and decreases CO emissions of the turbocharged engine compared to diesel fuel.     

The effects of blending diesel,ethanol, and biodiesel

This work investigated the feasibility of using a blend of standard Brazilian diesel (which contains 5% biodiesel) and up to 5% ethanol. The mixture was characterized as fuel and the performance of a diesel engine operating with a blend containing 3% anhydrous ethanol, the maximum percentage of ethanol that did not reduce the cetane number of the fuel below that specified in Brazilian legislation (ANP Resolution 42), was measured. The presence of anhydrous ethanol in the mixture did not cause a significant impact on engine performance as measured by brake power, brake torque, and brake specific fuel consumption tests. The thermal efficiency of the engine used in the tests was slightly higher with standard diesel than with the diesel-biodiesel-ethanol blend.     

An experimental investigation on the application potential of heterogeneous catalyzed Nahar biodiesel and its diesel blends as diesel engine fuels

From the inception of commercialization of biodiesel, feedstock scarcity is a major issue to be pondered upon in developing countries. In this study, an attempt has been made to use an abundantly available underutilized high oil content (67% of Nahar seed kernel) feedstock derived biodiesel in a compression ignition engine. The experimental investigation on diesel engine reveals slightly reduced brake thermal efficiency and excellent exhaust emissions up to 40% blending of Nahar biodiesel with conventional diesel fuel. At full load, compared to diesel fuel, the BTE dropped by 1.64% and 1.83%, whereas the BSFC increased by 5.07% and 6.76% for B30 and B40 blends, respectively. The tested emission parameters such as CO, HC, NOx, and smoke were decreased by 12.66%, 17.99%, 8.31%, and 10.61% for B30 and 4.87%, 12.76%, 7.98%, and 11.78% for B40, respectively, compared to diesel fuel.

Abbreviation: BD: Biodiesel; DF: Diesel fuel     

A renewable pathway towards increased utilization of hydrogen in diesel engines

In the present work, dual fuel operation of a diesel engine has been experimentally investigated using biodiesel and hydrogen as the test fuels. Jatropha Curcas biodiesel is used as the pilot fuel, which is directly injected in the combustion chamber using conventional diesel injector. The main fuel (hydrogen) is injected in the intake manifold using a hydrogen injector and electronic control unit. In dual fuel mode, engine operations are studied at varying engine loads at the maximum pilot fuel substitution conditions. The engine performance parameters such as maximum pilot fuel substitution, brake thermal efficiency and brake specific energy consumption are investigated. On emission side, oxides of nitrogen, hydrocarbon, carbon monoxide and smoke emissions are analysed. Based on the results, it is found that biodiesel-hydrogen dual fuel engine could utilize up to 80.7% and 24.5% hydrogen (by energy share) at low and high loads respectively along with improved brake thermal efficiency. Furthermore, hydrocarbon, carbon monoxide and smoke emissions are significantly reduced compared to single fuel diesel engine operation. Exhaust gas recirculation (EGR) has also been studied with biodiesel-hydrogen dual fuel engine operations. It is found that EGR could improve the utilization of hydrogen in dual fuel engine, especially at the high loads. The effect of EGR is also found to reduce high nitrogen oxide emissions from the dual fuel engine and brake thermal efficiency is not significantly affected.     

Effect of ethanol blending with biodiesel on engine performance and exhaust emissions in a CI engine

The use of biodiesel as an alternative diesel engine fuel is increasing rapidly. However, due to technical deficiencies, they are rarely used purely or with high percentages in unmodified diesel engines. Therefore, in this study, we used ethanol as an additive to research the possible use of higher percentages of biodiesel in an unmodified diesel engine. Commercial diesel fuel, 20% biodiesel and 80% diesel fuel, called here as B20, and 80% biodiesel and 20% ethanol, called here as BE20, were used in a single cylinder, four strokes direct injection diesel engine. The effect of test fuels on engine torque, power, brake specific fuel consumption, brake thermal efficiency, exhaust gas temperature, and CO, CO₂, NO_x and SO₂ emissions was investigated. The experimental results showed that the performance of CI engine was improved with the use of the BE20 especially in comparison to B20. Besides, the exhaust emissions for BE20 were fairly reduced.     

丙酮-丁醇-乙醇(ABE)/汽油混合燃料对高速发动机性能影响的试验研究

以发动机4000r/min、节气门开度35%为试验工况,对纯汽油及不同掺混体积分数丙酮-丁醇-乙醇(acetone-butanol-ethanol,ABE)与汽油混合物开展了不同点火提前角和喷油量的试验研究。分析了不同ABE混合比、点火提前角和过量空气系数对发动机性能的影响,并对每种燃料发动机最大功率工况的性能参数进行了比较。结果表明：点火提前角和过量空气系数相同时,混合燃料中ABE含量越高,燃油流量越大,发动机功率越大,有效热效率越高;燃油流量的总热量增大和热-功转换效率提高是促使发动机功率增大的主要原因;随ABE掺混比增加,NO比排放明显降低,CO比排放略有增加,碳氢化合物比排放先增后减。浓混合气工况增加ABE含量比在当量空燃比状态下增加ABE含量,发动机的有效热效率增大更明显,发动机的NO比排放降低更加明显。研究表明高速汽油机掺混ABE燃料具有较好的应用前景。